AV:RetroTINK-4K: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
Line 94: Line 94:
Check SD Card
Check SD Card
===Advanced Setup:===
===Advanced Setup:===
====RGB/Component ADC====
====RGB/Component ADC====
(RGB/Component ADC Setup)
(RGB/Component ADC Setup)
Sampling Rate:
Sampling Rate:
Line 113: Line 113:
Phase:
Phase:
Gain:
Gain:
====HDMI Receiver====
====HDMI Receiver====
Reciever
Reciever
Decimation Factor:
Decimation Factor:
Line 122: Line 122:
Input RGB Range:
Input RGB Range:


====SDP Decoder====
====SDP Decoder====
(SDP Decoder Setup)
(SDP Decoder Setup)
Gain/Balance
Gain/Balance
Line 141: Line 141:
H-Lock Speed:
H-Lock Speed:
Standard:
Standard:
====Audio Input====
====Audio Input====
(Audio Setup)
(Audio Setup)
Sampling
Sampling
Line 149: Line 149:
Input Override:
Input Override:
Input Swap:
Input Swap:
===Profiles:===
===Profiles:===
(Profiles)
(Profiles)

Revision as of 08:04, 19 August 2023

RetroTINK-4K GUI Map

Basic Setup

Input Selection

Front: Composite S-Video RCA: YPbPr RGsB CVBS on Green SCART: RGBS (75 ohm) RGsB YPbPr CVBS on Pin 20 CBVS on Green Y/C on Pin 20/Red HD-15: RGBHV RGBS RGsB YPbPr CBVS on Hsync CBVS on Green Y/C on Green/Red HDMI:

HDMI Output:

Scaling/Croppping

Input Crop: Left Trim: Right Trim: Top Trim: Bottom Trim: Vert. Pre-Scale: Scaler: Aspect Correction: Scaling Mode: Vert. Factor: Hori. Factor: Interpolation: Vert. Kernel: Hori: Kernel: Buffer: Length:

Image Processing

Scanline: Function: Strength: Modulation: Red Bleed: Red Convergence: Blue Convergence: Mask: Enable: Strength: Load from File: Select a Mask File: RGB Masks: Mono Masks: Horizontal Blur: Function: Boost: Gamma/Linear Light/HDR: Input Factor: Output Factor: SMPTE 2048 PQ: ====Deinterlacer==== (Deinterlacer Setup) Mode: Algorithm: Field Inversion: Motion Adaptive Settings: Sensitivity: Interpolator: Detector: Bob Settings: Offset:

====System:==== (System Setup) On Screen Display: Position: Auto-Off: Load Banner: Enable Debug OSD: Blanking Color: Red: Green: Blue: Firmware Update: Check SD Card

Advanced Setup:

RGB/Component ADC

(RGB/Component ADC Setup) Sampling Rate: Decimation Factor: Decimation Phase: Sub-Phase: Anti-Alias: Sync: SoG Threshold: Pre-coast: Post-coast: Gain: Pre-ADC: Red: Green: Blue: Auto Calibrate: Phase: Gain:

HDMI Receiver

Reciever Decimation Factor: Decimation Phase: Color Space: 4:2:2 Upsampler: CSC Mode: Input RGB Range:

SDP Decoder

(SDP Decoder Setup) Gain/Balance Brightness: Contrast: Chroma: Phase: Blue Only: Setup:

Processing: Y/C Filter: Comb Bandwidth: Chroma Bandwidth: Sharpness: CTIE: Sync: H-Lock Speed: Standard:

Audio Input

(Audio Setup) Sampling Sampling Rate: Pre-amp Gain: Source Input Override: Input Swap:

Profiles:

(Profiles) ====Load Profile:==== Load Default Load From File (opens file selector window titled "Select Profile") Save Profile: Save Current Save As New ====Assign Profile:==== Button 1: Button 2: Button 3: Button 4: Button 5: Button 6: Button 7: Button 8: Button 9: Button 10: Button 11: Button 12: Power Up:

Device:

====Status==== System Status Page 1: Video Source: CP Proc. (I assume CP Proc will change based on selection) Input Timing: Pixel Clock: Freq: Detected Mode: Audio Input: I2S (I assume will change based on audio input) Measured Freq: HDMI SR: HDMI N / CTS: FPGA Core Scaler Clock: PLL VCO: Pipeline: SDRAM Clock: SDRAM Load: HDMI Transmitter Output Timing: Active Size: Pixel Clock: HDMI Standard: PIC32MX MCU System Clock: Uptime: Loop Time: Last IR Code: SD Card Free: System Status Page 2: System Status Page 3: ====Diagnostic Console==== ====About==== Device: FW Version Device ID: