NES:Famicom Disk System Glitching Sprites Fix: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
mNo edit summary |
||
(3 intermediate revisions by one other user not shown) | |||
Line 1: | Line 1: | ||
Certain combinations of Famicom and Famicom Disk System (FDS) RAM adapter units have an issue which causes sprites to appear glitchy due to interference on the | Certain combinations of Famicom and Famicom Disk System (FDS) RAM adapter units have an issue which causes sprites to appear glitchy due to interference on the cartridge slot pins. The issue seems to affect mostly Famicoms with an HVC-CPU-GPM-02 board revision, RAM adapters with boards marked "HVC-FMR-03" and some early "HVC-FMR-02" boards. This issue may also occur when using flash carts and homebrew carts that use 39SFxxx flash chips. Information for this guide was compiled from multiple sources.<ref>https://retro.supermegabyte.com/2018/07/23/fix-glitchy-famicom-disk-system-sprites/</ref><ref>https://www.famicomworld.com/forum/index.php?topic=10607.0</ref><ref>https://synt4x.org/blog/index.php/2018/01/19/glitchy-graphics-on-famicom-disk-system/</ref><ref>https://twitter.com/SuperZvesda/status/1639694888944951297</ref> | ||
<div class="inline-thumb"> | <div class="inline-thumb">[[File:FDS Glitching Sprites Before.png|thumb|Sprite issue affecting Mario.<br>Credit to Shane from [https://retro.supermegabyte.com/2018/07/23/fix-glitchy-famicom-disk-system-sprites/ SuperMegaByte].]] [[File:FDS Glitching Sprites After.png|thumb|After sprite issue fix.<br>Credit to Shane from [https://retro.supermegabyte.com/2018/07/23/fix-glitchy-famicom-disk-system-sprites/ SuperMegaByte].]]</div> | ||
[[File:FDS Glitching Sprites Before.png|thumb|Sprite issue affecting Mario.]] [[File:FDS Glitching Sprites After.png|thumb|After sprite issue fix.]] | |||
</div> | |||
{{br}} | {{br}} | ||
Line 9: | Line 7: | ||
The solution is to add resistors on the data pins of the FDS RAM cart unit, which fixes the interference. | The solution is to add resistors on the data pins of the FDS RAM cart unit, which fixes the interference. | ||
# Obtain a [https://www.arcadepartsandrepair.com/store/components/resistors/4-7k-ohm-resistor-network-9-pin-bussed-r1105/ 9-pin 4.7kohm resistor array]. | # Obtain a [https://www.arcadepartsandrepair.com/store/components/resistors/4-7k-ohm-resistor-network-9-pin-bussed-r1105/ 9-pin 4.7kohm resistor array]. | ||
#* Alternatively, you can use eight 4.7kohm resistors. | #* Alternatively, you can use eight 4.7kohm resistors and solder one end together. | ||
# Use electrical tape to line up the resistor array as shown and hold it in place. | # Use electrical tape to line up the resistor array as shown below and hold it in place. | ||
#: <div class="inline-thumb">[[File:FDS Glitching Sprites Fix.png|thumb|Credit to Shane from [https://retro.supermegabyte.com/2018/07/23/fix-glitchy-famicom-disk-system-sprites/ SuperMegaByte].]]</div>{{br}} | |||
# Bend the first pin of the resistor array upwards so that it doesn't make contact with anything on the board. | # Bend the first pin of the resistor array upwards so that it doesn't make contact with anything on the board. | ||
# Solder a wire between the first pin and ground. Example ground point shown in image | # Solder a wire between the first pin and ground. Example ground point shown in image above. | ||
# Solder pin 2 of the resistor array to pin 6 of the FDS RAM adapter. | # Solder pin 2 of the resistor array to pin 6 of the FDS RAM adapter. | ||
# Solder the remaining pins of the resistor array to the FDS RAM adapter pins. Pins 6-13 should all be | # Solder the remaining pins of the resistor array to the FDS RAM adapter pins. Pins 6-13 should all be connected to the resistor array. | ||
{{br}} | {{br}} | ||
== References == | == References == | ||
[[Category:NES]] |
Latest revision as of 06:05, 27 May 2024
Certain combinations of Famicom and Famicom Disk System (FDS) RAM adapter units have an issue which causes sprites to appear glitchy due to interference on the cartridge slot pins. The issue seems to affect mostly Famicoms with an HVC-CPU-GPM-02 board revision, RAM adapters with boards marked "HVC-FMR-03" and some early "HVC-FMR-02" boards. This issue may also occur when using flash carts and homebrew carts that use 39SFxxx flash chips. Information for this guide was compiled from multiple sources.[1][2][3][4]
Solution
The solution is to add resistors on the data pins of the FDS RAM cart unit, which fixes the interference.
- Obtain a 9-pin 4.7kohm resistor array.
- Alternatively, you can use eight 4.7kohm resistors and solder one end together.
- Use electrical tape to line up the resistor array as shown below and hold it in place.
- Credit to Shane from SuperMegaByte.
- Bend the first pin of the resistor array upwards so that it doesn't make contact with anything on the board.
- Solder a wire between the first pin and ground. Example ground point shown in image above.
- Solder pin 2 of the resistor array to pin 6 of the FDS RAM adapter.
- Solder the remaining pins of the resistor array to the FDS RAM adapter pins. Pins 6-13 should all be connected to the resistor array.