AV:RetroTINK-4K: Difference between revisions
Line 3: | Line 3: | ||
===Basic Setup=== | ===Basic Setup=== | ||
====Input Selection==== | ====Input Selection==== | ||
{| class=" | {| class="comparisontable" | ||
|- | |- | ||
! colspan="2" style="text-align:left;"| Front | ! colspan="2" style="text-align:left;"| Front |
Revision as of 08:29, 19 August 2023
RetroTINK-4K GUI Map
Basic Setup
Input Selection
Front | |
---|---|
Composite | information |
S-Video | information |
RCA | |
YPbPr | information |
RGsB | information |
CVBS on Green | information |
SCART | |
RGBS (75 ohm) | information |
RGsB | information |
YPbPr | information |
CVBS on Pin 20 | information |
CBVS on Green | information |
Y/C on Pin 20/Red | information |
HD-15 | |
RGBHV | information |
RGBS | information |
RGsB | information |
YPbPr | information |
CBVS on Hsync | information |
CBVS on Green | information |
Y/C on Green/Red | information |
HDMI | |
thing a | information |
thing b | information |
HDMI Output:
Scaling/Croppping
Input Crop: Left Trim: Right Trim: Top Trim: Bottom Trim: Vert. Pre-Scale: Scaler: Aspect Correction: Scaling Mode: Vert. Factor: Hori. Factor: Interpolation: Vert. Kernel: Hori: Kernel: Buffer: Length:
Image Processing
Scanline: Function: Strength: Modulation: Red Bleed: Red Convergence: Blue Convergence: Mask: Enable: Strength: Load from File: Select a Mask File: RGB Masks: Mono Masks: Horizontal Blur: Function: Boost: Gamma/Linear Light/HDR: Input Factor: Output Factor: SMPTE 2048 PQ:
Deinterlacer
(Deinterlacer Setup) Mode: Algorithm: Field Inversion: Motion Adaptive Settings: Sensitivity: Interpolator: Detector: Bob Settings: Offset:
System:
(System Setup) On Screen Display: Position: Auto-Off: Load Banner: Enable Debug OSD: Blanking Color: Red: Green: Blue: Firmware Update: Check SD Card
Advanced Setup:
RGB/Component ADC
(RGB/Component ADC Setup) Sampling Rate: Decimation Factor: Decimation Phase: Sub-Phase: Anti-Alias: Sync: SoG Threshold: Pre-coast: Post-coast: Gain: Pre-ADC: Red: Green: Blue: Auto Calibrate: Phase: Gain:
HDMI Receiver
Reciever Decimation Factor: Decimation Phase: Color Space: 4:2:2 Upsampler: CSC Mode: Input RGB Range:
SDP Decoder
(SDP Decoder Setup) Gain/Balance Brightness: Contrast: Chroma: Phase: Blue Only: Setup:
Processing: Y/C Filter: Comb Bandwidth: Chroma Bandwidth: Sharpness: CTIE: Sync: H-Lock Speed: Standard:
Audio Input
(Audio Setup) Sampling Sampling Rate: Pre-amp Gain: Source Input Override: Input Swap:
Profiles:
(Profiles)
Load Profile:
Load Default Load From File (opens file selector window titled "Select Profile") Save Profile: Save Current Save As New
Assign Profile:
Button 1: Button 2: Button 3: Button 4: Button 5: Button 6: Button 7: Button 8: Button 9: Button 10: Button 11: Button 12: Power Up:
Device:
Status
System Status Page 1: Video Source: CP Proc. (I assume CP Proc will change based on selection) Input Timing: Pixel Clock: Freq: Detected Mode: Audio Input: I2S (I assume will change based on audio input) Measured Freq: HDMI SR: HDMI N / CTS: FPGA Core Scaler Clock: PLL VCO: Pipeline: SDRAM Clock: SDRAM Load: HDMI Transmitter Output Timing: Active Size: Pixel Clock: HDMI Standard: PIC32MX MCU System Clock: Uptime: Loop Time: Last IR Code: SD Card Free: System Status Page 2: System Status Page 3:
Diagnostic Console
About
Device: FW Version Device ID: