SNES:Buying Guide

There are two major variants of the SNES and Super Famicom, with the original model having a number of different revisions. This buying guide serves to delineate the differences between these revisions and briefly explain what to look for when adding an SNES or Super Famicom to your setup.

Original Model (SNS-001/SNSP-001/SHVC-001)

• Released in the following regions:
  • Japan: November 1990
  • North America: August 1991
  • PAL regions: 1992
  • South Korea: 1992
  • Brazil: August 1993
• Has two major cosmetic designs, a rounded one which was used in Japan, Korea and PAL territories, and a more rectangular design used in North America and Brazil
• Outputs composite video, S-video, RGB and stereo audio from a custom multiout connector
  • All except French models also have RF output
• The power input jack differs between regions:
  • Super Famicom consoles take a 5.5 x 2.1 mm barrel jack with tip negative polarity, power supply specifications are the same as the original Famicom
  • US SNES consoles take a 6.9 x 4.1 mm barrel jack with a center pin and tip negative polarity
  • PAL SNES consoles take a 5.5 x 2.5 mm barrel jack with AC voltage, power supply specifications are the same as the PAL NES
• Earlier US SNES consoles and all PAL and JP consoles have a cartridge lock mechanism designed to prevent cartridges being removed while the console is powered on
• Consoles with an SHVC-CPU-01 board revision have serious longevity concerns, as an increasing number of these consoles are experiencing chip failures. These failures usually afflict the CPU and/or both PPUs, and manifest as issues such as corrupted graphics, booting only certain games, or controllers not working. In addition, these consoles are also beginning to suffer from leaky capacitors, which can cause various problems and can damage the board if not rectified in time. Because of these growing problems, consoles with an SHVC-CPU-01 board are not recommended, especially if they are being sold as "untested". Thankfully, these revisions are easily discerned by looking at the bottom of the console. If it has four rubber feet on the bottom, it will have an SHVC-CPU-01 board. All later board revisions only have two rubber feet at the front.
  • If you do decide to purchase an SHVC-CPU-01 console, make absolutely sure it is fully tested and if possible, run the SNES Burn-In Test to ensure the console is actually functioning properly.

Board Revisions

Nintendo produced many revisions of the model 1, with each revision consolidating chips and/or circuitry to reduce production costs.

Photo	Revision Name	Date Range	Regions	Notes
(image needed)	SHVC-CPU-01	1990-1992	NTSC	Has a removable cartridge port and a separate module which contains the sound hardware. Highly susceptible to chip failure and leaky capacitors.
(image needed)	SNS-CPU-GPM-01/02	1992-1994	NTSC	Incorporates the sound hardware onto the motherboard. Video quality is slightly worse than the SHVC-CPU-01. Cartridge port is still removable.
(image needed)	SNSP-CPU-01/02	1992-1995	PAL	Similar to the GPM-01/02, but adds a circuit which generates 12V DC for SCART autoswitching
(image needed)	SNS-CPU-RGB-01/02	1994-1995	NTSC	Has simplified video circuitry.
(image needed)	SNS-CPU-APU-01	1995	NTSC	Consolidates most of the sound hardware into a single chip, the S-APU. Has video quality issues through RGB due to a poorly routed color subcarrier trace. Last of the 2-chip/3-chip boards.
(image needed)	SNS-CPU-1CHIP-01/02/03	1995-1996	NTSC	Consolidates the CPU, PPU1 and PPU2 into a single ASIC. Video quality is considerably sharper but is also overly bright and has some slight ghosting. Also has compatibility issues with several games. The -03 revision does not have the circuitry for composite sync populated.
(image needed)	SNSP-CPU-1CHIP-01/02	1995-1996	PAL	PAL version of the 1CHIP.

New-Style SNES/Super Famicom Jr.

• Only released in North America (October 1997) and Japan (January 1998)