Xbox 360:RGH/RGH1.2: Difference between revisions
Jump to navigation
Jump to search
(Alt phat points mentioned) |
|||
| Line 21: | Line 21: | ||
===Falcon / Jasper=== | ===Falcon / Jasper=== | ||
[https://eletronicabr.com/uploads/monthly_2020_03/CLK.png.fa26a2a9ab244dfa81fd65933046b71d.png Alt CLK (recommended)] | |||
[https://www.realmodscene.com/uploads/monthly_2017_02/r8c2.jpg.27f454a5560ee21c759de9609a5d690e.jpg Alt top-side RST] | |||
[https://xbox-360-img.gamergen.com/regfix13_0355028000076246.jpg Alt top-side POST (requires scraping)] | |||
[https://cdn.discordapp.com/attachments/610257524108820491/640289576035942411/image0.jpg Alt top-side PLL (requires scraping)] | |||
====[[:File:Coolrunnerrevcrgh12.jpg|Coolrunner Rev A/B/C/D]]==== | |||
* A - PLL | * A - PLL | ||
* B - STBY_CLK (only if not using oscillator) | * B - STBY_CLK (only if not using oscillator) | ||
| Line 28: | Line 35: | ||
* D - RST | * D - RST | ||
====[ | ====[[:File:Cr3litergh12.jpg|CR3 Lite]]==== | ||
* A - PLL | * A - PLL | ||
* B - STBY_CLK (only if not using oscillator) | * B - STBY_CLK (only if not using oscillator) | ||
| Line 34: | Line 41: | ||
* D - RST | * D - RST | ||
====[ | ====[[:File:Matrixglitcherrgh12diagram.jpg|Matrix Glitcher]]==== | ||
* A - RST | * A - RST | ||
* B - POST | * B - POST | ||
| Line 40: | Line 47: | ||
* F - PLL | * F - PLL | ||
====[ | ====[[:File:Squirtrgh12installdiagram.jpg|Squirt]]==== | ||
* Squirt BGA 1.2: Disable the onboard 670pf and/or 480pf caps by removing R7 and R8 | * Squirt BGA 1.2: Disable the onboard 670pf and/or 480pf caps by removing R7 and R8 | ||
* Squirt Reloaded 2.X: remove R2 and connect STBY_CLK | * Squirt Reloaded 2.X: remove R2 and connect STBY_CLK | ||
| Line 46: | Line 53: | ||
* Don't use POST or RST tuners | * Don't use POST or RST tuners | ||
====[ | ====[[:File:X360acergh12phatinstalldiagram.png|X360ACE (V1/V2/V3), DGX]]==== | ||
* C - POST | * C - POST | ||
* D - RST | * D - RST | ||
Revision as of 11:26, 3 July 2023
RGH1.2 combines RGH1-like PLL slowdown with Glitch2 images to allow reliable glitching of Falcon/Jasper consoles with split CB (post 14699 kernel). RGH1.2 V2 ports this hack to Trinity/Corona consoles as well as fixing a few issues on Jaspers.
Equipment Needed
- A glitch chip:
- Coolrunner Rev A/B/C/D or CR3 Lite
- Matrix Glitcher
- Squirt BGA/Reloaded
- X360ACE V1/V2/V3
- X360ACE V4/V5/V3+ (Trinity/Corona only)
- DGX
- A PC running Windows Vista or later
- A soldering iron, solder, and flux (MG 835 recommended)
- Isopropyl alcohol (91% or higher recommended) and cotton swabs
- xFlasher 360, NAND-X, JR-Programmer, or Matrix Flasher
- J-Runner with Extras (Includes RGH1.2 V2 Matrix/Coolrunner Timings)
- RGH1.2 V2 Timing Files (X360ACE/Squirt chips only)
Glitch Chip Installation
Falcon / Jasper
Alt top-side POST (requires scraping)
Alt top-side PLL (requires scraping)
Coolrunner Rev A/B/C/D
- A - PLL
- B - STBY_CLK (only if not using oscillator)
- C - POST
- D - RST
CR3 Lite
- A - PLL
- B - STBY_CLK (only if not using oscillator)
- C - POST
- D - RST
Matrix Glitcher
- A - RST
- B - POST
- C - STBY_CLK (only if not using oscillator)
- F - PLL
Squirt
- Squirt BGA 1.2: Disable the onboard 670pf and/or 480pf caps by removing R7 and R8
- Squirt Reloaded 2.X: remove R2 and connect STBY_CLK
- Pinout follows written labels
- Don't use POST or RST tuners
X360ACE (V1/V2/V3), DGX
- C - POST
- D - RST
- E - STBY_CLK (only if not using oscillator version)
- F - PLL (22K ohm resistor required)
- Remember to remove the diode and connect 1.8V
Trinity / Corona
Close-up of PLL
Coolrunner Rev A/B/C/D
- B - STBY_CLK (only if not using oscillator)
- C - POST
- D - RST
- E - PLL (10K ohm resistor recommended)
CR3 Lite
- B - STBY_CLK (only if not using oscillator)
- C - POST
- D - RST
- E - PLL (10K ohm resistor recommended)
Matrix Glitcher (Corona)
- A - RST
- B - POST
- E - PLL (10K ohm resistor recommended)
Matrix Glitcher (Trinity)
- A - RST
- B - POST
- C - STBY_CLK
- E - PLL (10K ohm resistor recommended)
X360ACE (V1/V2/V3/V3+), DGX
- C - POST
- D - RST
- F - PLL (10K ohm resistor recommended)
X360ACE V4/V5
- A - RST
- B - POST
- C1 - CPU_CLK_DP
- C2 - CPU_CLK_DN
- D - PLL (10K ohm resistor required)
Squirt
- Squirt Reloaded 2.X: remove R2 and connect STBY_CLK or remove 100 MHz and add 48 MHz oscillator
- Use SCL pad for PLL
- Pinout follows written labels
- Don't use POST or RST tuners
Programming the Glitch Chip
- Plug the cable from your programmer into the chip programmer.
- If you are using an xFlasher, ensure the switch is set to
SPI. - CoolRunner: Slide switch to "PRG".
- If you are using an xFlasher, ensure the switch is set to
- Open J-Runner with Extras. Click "Program Timing File" in the upper left and select your console’s tab and the relevant radio button for RGH 1.2.
- Click "Program". When complete, unplug the cable from the glitch chip.
- Coolrunner: Set the switch back to "NOR".
X360ACE V4/V5/V3+
- xFlasher or other Gowin compatible programmer required in order to program these chips
- Programming Instructions
Decrypting the NAND
- Connect Ethernet and power on the console. The Coolrunner should blink once or more times, and then the console should start into XeLL RELOADED.
- Once XeLL finishes, it will display your CPU key and some other info. There is also an IP address.
- Enter the IP address into the box on the lower right of J-Runner and click "Get CPU Key". J-Runner will pull the info from the box, and decrypt the NANDs automatically.
Writing New NAND Image
- Power down the console, and connect your programmer to the motherboard.
- If you are using an xFlasher, ensure the switch is set to
SPI.
- If you are using an xFlasher, ensure the switch is set to
- In the upper right of J-Runner, ensure the
Glitch2radio button is selected. - Click "Create XeBuild Image". This will take a few moments.
- Click "Write NAND".
- Disconnect your programmer when the process completes.
- Boot the console several times and ensure it boots consistently. If not, make sure your wiring is clean and neat and avoids noisy area. Run the wires near the X-Clamps for best results.
- Return to the RGH main page and continue in the Cleaning Up section.