AV:RetroTINK-4K: Difference between revisions
No edit summary |
|||
| Line 1: | Line 1: | ||
==RetroTINK-4K GUI Map | ==RetroTINK-4K GUI Map== | ||
===Basic Setup | ===Basic Setup=== | ||
====Input Selection==== | |||
Front: | Front: | ||
Composite | Composite | ||
| Line 27: | Line 27: | ||
HDMI: | HDMI: | ||
====HDMI Output:==== | |||
====Scaling/Croppping==== | |||
Input Crop: | Input Crop: | ||
Left Trim: | Left Trim: | ||
| Line 46: | Line 46: | ||
Buffer: | Buffer: | ||
Length: | Length: | ||
====Image Processing==== | |||
Scanline: | Scanline: | ||
Function: | Function: | ||
| Line 68: | Line 68: | ||
Output Factor: | Output Factor: | ||
SMPTE 2048 PQ: | SMPTE 2048 PQ: | ||
Deinterlacer | ====Deinterlacer==== | ||
(Deinterlacer Setup) | (Deinterlacer Setup) | ||
Mode: | Mode: | ||
| Line 80: | Line 80: | ||
Offset: | Offset: | ||
System: | ====System:==== | ||
(System Setup) | (System Setup) | ||
On Screen Display: | On Screen Display: | ||
| Line 94: | Line 94: | ||
Check SD Card | Check SD Card | ||
===Advanced Setup:=== | ===Advanced Setup:=== | ||
RGB/Component ADC | ====RGB/Component ADC==== | ||
(RGB/Component ADC Setup) | (RGB/Component ADC Setup) | ||
Sampling Rate: | Sampling Rate: | ||
| Line 113: | Line 113: | ||
Phase: | Phase: | ||
Gain: | Gain: | ||
HDMI Receiver | ====HDMI Receiver==== | ||
Reciever | Reciever | ||
Decimation Factor: | Decimation Factor: | ||
| Line 122: | Line 122: | ||
Input RGB Range: | Input RGB Range: | ||
SDP Decoder | ====SDP Decoder==== | ||
(SDP Decoder Setup) | (SDP Decoder Setup) | ||
Gain/Balance | Gain/Balance | ||
| Line 141: | Line 141: | ||
H-Lock Speed: | H-Lock Speed: | ||
Standard: | Standard: | ||
Audio Input | ====Audio Input==== | ||
(Audio Setup) | (Audio Setup) | ||
Sampling | Sampling | ||
| Line 151: | Line 151: | ||
===Profiles:=== | ===Profiles:=== | ||
(Profiles) | (Profiles) | ||
Load Profile: | ====Load Profile:==== | ||
Load Default | Load Default | ||
Load From File | Load From File | ||
| Line 158: | Line 158: | ||
Save Current | Save Current | ||
Save As New | Save As New | ||
Assign Profile: | ====Assign Profile:==== | ||
Button 1: | Button 1: | ||
Button 2: | Button 2: | ||
| Line 173: | Line 173: | ||
Power Up: | Power Up: | ||
===Device:=== | ===Device:=== | ||
Status | ====Status==== | ||
System Status Page 1: | System Status Page 1: | ||
Video Source: CP Proc. (I assume CP Proc will change based on selection) | Video Source: CP Proc. (I assume CP Proc will change based on selection) | ||
| Line 203: | Line 203: | ||
System Status Page 2: | System Status Page 2: | ||
System Status Page 3: | System Status Page 3: | ||
Diagnostic Console | ====Diagnostic Console==== | ||
About | ====About==== | ||
Device: | Device: | ||
FW Version | FW Version | ||
Device ID: | Device ID: | ||
Revision as of 08:04, 19 August 2023
RetroTINK-4K GUI Map
Basic Setup
Input Selection
Front: Composite S-Video RCA: YPbPr RGsB CVBS on Green SCART: RGBS (75 ohm) RGsB YPbPr CVBS on Pin 20 CBVS on Green Y/C on Pin 20/Red HD-15: RGBHV RGBS RGsB YPbPr CBVS on Hsync CBVS on Green Y/C on Green/Red HDMI:
HDMI Output:
Scaling/Croppping
Input Crop: Left Trim: Right Trim: Top Trim: Bottom Trim: Vert. Pre-Scale: Scaler: Aspect Correction: Scaling Mode: Vert. Factor: Hori. Factor: Interpolation: Vert. Kernel: Hori: Kernel: Buffer: Length:
Image Processing
Scanline: Function: Strength: Modulation: Red Bleed: Red Convergence: Blue Convergence: Mask: Enable: Strength: Load from File: Select a Mask File: RGB Masks: Mono Masks: Horizontal Blur: Function: Boost: Gamma/Linear Light/HDR: Input Factor: Output Factor: SMPTE 2048 PQ: ====Deinterlacer==== (Deinterlacer Setup) Mode: Algorithm: Field Inversion: Motion Adaptive Settings: Sensitivity: Interpolator: Detector: Bob Settings: Offset:
====System:==== (System Setup) On Screen Display: Position: Auto-Off: Load Banner: Enable Debug OSD: Blanking Color: Red: Green: Blue: Firmware Update: Check SD Card
Advanced Setup:
====RGB/Component ADC==== (RGB/Component ADC Setup) Sampling Rate: Decimation Factor: Decimation Phase: Sub-Phase: Anti-Alias: Sync: SoG Threshold: Pre-coast: Post-coast: Gain: Pre-ADC: Red: Green: Blue: Auto Calibrate: Phase: Gain: ====HDMI Receiver==== Reciever Decimation Factor: Decimation Phase: Color Space: 4:2:2 Upsampler: CSC Mode: Input RGB Range:
====SDP Decoder==== (SDP Decoder Setup) Gain/Balance Brightness: Contrast: Chroma: Phase: Blue Only: Setup:
Processing: Y/C Filter: Comb Bandwidth: Chroma Bandwidth: Sharpness: CTIE: Sync: H-Lock Speed: Standard: ====Audio Input==== (Audio Setup) Sampling Sampling Rate: Pre-amp Gain: Source Input Override: Input Swap:
Profiles:
(Profiles) ====Load Profile:==== Load Default Load From File (opens file selector window titled "Select Profile") Save Profile: Save Current Save As New ====Assign Profile:==== Button 1: Button 2: Button 3: Button 4: Button 5: Button 6: Button 7: Button 8: Button 9: Button 10: Button 11: Button 12: Power Up:
Device:
====Status==== System Status Page 1: Video Source: CP Proc. (I assume CP Proc will change based on selection) Input Timing: Pixel Clock: Freq: Detected Mode: Audio Input: I2S (I assume will change based on audio input) Measured Freq: HDMI SR: HDMI N / CTS: FPGA Core Scaler Clock: PLL VCO: Pipeline: SDRAM Clock: SDRAM Load: HDMI Transmitter Output Timing: Active Size: Pixel Clock: HDMI Standard: PIC32MX MCU System Clock: Uptime: Loop Time: Last IR Code: SD Card Free: System Status Page 2: System Status Page 3: ====Diagnostic Console==== ====About==== Device: FW Version Device ID: