AV:RetroTINK-4K

Notes

Deinterlacer -> -> Motion Adaptive Settings -> Sensitivity

---

(medium and high options might be might be reversed) Controls combing effect at costs of sharpness. Low = less combing.

Deinterlacer -> -> Motion Adaptive Settings -> Interpolator:

---

Basically controls how the "bob" portion of the MA is calculated. The bob is either taken from the line above, line below or the average of the upper and lower lines BFI. It's a matter of preference. I think either Top or Bottom interpolator looks a little sharper. Average is softer In the end it doesn't matter too much because Bob is only used during motion when it is hard to see detail anwyays

Deinterlacer -> Motion Adaptive Settings -> Detector:

---

This is a little complicated to explain... but let me try basically symmetric adds one frame of lag but the motion detection may be better. Because it is looking "one field into the future" idk if its really better tho in real life

HDMI -> BFI Control

---

-Strobe: How much the frame is divided down (i.e. 1 = divide by 2, 2 = divide by 3, 3 = divide by 4) from input to output -Blur: How many frames are ON vs OFF. So let's say we are converting 60 Hz -> 240 Hz. Blur = 1, ON, OFF, OFF, OFF. Blur = 2 is ON, ON, OFF, OFF -LCD Saver - inverts the pattern of the BFI to avoid renetion. But every few minutes u will see a flicker

RetroTINK-4K GUI Map

Basic Setup

Input Selection

Front
Composite	information
S-Video	information

RCA
YPbPr	information
RGsB	information
CVBS on Green	information

SCART
RGBS (75 ohm)	information
RGsB	information
YPbPr	information
CVBS on Pin 20	information
CBVS on Green	information
Y/C on Pin 20/Red	information

HD-15
RGBHV	information
RGBS	information
RGsB	information
YPbPr	information
CBVS on Hsync	information
CBVS on Green	information
Y/C on Green/Red	information

HDMI
thing a	information
thing b	information

HDMI Output

Transmitter

Deep Color
HDR
Sync Lock
Vrr

BFI Control

Strobe
Blur
LCD Saver

Output Resolution

4K60

4K50 1080p60 1080p50 1080p100 1440p100 1080p120 1440p120 480p60 2880x2160p70.00 1920x2160p60.00 800x600p60.00 1920x1200p60.00

Scaling/Cropping

Input Crop
Left Trim	information
Right Trim	information
Top Trim	information
Bottom Trim	information
Vert. Pre-Scale	information

Scaler
Aspect Correction	information
Scaling Mode	information
Vert. Factor	information
Hori. Factor	information

Interpolation
Vert. Kernel	information
Hori. Kernel	information

Buffer
Length	information

Image Processing

Scanline
Function	information
Strength	information
Modulation	information
Red Bleed	information
Red Convergence	information
Blue Convergence	information

Mask
Enable	information
Strength	information
Load from File	Select a Mask File, RGB Masks:, Mono Masks:

Horizontal Blur
Function	information
Boost	information

Gamma/Linear Light/HDR
Input Factor	information
Output Factor	information
SMPTE 2048 PQ	information

Deinterlacer

Mode
Algorithm:	information
Field Inversion:	information

Motion Adaptive Settings
Sensitivity	information
Interpolator	information
Detector	information

Bob Settings
Offset	information

System

On Screen Display
Position	information
Auto-Off	information
Load Banner	information
Enable Debug OSD	information

Blanking Color:
Red	information
Green	information
Blue	information

Firmware Update
Check SD Card	information

Advanced Setup:

RGB/Component ADC

Sampling
Sampling Rate	information
Decimation Factor	information
Decimation Phase	information
Sub-Phase	information
Anti-Alias	information

Sync
SoG Threshold	information
Pre-coast	information
Post-coast	information

Gain
Pre-ADC	information
Red	information
Green	information
Blue	information

Auto Calibrate
Phase	information
Gain	information

HDMI Receiver

Receiver
Decimation Factor	information
Decimation Phase	information

Color Space
4:2:2 Upsampler	information
CSC Mode:	information
Input RGB Range	information

SDP Decoder

Gain/Balance
Brightness	information
Contrast	information
Chroma	information
Phase	information
Blue Only	information
Setup	information

Processing
Y/C Filter	information
Comb Bandwidth	information
Chroma Bandwidth	information
Sharpness	information
CTIE	information

Sync
H-Lock Speed	information
Standard	information

Audio Input

Sampling
Sampling Rate	information
Pre-amp Gain	information

Source
Input Override	information
Input Swap	information

Profiles

Load Profile
Load Default	information
Load From File	(opens file selector window titled "Select Profile")

Save Profile
Save Current	information
Save As New	information

Assign Profile
Button 1	information
Button 2	information
Button 3	information
Button 4	information
Button 5	information
Button 6	information
Button 7	information
Button 8	information
Button 9	information
Button 10	information
Button 11	information
Button 12	information
Power Up	information

Device

Status

System Status Page 1:

Video Source
Video Source	CP Proc. (I assume CP Proc will change based on selection)
Input Timing	information
Pixel Clock	information
Freq	information
Detected Mode	information

Audio Input
Audio Input	I2S (I assume will change based on audio input)
Measured Freq	information
Measured Freq	information
HDMI N / CTS	information

FPGA Core
Scaler Clock	information
PLL VCO	information
Pipeline	information
SDRAM Clock	information
SDRAM Load	information

HDMI Transmitter
Output Timing	information
Active Size	information
Pixel Clock	information
HDMI Standard	information

PIC32MX MCU
System Clock	information
Uptime	information
Loop Time	information
Last IR Code	information
SD Card Free	information

System Status Page 2:

to do

System Status Page 3:

to do

Diagnostic Console

to do

About

About
Device:	information
FW Version	information
Device ID:	information