AV:RetroTINK-4K: Difference between revisions
| Line 68: | Line 68: | ||
Output Factor: | Output Factor: | ||
SMPTE 2048 PQ: | SMPTE 2048 PQ: | ||
====Deinterlacer==== | |||
(Deinterlacer Setup) | (Deinterlacer Setup) | ||
Mode: | Mode: | ||
| Line 80: | Line 80: | ||
Offset: | Offset: | ||
====System:==== | |||
(System Setup) | (System Setup) | ||
On Screen Display: | On Screen Display: | ||
| Line 152: | Line 152: | ||
===Profiles:=== | ===Profiles:=== | ||
(Profiles) | (Profiles) | ||
====Load Profile:==== | |||
Load Default | Load Default | ||
Load From File | Load From File | ||
| Line 159: | Line 159: | ||
Save Current | Save Current | ||
Save As New | Save As New | ||
====Assign Profile:==== | |||
Button 1: | Button 1: | ||
Button 2: | Button 2: | ||
| Line 174: | Line 174: | ||
Power Up: | Power Up: | ||
===Device:=== | ===Device:=== | ||
====Status==== | |||
System Status Page 1: | System Status Page 1: | ||
Video Source: CP Proc. (I assume CP Proc will change based on selection) | Video Source: CP Proc. (I assume CP Proc will change based on selection) | ||
| Line 204: | Line 204: | ||
System Status Page 2: | System Status Page 2: | ||
System Status Page 3: | System Status Page 3: | ||
====Diagnostic Console==== | |||
====About==== | |||
Device: | Device: | ||
FW Version | FW Version | ||
Device ID: | Device ID: | ||
Revision as of 08:05, 19 August 2023
RetroTINK-4K GUI Map
Basic Setup
Input Selection
Front: Composite S-Video RCA: YPbPr RGsB CVBS on Green SCART: RGBS (75 ohm) RGsB YPbPr CVBS on Pin 20 CBVS on Green Y/C on Pin 20/Red HD-15: RGBHV RGBS RGsB YPbPr CBVS on Hsync CBVS on Green Y/C on Green/Red HDMI:
HDMI Output:
Scaling/Croppping
Input Crop: Left Trim: Right Trim: Top Trim: Bottom Trim: Vert. Pre-Scale: Scaler: Aspect Correction: Scaling Mode: Vert. Factor: Hori. Factor: Interpolation: Vert. Kernel: Hori: Kernel: Buffer: Length:
Image Processing
Scanline: Function: Strength: Modulation: Red Bleed: Red Convergence: Blue Convergence: Mask: Enable: Strength: Load from File: Select a Mask File: RGB Masks: Mono Masks: Horizontal Blur: Function: Boost: Gamma/Linear Light/HDR: Input Factor: Output Factor: SMPTE 2048 PQ:
Deinterlacer
(Deinterlacer Setup) Mode: Algorithm: Field Inversion: Motion Adaptive Settings: Sensitivity: Interpolator: Detector: Bob Settings: Offset:
System:
(System Setup) On Screen Display: Position: Auto-Off: Load Banner: Enable Debug OSD: Blanking Color: Red: Green: Blue: Firmware Update: Check SD Card
Advanced Setup:
RGB/Component ADC
(RGB/Component ADC Setup) Sampling Rate: Decimation Factor: Decimation Phase: Sub-Phase: Anti-Alias: Sync: SoG Threshold: Pre-coast: Post-coast: Gain: Pre-ADC: Red: Green: Blue: Auto Calibrate: Phase: Gain:
HDMI Receiver
Reciever Decimation Factor: Decimation Phase: Color Space: 4:2:2 Upsampler: CSC Mode: Input RGB Range:
SDP Decoder
(SDP Decoder Setup) Gain/Balance Brightness: Contrast: Chroma: Phase: Blue Only: Setup:
Processing: Y/C Filter: Comb Bandwidth: Chroma Bandwidth: Sharpness: CTIE: Sync: H-Lock Speed: Standard:
Audio Input
(Audio Setup) Sampling Sampling Rate: Pre-amp Gain: Source Input Override: Input Swap:
Profiles:
(Profiles)
Load Profile:
Load Default Load From File (opens file selector window titled "Select Profile") Save Profile: Save Current Save As New
Assign Profile:
Button 1: Button 2: Button 3: Button 4: Button 5: Button 6: Button 7: Button 8: Button 9: Button 10: Button 11: Button 12: Power Up:
Device:
Status
System Status Page 1: Video Source: CP Proc. (I assume CP Proc will change based on selection) Input Timing: Pixel Clock: Freq: Detected Mode: Audio Input: I2S (I assume will change based on audio input) Measured Freq: HDMI SR: HDMI N / CTS: FPGA Core Scaler Clock: PLL VCO: Pipeline: SDRAM Clock: SDRAM Load: HDMI Transmitter Output Timing: Active Size: Pixel Clock: HDMI Standard: PIC32MX MCU System Clock: Uptime: Loop Time: Last IR Code: SD Card Free: System Status Page 2: System Status Page 3:
Diagnostic Console
About
Device: FW Version Device ID: