AV:RetroTINK-4K: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
RetroTINK-4K GUI Map: | ==RetroTINK-4K GUI Map:== | ||
Basic Setup: | ===Basic Setup:=== | ||
Input Selection | Input Selection | ||
Front: | Front: | ||
| Line 93: | Line 93: | ||
Firmware Update: | Firmware Update: | ||
Check SD Card | Check SD Card | ||
Advanced Setup: | ===Advanced Setup:=== | ||
RGB/Component ADC | RGB/Component ADC | ||
(RGB/Component ADC Setup) | (RGB/Component ADC Setup) | ||
| Line 149: | Line 149: | ||
Input Override: | Input Override: | ||
Input Swap: | Input Swap: | ||
Profiles: | ===Profiles:=== | ||
(Profiles) | (Profiles) | ||
Load Profile: | Load Profile: | ||
| Line 172: | Line 172: | ||
Button 12: | Button 12: | ||
Power Up: | Power Up: | ||
Device: | ===Device:=== | ||
Status | Status | ||
System Status Page 1: | System Status Page 1: | ||
Revision as of 07:58, 19 August 2023
RetroTINK-4K GUI Map:
Basic Setup:
Input Selection Front: Composite S-Video RCA: YPbPr RGsB CVBS on Green SCART: RGBS (75 ohm) RGsB YPbPr CVBS on Pin 20 CBVS on Green Y/C on Pin 20/Red HD-15: RGBHV RGBS RGsB YPbPr CBVS on Hsync CBVS on Green Y/C on Green/Red HDMI:
HDMI Output:
Scaling/Croppping Input Crop: Left Trim: Right Trim: Top Trim: Bottom Trim: Vert. Pre-Scale: Scaler: Aspect Correction: Scaling Mode: Vert. Factor: Hori. Factor: Interpolation: Vert. Kernel: Hori: Kernel: Buffer: Length: Image Processing Scanline: Function: Strength: Modulation: Red Bleed: Red Convergence: Blue Convergence: Mask: Enable: Strength: Load from File: Select a Mask File: RGB Masks: Mono Masks: Horizontal Blur: Function: Boost: Gamma/Linear Light/HDR: Input Factor: Output Factor: SMPTE 2048 PQ: Deinterlacer (Deinterlacer Setup) Mode: Algorithm: Field Inversion: Motion Adaptive Settings: Sensitivity: Interpolator: Detector: Bob Settings: Offset:
System: (System Setup) On Screen Display: Position: Auto-Off: Load Banner: Enable Debug OSD: Blanking Color: Red: Green: Blue: Firmware Update: Check SD Card
Advanced Setup:
RGB/Component ADC (RGB/Component ADC Setup) Sampling Rate: Decimation Factor: Decimation Phase: Sub-Phase: Anti-Alias: Sync: SoG Threshold: Pre-coast: Post-coast: Gain: Pre-ADC: Red: Green: Blue: Auto Calibrate: Phase: Gain: HDMI Receiver Reciever Decimation Factor: Decimation Phase: Color Space: 4:2:2 Upsampler: CSC Mode: Input RGB Range:
SDP Decoder (SDP Decoder Setup) Gain/Balance Brightness: Contrast: Chroma: Phase: Blue Only: Setup:
Processing: Y/C Filter: Comb Bandwidth: Chroma Bandwidth: Sharpness: CTIE: Sync: H-Lock Speed: Standard: Audio Input (Audio Setup) Sampling Sampling Rate: Pre-amp Gain: Source Input Override: Input Swap:
Profiles:
(Profiles) Load Profile: Load Default Load From File (opens file selector window titled "Select Profile") Save Profile: Save Current Save As New Assign Profile: Button 1: Button 2: Button 3: Button 4: Button 5: Button 6: Button 7: Button 8: Button 9: Button 10: Button 11: Button 12: Power Up:
Device:
Status System Status Page 1: Video Source: CP Proc. (I assume CP Proc will change based on selection) Input Timing: Pixel Clock: Freq: Detected Mode: Audio Input: I2S (I assume will change based on audio input) Measured Freq: HDMI SR: HDMI N / CTS: FPGA Core Scaler Clock: PLL VCO: Pipeline: SDRAM Clock: SDRAM Load: HDMI Transmitter Output Timing: Active Size: Pixel Clock: HDMI Standard: PIC32MX MCU System Clock: Uptime: Loop Time: Last IR Code: SD Card Free: System Status Page 2: System Status Page 3: Diagnostic Console About Device: FW Version Device ID: