AV:RetroTINK-4K: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
Line 89: Line 89:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Input Crop
! colspan="2" style="text-align:left;"| Input Crop
|-
|-
| Left Trim
| Left Trim
Line 108: Line 108:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Scaler
! colspan="2" style="text-align:left;"| Scaler
|-
|-
| Aspect Correction
| Aspect Correction
Line 124: Line 124:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Interpolation
! colspan="2" style="text-align:left;"| Interpolation
|-
|-
| Vert. Kernel
| Vert. Kernel
Line 134: Line 134:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Buffer
! colspan="2" style="text-align:left;"| Buffer
|-
|-
| Length
| Length

Revision as of 08:48, 19 August 2023

RetroTINK-4K GUI Map

Basic Setup

Input Selection

Front
Composite information
S-Video information
RCA
YPbPr information
RGsB information
CVBS on Green information
SCART
RGBS (75 ohm) information
RGsB information
YPbPr information
CVBS on Pin 20 information
CBVS on Green information
Y/C on Pin 20/Red information
HD-15
RGBHV information
RGBS information
RGsB information
YPbPr information
CBVS on Hsync information
CBVS on Green information
Y/C on Green/Red information
HDMI
thing a information
thing b information

HDMI Output:

Scaling/Cropping

Input Crop
Left Trim information
Right Trim information
Top Trim information
Bottom Trim information
Vert. Pre-Scale information
Scaler
Aspect Correction information
Scaling Mode information
Vert. Factor information
Hori. Factor information
Interpolation
Vert. Kernel information
Hori: Kernel information
Buffer
Length information

Image Processing

Scanline: Function: Strength: Modulation: Red Bleed: Red Convergence: Blue Convergence: Mask: Enable: Strength: Load from File: Select a Mask File: RGB Masks: Mono Masks: Horizontal Blur: Function: Boost: Gamma/Linear Light/HDR: Input Factor: Output Factor: SMPTE 2048 PQ:

Deinterlacer

(Deinterlacer Setup) Mode: Algorithm: Field Inversion: Motion Adaptive Settings: Sensitivity: Interpolator: Detector: Bob Settings: Offset:

System:

(System Setup) On Screen Display: Position: Auto-Off: Load Banner: Enable Debug OSD: Blanking Color: Red: Green: Blue: Firmware Update: Check SD Card

Advanced Setup:

RGB/Component ADC

(RGB/Component ADC Setup) Sampling Rate: Decimation Factor: Decimation Phase: Sub-Phase: Anti-Alias: Sync: SoG Threshold: Pre-coast: Post-coast: Gain: Pre-ADC: Red: Green: Blue: Auto Calibrate: Phase: Gain:

HDMI Receiver

Reciever Decimation Factor: Decimation Phase: Color Space: 4:2:2 Upsampler: CSC Mode: Input RGB Range:

SDP Decoder

(SDP Decoder Setup) Gain/Balance Brightness: Contrast: Chroma: Phase: Blue Only: Setup:

Processing: Y/C Filter: Comb Bandwidth: Chroma Bandwidth: Sharpness: CTIE: Sync: H-Lock Speed: Standard:

Audio Input

(Audio Setup) Sampling Sampling Rate: Pre-amp Gain: Source Input Override: Input Swap:

Profiles:

(Profiles)

Load Profile:

Load Default Load From File (opens file selector window titled "Select Profile") Save Profile: Save Current Save As New

Assign Profile:

Button 1: Button 2: Button 3: Button 4: Button 5: Button 6: Button 7: Button 8: Button 9: Button 10: Button 11: Button 12: Power Up:

Device:

Status

System Status Page 1: Video Source: CP Proc. (I assume CP Proc will change based on selection) Input Timing: Pixel Clock: Freq: Detected Mode: Audio Input: I2S (I assume will change based on audio input) Measured Freq: HDMI SR: HDMI N / CTS: FPGA Core Scaler Clock: PLL VCO: Pipeline: SDRAM Clock: SDRAM Load: HDMI Transmitter Output Timing: Active Size: Pixel Clock: HDMI Standard: PIC32MX MCU System Clock: Uptime: Loop Time: Last IR Code: SD Card Free: System Status Page 2: System Status Page 3:

Diagnostic Console

About

Device: FW Version Device ID: