AV:RetroTINK-4K: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
Line 143: Line 143:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Scanline
! colspan="2" style="text-align:left;"|Scanline
|-
|-
| Function
| Function
Line 165: Line 165:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Mask
! colspan="2" style="text-align:left;"|Mask
|-
|-
| Enable
| Enable
Line 178: Line 178:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Horizontal Blur
! colspan="2" style="text-align:left;"| Horizontal Blur
|-
|-
| Function
| Function
Line 188: Line 188:
{| class="wikitable"  
{| class="wikitable"  
|-
|-
! colspan="2" | Gamma/Linear Light/HDR
! colspan="2" style="text-align:left;"| Gamma/Linear Light/HDR
|-
|-
| Input Factor
| Input Factor

Revision as of 08:56, 19 August 2023

RetroTINK-4K GUI Map

Basic Setup

Input Selection

Front
Composite information
S-Video information
RCA
YPbPr information
RGsB information
CVBS on Green information
SCART
RGBS (75 ohm) information
RGsB information
YPbPr information
CVBS on Pin 20 information
CBVS on Green information
Y/C on Pin 20/Red information
HD-15
RGBHV information
RGBS information
RGsB information
YPbPr information
CBVS on Hsync information
CBVS on Green information
Y/C on Green/Red information
HDMI
thing a information
thing b information

HDMI Output:

Scaling/Cropping

Input Crop
Left Trim information
Right Trim information
Top Trim information
Bottom Trim information
Vert. Pre-Scale information
Scaler
Aspect Correction information
Scaling Mode information
Vert. Factor information
Hori. Factor information
Interpolation
Vert. Kernel information
Hori. Kernel information
Buffer
Length information

Image Processing

Scanline
Function information
Strength information
Modulation information
Red Bleed information
Red Convergence information
Blue Convergence information
Mask
Enable information
Strength information
Load from File Select a Mask File, RGB Masks:, Mono Masks:
Horizontal Blur
Function information
Boost information
Gamma/Linear Light/HDR
Input Factor information
Output Factor information
SMPTE 2048 PQ information

Deinterlacer

(Deinterlacer Setup) Mode: Algorithm: Field Inversion: Motion Adaptive Settings: Sensitivity: Interpolator: Detector: Bob Settings: Offset:

System:

(System Setup) On Screen Display: Position: Auto-Off: Load Banner: Enable Debug OSD: Blanking Color: Red: Green: Blue: Firmware Update: Check SD Card

Advanced Setup:

RGB/Component ADC

(RGB/Component ADC Setup) Sampling Rate: Decimation Factor: Decimation Phase: Sub-Phase: Anti-Alias: Sync: SoG Threshold: Pre-coast: Post-coast: Gain: Pre-ADC: Red: Green: Blue: Auto Calibrate: Phase: Gain:

HDMI Receiver

Reciever Decimation Factor: Decimation Phase: Color Space: 4:2:2 Upsampler: CSC Mode: Input RGB Range:

SDP Decoder

(SDP Decoder Setup) Gain/Balance Brightness: Contrast: Chroma: Phase: Blue Only: Setup:

Processing: Y/C Filter: Comb Bandwidth: Chroma Bandwidth: Sharpness: CTIE: Sync: H-Lock Speed: Standard:

Audio Input

(Audio Setup) Sampling Sampling Rate: Pre-amp Gain: Source Input Override: Input Swap:

Profiles:

(Profiles)

Load Profile:

Load Default Load From File (opens file selector window titled "Select Profile") Save Profile: Save Current Save As New

Assign Profile:

Button 1: Button 2: Button 3: Button 4: Button 5: Button 6: Button 7: Button 8: Button 9: Button 10: Button 11: Button 12: Power Up:

Device:

Status

System Status Page 1: Video Source: CP Proc. (I assume CP Proc will change based on selection) Input Timing: Pixel Clock: Freq: Detected Mode: Audio Input: I2S (I assume will change based on audio input) Measured Freq: HDMI SR: HDMI N / CTS: FPGA Core Scaler Clock: PLL VCO: Pipeline: SDRAM Clock: SDRAM Load: HDMI Transmitter Output Timing: Active Size: Pixel Clock: HDMI Standard: PIC32MX MCU System Clock: Uptime: Loop Time: Last IR Code: SD Card Free: System Status Page 2: System Status Page 3:

Diagnostic Console

About

Device: FW Version Device ID: