Xbox 360:RGH/Solder Points: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
(Made a new page with pictures for RGH solder points)
 
 
(21 intermediate revisions by the same user not shown)
Line 1: Line 1:
== Phat ==
== Phat ==


=== 3.3v  [[File:Y5p0dxP.jpg|331x331px]] ===
=== 3.3v, 5v, GND, and RGH 2 i2C ===


=== 1.8V '''(Only if using an X360 ACE)''' ===
* J2B1
** [[File:J2B1.png|482x482px]]


==== Non-Xenon [[File:1v8-HDMI.png|frameless]] ====
=== 1.8V '''(Only if using an X360 ACE V1/V2/V3)''' ===


==== Xenon ====
* '''Non-Xenon'''
[[File:1v8-Xenon.png|frameless]]
** [[File:1v8-HDMI.png|frameless]]
* '''Xenon'''
** [[File:1v8-Xenon.png|frameless]]
[[File:Phat360PLLFix.jpg|thumb|400x400px|PLL Repair on a Phat motherboard (required if bottom pad is damaged). Image credit to TheLazyITGuy.]]


=== PLL ===
=== CPU_RST ===
* C7R112
** [[File:RST.png|frameless]]
* R8C2
** [[File:VXi9LgC.jpg|frameless|311x311px]]


==== Bottom  [[File:Fat360PLL.jpg|frameless|290x290px]] ====
* J8C1
** '''Will not work with EXT_CLK.'''
** [[File:Cp2OBF3.jpeg|frameless|338x338px]]


==== Top (under CPU heatsink; requires scraping) [[File:Fat360topPLL.jpg|frameless|288x288px]] ====
=== EXT_CLK ===
* Bottom (Under CPU)
** [[File:EXT_CLK.png]]


=== STBY_CLK ===
=== FT6U1 POST (RGH 1.2 or EXT_CLK) ===
* Bottom
** [[File:Post.png|frameless|287x287px]]
* Top (requires scraping)
** [[File:FT6U1 topside.png|frameless|285x285px]]


==== Top (Non-Xenon) [[File:Fat360STBY CLK.jpg|frameless|286x286px]] ====
=== FT6U7 POST (RGH 1, 2, or 3) ===


* There are 2 points boxed; either can be used.
*Bottom
**[[File:WEFEjMr.jpg|300x300px]]
*Top (requires scraping)
**[[File:POST_OUT1_Top.jpg|300x300px|(requires scraping)]]


==== Top (Xenon) ====
=== GND ===
* [[Xbox 360:RGH/Solder Points#3.3v, GND, and RGH 2 i2C|J2B1 Header]]
*AV Port
*'''Any other ground point'''
=== PLL ===


==== Bottom [[File:CLK.png|frameless|287x287px]] ====
* Bottom
** [[File:Fat360PLL.jpg|frameless|290x290px]]
* Top (under CPU heatsink; requires scraping)
** [[File:Fat360topPLL.jpg|frameless|288x288px]]


=== POST ===
=== STBY_CLK ===


==== Bottom  [[File:Post.png|frameless|287x287px]] ====
* Top '''(Xenon)'''
** [[File:STBY_CLK-Xenon.png]]
* Top '''(Non-Xenon)'''
** [[File:Fat360STBY CLK.jpg|frameless|286x286px]]
** There are 2 points boxed; either can be used.


==== Top (requires scraping) [[File:FT6U1 topside.png|frameless|285x285px]] ====
* Bottom '''(Non-Xenon)'''
** [[File:CLK.png|frameless|287x287px]]


=== CPU_RST ===
=== SMC ===


==== R8C2  [[File:VXi9LgC.jpg|frameless|311x311px]] ====
*POST and PLL (Bottom)
**[[File:PhatRGH3SMC.png|frameless|300x300px]]
**Alternative SMC_PLL (Top)
***[[File:Topsidepoint.png|frameless|300x300px]]


==== C7R112  [[File:RST.png|frameless]] ====
==Trinity==


==== J8C1:  [[File:Cp2OBF3.jpeg|frameless|338x338px]] ====
=== 3.3v, 5v, GND, and RGH 2 i2C ===
* J2C3
** [[File:J2C3Trinity.png|frameless|391x391px]]


=== GND ===
=== CPU_CLK '''(Only if using an X360 ACE V4/V5)''' ===
*Top (HANA)
**[[File:TrinityC1C2.png|frameless|431x431px]]
** There are two points circled for C1 and C2 respectively; either can be used or bridged.


==== Near 3.3v  [[File:J2b1gnd.png|frameless|282x282px]] ====
*Bottom
**[[File:TrinityBottomC1C2.png|frameless|576x576px]]


==== AV Port ====
===PLL===


==== '''Any other ground point''' ====
*Bottom
**[[File:RGH1.2 Slim PLL.jpg|frameless|497x497px]]
**'''No alternative point!'''


== Slim (Trinity) ==
===POST & RST===


=== PLL  [[File:RGH1.2 Slim PLL.jpg|frameless|330x330px]] ===
* Bottom
** [[File:TrinityPOSTandRST.png|frameless|700x700px]]
** There are two RST points, either can be used.


==== No alternative point! ====
*Top (without postfix adapter)
**[[File:CoronaTrinityPOST.png|700x700px]]
*Top (with postfix Adapter)
**[[File:PostfixadapterV1 example.gif|frameless|700x700px]]
** A Postfix adapter can be used on Trinity in case the POST point is damaged.


=== CPU_CLK '''(Only if using an X360 ACE V4/V5)''' ===
===STBY_CLK===
*C3B10 (Top)
**[[File:TrinityHanaCLK.jpg|frameless|700x700px]]


==== Top  [[File:TrinityC1C2.png|frameless]] ====
*FT3N2 (Bottom)
**[[File:Ft3n2.jpg|frameless|700x700px]]


* There are two points circled for C1 and C2 respectively; either can be used or bridged.
=== SMC ===
*SMC_PLL is also used for Muffin/Mufas
*SMC_PLL
**Bottom
***[[File:FT2V1.png|FT2V1|615x615px]]
**Top
***[[File:Trinity smcpll.jpg|frameless|613x613px]]
*SMC_POST
**Bottom
***[[File:TrinitySMC_POST.png|R3R22]]
==Corona/Waitsburg/Stingray==


==== Bottom  [[File:TrinityBottomC1C2.png|frameless]] ====
=== 3.3v, 5v, GND, and RGH 2 i2C ===


==== POST & RST  [[File:TrinityPOSTandRST.png|frameless|328x328px]] ====
* J2C3
 
** [[File:J2C3Corona.png|frameless|418x418px]]
* There are two RST points, either can be used.
'''CPU_CLK (Only if using an X360 ACE V4/V5)'''
* A Postfix adapter can be used on Trinity in case it's damaged.
*Top
 
**[[File:CoronaCPUCLK.png|frameless|417x417px]]
==== STBY_CLK ====
*There are two points circled for C1 and C2 respectively, either can be used or bridged.
 
===== C3B10 (Top) [[File:TrinityHanaCLK.jpg|frameless]] =====
 
===== FT3N2 (Bottom)  [[File:Ft3n2.jpg|frameless|301x301px]] =====
 
==== GND & 3.3V  [[File:Trinity 3v3GND.png|frameless|350x350px]] ====


==Slim or E (Corona/Waitsburg/Stingray)==
===PLL===
[[File:5lY3TID.png|thumb|Postfix adapter installation guide]]
*Bottom
**[[File:RGH1.2 Slim PLL.jpg|frameless|391x391px]]
**No alternative point!


=== PLL [[File:RGH1.2 Slim PLL.jpg|frameless|329x329px]] ===
===POST & RST===


* No alternative point!
*Bottom
**[[File:Corona POSTandRST.png|frameless|392x392px]]
**There are two RST points; either can be used.
*Top (without postfix adapter)
**[[File:CoronaTrinityPOST.png|500x500px]]
*Top (Postfix Adapter)
**[[File:PostfixadapterV1 example.gif|frameless|391x391px]]
**If POST on the bottom is disabled (like in Waitsburg & Stingray boards) or damaged, a postfix adapter is required.


=== CPU_CLK '''(Only if using an X360 ACE V4/V5)''' [[File:CoronaCPUCLK.png|frameless|328x328px]] ===
=== SMC ===
*There are two points circled for C1 and C2 respectively, either can be used or bridged.
*The GPIO used for SMC_PLL is also used for Muffin/Mufas
*POST and PLL (Bottom)
**[[File:CoronaSMC.png|SMC_POST and SMC_PLL|533x533px]]
*Alternate SMC_PLL (Top, Southbridge)
**[[File:Coronasmcpost.jpg|frameless|488x488px]]
*Alternate SMC_PLL (Top, DB2G3)
**[[File:CoronaDB2G3.png|frameless|366x366px]]


=== POST & RST [[File:Corona POSTandRST.png|frameless|327x327px]] ===
===Postfix Adapter Installation & Identification Guide===
*There are two RST points, either can be used.
*If POST on the bottom is disabled (like in Waitsburg & Stingray boards) or damaged, a postfix adapter is required.


=== GND & 3.3V  [[File:Corona 3v3GND.png|frameless|325x325px]] ===
* [[File:Full Postfix Guide.png|frameless|2355x2355px]]

Latest revision as of 06:27, 27 June 2024

Phat

3.3v, 5v, GND, and RGH 2 i2C

  • J2B1
    • J2B1.png

1.8V (Only if using an X360 ACE V1/V2/V3)

  • Non-Xenon
    • 1v8-HDMI.png
  • Xenon
    • 1v8-Xenon.png
PLL Repair on a Phat motherboard (required if bottom pad is damaged). Image credit to TheLazyITGuy.

CPU_RST

  • C7R112
    • RST.png
  • R8C2
    • VXi9LgC.jpg
  • J8C1
    • Will not work with EXT_CLK.
    • Cp2OBF3.jpeg

EXT_CLK

  • Bottom (Under CPU)
    • EXT CLK.png

FT6U1 POST (RGH 1.2 or EXT_CLK)

  • Bottom
    • Post.png
  • Top (requires scraping)
    • FT6U1 topside.png

FT6U7 POST (RGH 1, 2, or 3)

  • Bottom
    • WEFEjMr.jpg
  • Top (requires scraping)
    • (requires scraping)

GND

PLL

  • Bottom
    • Fat360PLL.jpg
  • Top (under CPU heatsink; requires scraping)
    • Fat360topPLL.jpg

STBY_CLK

  • Top (Xenon)
    • STBY CLK-Xenon.png
  • Top (Non-Xenon)
    • Fat360STBY CLK.jpg
    • There are 2 points boxed; either can be used.
  • Bottom (Non-Xenon)
    • CLK.png

SMC

  • POST and PLL (Bottom)
    • PhatRGH3SMC.png
    • Alternative SMC_PLL (Top)
      • Topsidepoint.png

Trinity

3.3v, 5v, GND, and RGH 2 i2C

  • J2C3
    • J2C3Trinity.png

CPU_CLK (Only if using an X360 ACE V4/V5)

  • Top (HANA)
    • TrinityC1C2.png
    • There are two points circled for C1 and C2 respectively; either can be used or bridged.
  • Bottom
    • TrinityBottomC1C2.png

PLL

  • Bottom
    • RGH1.2 Slim PLL.jpg
    • No alternative point!

POST & RST

  • Bottom
    • TrinityPOSTandRST.png
    • There are two RST points, either can be used.
  • Top (without postfix adapter)
    • CoronaTrinityPOST.png
  • Top (with postfix Adapter)
    • PostfixadapterV1 example.gif
    • A Postfix adapter can be used on Trinity in case the POST point is damaged.

STBY_CLK

  • C3B10 (Top)
    • TrinityHanaCLK.jpg
  • FT3N2 (Bottom)
    • Ft3n2.jpg

SMC

  • SMC_PLL is also used for Muffin/Mufas
  • SMC_PLL
    • Bottom
      • FT2V1
    • Top
      • Trinity smcpll.jpg
  • SMC_POST
    • Bottom
      • R3R22

Corona/Waitsburg/Stingray

3.3v, 5v, GND, and RGH 2 i2C

  • J2C3
    • J2C3Corona.png

CPU_CLK (Only if using an X360 ACE V4/V5)

  • Top
    • CoronaCPUCLK.png
  • There are two points circled for C1 and C2 respectively, either can be used or bridged.

PLL

  • Bottom
    • RGH1.2 Slim PLL.jpg
    • No alternative point!

POST & RST

  • Bottom
    • Corona POSTandRST.png
    • There are two RST points; either can be used.
  • Top (without postfix adapter)
    • CoronaTrinityPOST.png
  • Top (Postfix Adapter)
    • PostfixadapterV1 example.gif
    • If POST on the bottom is disabled (like in Waitsburg & Stingray boards) or damaged, a postfix adapter is required.

SMC

  • The GPIO used for SMC_PLL is also used for Muffin/Mufas
  • POST and PLL (Bottom)
    • SMC_POST and SMC_PLL
  • Alternate SMC_PLL (Top, Southbridge)
    • Coronasmcpost.jpg
  • Alternate SMC_PLL (Top, DB2G3)
    • CoronaDB2G3.png

Postfix Adapter Installation & Identification Guide

  • Full Postfix Guide.png
Retrieved from "https://consolemods.org/wiki/index.php?title=Xbox_360:RGH/Solder_Points&oldid=43771"