AV:RetroTINK-4K: Difference between revisions

Revision as of 15:29, 18 November 2023

The RetroTINK-4K is an advanced video scaler from Mike Chi / RetroTINK LLC. Building on the functionality of the RetroTINK-2X and RetroTINK-5X, the RetroTINK-4K offers high-end video scaling and processing at resolutions up to 4K/60hz.

RetroTINK-4K User's Manual

Overview

The RetroTINK-4K is the latest evolution of the RetroTINK line of video line doublers and upscalers. Below is a list of some standout features:

Output

Digital Video up to 4K60 at 8 bits
HDR10 output with full color correction to Rec. 2020
High frame rate output modes: 1440p120, 1080p240
Up to 8-ch LPCM audio
Supports user-defined custom modelines on the SD card

Inputs

Supports for virtually all analog formats:
- HD15/VGA: RGBHV, RGBS, RGsB, YPbPr, S-video and Composite
- SCART: RGBS, RGsB, YPbPr, S-video and Composite
- Rear RCA: RGsB, YPbPr and Composite
- Front Composite
- Front S-Video
Digital Video Input supporting up to 1080p60
Analog audio input sampled at up to 96kHz/24-bit
Optical TOSLINK audio input supporting 2-Ch LPCM or compressed surround
Digital Video audio supports up to 8-ch LPCM

Analog Video

Automatic gain calibration
Automatic phase calibration
Automatic input cropping to trim borders
Full control of gain, offset and sample rate
Console specific automatic sample rate detection (experimental feature)
Support for a wide variety of off-spec arcade and PC boards (may require custom profiles to properly trim and center the image)

Scaling

Fully flexible, custom cropping and zooming in the horizontal and vertical space independent of other settings
Automatic aspect ratio correction to 4:3 or 16:9
Motion adaptive deinterlacing including film modes for 3:2 and 2:2 inverse telecine (experimental feature)
RoTATE 90 deg CW or CCW (for 240p, 288p and 360p inputs)

Image Processing

End to end RGB pipeline with 12-bit precision (truncated to 8 or 10 bits for final output)
Optional linear light mode
Advanced CRT simulation modes with multiple scanline beam patterns and masks
Black frame insertion engine with customizable pattern and intensity
Advanced color correction supporting custom matrices for RGB to XYZ conversion

User Interface

Advanced OSD menu based system
SD Card for saving profiles, custom modelines and firmware updates
Custom premium remote control

Alternatives

The RetroTINK-4K is a premium product designed for high-end analog and digital video upscaling. It may be insightful for some users to compare the 4K's feature set to its sister product, the RetroTINK-5X. The table below emphasizes some key improvements and features the 4K to its predecessor.

RetroTINK-4K Versus RetroTINK-5X Feature Comparison
Feature	RetroTINK-4K	RetroTINK-5X
Max Output	4K60hz	1080p60hz (1440p experimental)
Black Frame Insertion	Yes	No
High Framerate Output	Yes (1080p120hz)	No
Digital Video Input	Yes	No (requires digital to analog transcoding, limited support)
Lanzcos Scaling	Yes	No
1080p Input	Yes (Digital / YPbPr)	No, 1080i max input over YPbPr (limited support)
VGA Input	Yes / Fully Supported	No (requires VGA to SCART solution) / limited support
RGsB Input	Yes	No
Linear Light Reproduction	Yes	No
Rotation	Yes via RoTATE	No
HDR	Yes	Yes* (less than accurate color reproduction)
Digital Audio In	Yes	No
Automatic Phase	Yes	Yes
Automatic Gain	Yes	No (requires manual calibration)
Native RGB Processing	Yes	No (YPbPr conversion pipeline)
Customizable Shadow Masks	Yes (loaded from SD)	No (Hard Coded from Firmware)
Profile Slots	1,000+	10
Transferable Profiles	Yes (SD card file system)	No (manual entry profile slots)
Automatic Resolution Detection	Yes	No
Color Space Conversion (CSC)	Yes	No
Firmware Updates	SD card file update	Requires connection to PC with FW update software
Non-Integer Scanline Support	Yes	No (scanlines require integer scaling to function properly)
Advanced MA Deinterlacing	Yes (1080i, Customizable)	No (480i max, no customization)
480i/240p Downscaling	Possible but Unsupported	Yes
Smoothing Filter	No	Yes (Smooth vertical interpolation)

Getting Started

Here are some steps to get started Using the RetroTINK-4K:

Video Output: Connect a digital video cable (2.0 or higher / 18Gbps+) from the RetroTINK-4K output to your display.
Video Input: Connect your device's signal to any of the RetroTINK-4K's inputs. More information on supported connections can be found in the Inputs section.
Supply Power: Connect a USB-C cable supplying at least 2A to the USB-C power input on the 4K.
Confirm Video: By default, the RetroTINK-4K outputs 4K60. If you don't see any picture, confirm that your display supports 4K60, or press the button on the remote that matches the resolution of your display (1080p, 1440p, or 480p). See the Remote and Output sections for more information.
Select Your Input: Once you see the 4K's splash screen on your display, you will need to select your input. To do this, use the remote to navigate through the Input selections and choose the port and signal your device is using.
Enjoy: Once your video source is visible, that is it! Enjoy the high quality, low latency scaling of the RetroTINK-4K.

Of course, there is a lot more you can do from here. Some options to explore: (these will be links to fleshed out sections of the wiki)

Choose an Expert-Crafted Optimal Profile
Tweak picture Alignment / Scaling
Customize CRT and Scanline Effects
Improve Image Vividness with HDR
Improve Motion Clarity With Black Frame Insertion

As well as many other adjustments, tweaks and possibilities for image manipulation to explore documented throughout this wiki.

Inputs

The RetroTINK-4K features inputs for a wide variety of signals and connector types.

Front

The Tink 4K offers S-Video (over Mini-Din) and Composite (over RCA) inputs in the front. The red and white RCA jacks are stereo audio inputs. Red/White front audio inputs are active when either the Front Composite or S-Video input is selected (assuming audio input override is not used).

Front Inputs
	Composite	To use composite video, use the yellow RCA jack for video (CVBS/Composite) and the Red/White RCA jacks for right and left audio input, respectively.
	S-Video	To use composite video, Mini-Din for video (Y/C S-Video) and the Red/White RCA jacks for right and left audio input, respectively.

Rear RCA

The rear RCA jacks support YPbPr (component), RGsB, and CVBS (composite) inputs.

Rear RCA Input
	YPbPr	To use YPbPr (Component Video), connect the Red, Green and Blue YPbPr video cables to their corresponding colored RCA connectors, noting that the Red/White pair to the left is for stereo audio input. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	RGsB	The Rear RCA input also supports RGsB, a flavor of RGB that sends the sync alongside the Green signal. To use RGsB (aka RGB Sync on Green), connect the Red, Green and Blue RGsB signals to their corresponding colored RCA connectors, noting that the Red/White pair to the left is for stereo audio input. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	CVBS on Green	Composite video (CVBS) can be used with the Rear RCA input. To use CVBS, connect the composite signal connector to the Green RCA jack. The Red/White pair of jacks furthest left is for stereo audio input. The maximum supported resolution is 480i.

SCART

SCART Input
	RGBS (75 ohm)	RGBS is a form of RGB where sync is sent through a discrete line. The TINK 4k accepts the following RGBS signal formats via SCART: Composite Sync (attenuated), Sync-on-Luma, and Sync-on-composite. They all work by sending information down the Red, Green, Blue, and "Sync" lines. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	RGsB	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via SCART. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	YPbPr	YPbPr is sent through the Green, Blue, and Red pins, respectively. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	CVBS on Pin 20	Composite video sent through Pin 20. If you use a composite/s-video scart adapter, composite will go down this line. (sic) The maximum resolution supported is 480i.
	CBVS on Green	Composite video can be sent through the Green pin. This would be useful if you use a component (YPbPr) to SCART adapter, just plug composite (yellow) into the Y RCA jack (Green). The maximum resolution supported is 480i.
	Y/C on Pin 20/Red	S-Video (Y/C) is broken out into 2 pins, Green and Red. This is useful if you wish to connect S-Video with a SCART Switch using an adapter. The maximum resolution supported is 480i.


Pin #	RGBS (75 Ohm)	RGsB	YPbPr	CVBS on Pin 20	CBVS on Green	Y/C on Pin 20/Red
1	Unused
2	Audio In - Right
3	Unused
4	Ground
5	Ground
6	Audio In - Left
7	Blue	Blue	Pb
8	Unused
9	Ground
10	Unused
11	Green	Green+Sync	Y		CVBS
12	Unused
13	Ground
14	Unused
15	Red	Red	Pr			Chroma (C)
16	Unused
17	Ground
18	Ground
19	Unused
20	Sync			CVBS		Luma (Y)

HD-15

HD-15 Input
	RGBHV	RGBHV is a form of RGB where information is sent through 5 lines: Red, Green, Blue, Horizontal Sync, and Vertical Sync. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	RGBS	RGBS is a form of RGB where sync is sent through one line, instead of two. The Tink 4k HD-15 connection supports these forms of RGBS: Composite Sync, Sync-on-Luma, and Sync-on-composite. They all work by sending information down the Red, Green, Blue, and "H-Sync" lines. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	RGsB	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via RGB. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	YPbPr	YPbPr is sent through the Green, Blue, and Red pins, respectively. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz
	CBVS on Hsync	Composite video sent through the HSync pin ofthe HD-15 connection. If you use a composite/s-video scart adapter, composite will go down this line. (sic) The maximum resolution supported is 480i.
	CBVS on Green	Composite video can be sent through the Green pin. This would be useful if you use a component (YPbPr) to VGA adapter, just plug composite (yellow) into the Y RCA jack (Green). The maximum supported resolution is 480i.
	Y/C on Green/Red	S-Video (Y/C) is broken out into 2 pins, Green and Red. This is useful if you wish to connect S-Video with a VGA Switch using an adapter. The maximum supported resolution is 480i.


Pin #	RGBHV	RGBS	RGsB	YPbPr	CBVS on Hsync	CBVS on Green	Y/C on Green/Red	Data
1	Red	Red	Red	Pr			Chroma(C)
2	Green	Green	Green+Sync	Y		CVBS	Luma(Y)
3	Blue	Blue	Blue	Pb
4	Unused
5	Ground
6	Ground
7	Ground
8	Ground
9	Unused
10	Ground
11	Unused
12								External Transmit (EXT TX)
13	Horizontal Sync	Sync			CVBS
14	Vertical Sync
15								External Receive (EXT RX)

Digital Video

Digital Video Input
	The Tink 4k supports many resolutions digitally up to 1080p 60fps (10Gbps) via its Digital Video line.

3.5mm TRS Audio

3.5mm TRS Audio
	The RetroTINK 4k-Pro allows for audio through a 3.5mm TRS input. This accepts stereo audio sound.

Optical Audio

Optical Audio
	The RetroTINK 4K-Pro offers a discrete optical audio Toslink input. This input 2-channel LPCM and compressed surround sound.

Alternate Audio Inputs

You can override the audio from any analog source over all video sources in the RetroTINK 4k-Pro. Make your way to the Advanced Settings, select "Audio Input" under "Acquisition" and make your way to the "Input Override" option under "Source" and select the audio source you want to use. The only exception is you cannot override an analog video source with audio from Digital Video. All other combinations work. Here's a brief description of the different possible audio sources for this option:

Audio Input Override Sources
Picture	Name	Description
	RCA (Rear)	The leftmost two RCA inputs in the rear. White and Red,
	HD15	The 3.5mm TRS input in the rear.
	SCART	The SCART input on the side. Audio is fed in through pins 2 and 6.
	Front	The red and white RCA inputs in the front of the unit.
	SPDIF	Optical audio fed through a Toslink input.

Output

The RetroTINK 4K-Pro only outputs via the Digital Video output port. It does not output through any of its analog ports and this functionality will not be added at a later time.

Output Resolutions

The following outputs are readily supported by the RetroTINK 4K-Pro. Also noted are resolutions available by pushing their respective button on the remote. If you are unsure which resolution to use, use the buttons on the remote.

TINK 4K Output Resolutions
Resolution	Description	Remote Button?
4k60	Default resolution and framerate for 4k displays, aka 3840x2160p. Default Resolution for the TINK 4K-PRO	Yes
4k50	Intended for PAL games and 24Hz content.	No
1080p60	Default resolution for 1080p displays.	Yes
1080p50	Intended for PAL games. and 24Hz content	No
1440p60	Default resolution and framerate for 1440p monitors, aka 2560x1440p.	Yes
1440p50	Intended for PAL games and 24Hz content	No
1080p100	Intended for PAL games and 24Hz content with BFI	No
1440p100	Intended for PAL games and 24Hz content with BFI	No
1080p120	Intended for NTSC content with BFI	No
1440p120	Intended for NTSC content with BFI	No
480p60	Minimum suggested output resolution for modern displays, aka 720x480p. Pressing the Reset button on the back of the unit activates this resolution.	Yes
2880x2160p70.00	Intended for off spec content from retro computers	No
1920x2160p60.00		No
800x600p60.00	Output for retro computers.	No
1920x1200p60	5x output for consoles intended for 8:5 (16:10) displays.	No

Remote


Button	Description	Button	Description	Button	Description
Power	Powers on / off the Tink 4K	11	Profile 11	4K	Switches to 3840x2160p 60Hz
INPUT	Input Source Selection Menu	12	Profile 12	1080p	Switches to 1920x1080p 60Hz
OUT	Digital Video Output menu	MENU	RetroTINK-4K Main Menu	1440p	Switches to 2560x1440p 60Hz
SCL	Scaling/Crop Setup	BACK	Back button	480p	Switches to 720x480p 60Hz
SFX	Image Processing	△	Up	RES1	Custom Output Resolution 1
ADC	Enters Acquisition menu matching the current input	◁	Left	RES2	Custom Output Resolution 2
PROF	Profiles	ENTER	Enter	RES3	Custom Output Resolution 3
1	Profile 1	▷	Right	RES4	Custom Output Resolution 4
2	Profile 2	▽	Down	AUX1
3	Profile 3	DIAG	Diagnostic Console	AUX2
4	Profile 4	STAT	Status	AUX3
5	Profile 5	AUTO-GAIN	Auto Calibrate Gain	AUX4
6	Profile 6	AUTO-PHASE	Auto Calibrate Phase	AUX5
7	Profile 7	PLAY/PAUSE	Pause current screen	AUX6
8	Profile 8	SAFE		AUX7
9	Profile 9	SYNC-GEN	Sync Lock Gen	AUX8
10	Profile 10	SYNC-BUF	Sync Lock Triple Buffer	-

Scaling/Crop

The RetroTINK-4K has robust controls to adjust size, positioning and cropping. For most users, the CP Auto Crop function will trim the unused area

Profiles

Profile Management

Included Profiles

Community Profiles

Profile Troubleshooting

Advanced Settings

Automatic Settings

Automatic Sampling Detection

The RetroTINK 4k can take advantage of sampling and scaling algorithms to seamlessly change settings when it detects a horizontal resolution change. This is useful for most analog retro gaming consoles, but requires knowledge of their "Master Sampling Rate," noted below.

Master Sampling Rate Chart
Console Name	Master Sampling Rate	Available Resolutions
Super NES	3410	256x224, 256x239, 512x224
Sega Genesis/Mega Drive		256x224, 320x224
Sega Saturn
Turbo Grafx 16/PCEngine	2730	256x224, 320x224
Sony Playstation		256x224, 320x224, 384x224, 512x224, 640x224
Sony Playstation 2

Once you know the master Sampling rate of your console, set that console's ADC Sample rate in the "Sample Rate Detection" menu under ADC Sample Rate, and turn both "Auto Dec. Factor" and "Auto Dec. Phase" to "On." Once you enable those options, if you know which resolutions you'll use, scroll down to that resolution to enable that horizontal resolution's detection and the RetroTINK 4K-Pro should automatically switch to a different set of settings whenever it detects that particular resolution is used. This process will help automatically set Decimation Factor and Decimation Phase in the ADC setup.

Automatic Color Calibration

For RGB and YPbPr sources ONLY. If you are able to find a sufficiently large patch of color that should be white in your game screen, make your way to the RGB/Component Setup page (click the ADC button on the remote) and make your way down to the "Auto Calibrate" option. Selecting this makes the RetroTINK 4K-Pro automatically calibrate your color based on that white patch. You may need to manually adjust the individual colors a few ticks more to get the true RGB code 255,255,255 for a color.

Automatic Phase

Any game screen is sufficient for automatic phasing, but it is recommended to use the 240p Test Suite or other sufficiently patterned screen for eyeballing results. whether you've set automatic sample detection using that menu, or you manually selected Decimation Factor in the ADC page, selecting Auto-Calibrate Phase makes the RetroTINK 4K-Pro automatically select the best Decimation Phase and Sub-Phase for your current picture and should give you the sharpest results. It is recommended you run this 3-5 times to make sure the same factors and phases are consistently chosen.

CP Auto Crop

The RetroTINK 4K-Pro can automatically crop and set aspect ratio for an input if it is fed a sufficient game screen. Letterboxed, pillar-boxed, and window-boxed screens are not recommended. Please see what the options do below:

CP Auto Crop Settings
Name	Effect
Vertical Only	Automatically adjusts "Top Trim" and "Bottom Trim" to the top and bottom of the game image. Does not adjust Left Trim or Right Trim, and does not change Aspect Correction
Full Crop to 4:3	Automatically adjusts Left, Right, Top, and Bottom Trim to the image, and changes Aspect Correction to 4:3 (PAR)
Full Crop to 16:9	Automatically adjusts Left, Right, Top, and Bottom Trim to the image, and changes Aspect Correction to 16:9 (PAR)

Image Scaling

Console Specific Methodology

Nintendo NES/Famicom

The NES renders games in 256x224p. A stock NES, model number NES-001, supports composite, while most other NES consoles support RF. You will need at least a composite signal to connect with the RT4K.

NES renders and outputs all audio in mono. To get correct stereo into the RT4K, you will need to use a female-to-dual-male RCA splitter, and connect both male ends to the stereo audio inputs of the RT4K.

Super NES/Super Famicom

The majority of Super NES games run in 256x224 resolution, while a select few games run with a mix of the following: 512x224 in the whole screen for menus, 256x224 for most of the image while running 512x224 over certain parts of the screen to create transparency effects, or the same but using 512x224 resolution to get sharper text on the screen. It is recommended to run the Super NES in 512x224p mode to make sure you get all available detail. (https://consolemods.org/wiki/AV:RetroTINK-5X_Pro#512_%22Hi_Res%22_Games)

We recommend using a Super NES model number SNS-001 or Super Famicom model number SHVC-001 and an RGB SCART cable wired for Sync-on-Luma, as this works with both of the aforementioned models. There are internal revisions of these models, noted as "1-Chip" on the motherboard, and the 1-Chip-03 does not work with Composite Sync. There is a revised model, SNS-101 and SHVC-101, also known as the Super Nintendo Junior. This model only supports composite video.

[Picture Here: 1-Chip without gain adjustments vs 1-Chip with gain adjustments]

As noted, there are revisions of the original model Super NES, noted by the "1-chip" on the motherboard. The 1-chip boards have sharper yet brighter video, while the non-1-chip boards have a "smudged" and slightly darker look. We encourage using the auto-gain functions in the ADC to correct the video on both models.

[Picture Here: Non-1-Chip vs 1-Chip]

Profile included for automatic switching between 512 and 256 in Display Aspect Ratio, for both SCART and HDRV YPbPr cables.

Super GameBoy

The Super GameBoy Cartridge allows you to play original style GameBoy and GameBoy Color cartridges on your TV using the Super Nintendo, and adds borders. Once dialed in, GameBoy games are rendered in a 160x144p window inside a 256x239p canvas.

[Picture Here: Generic SGB vs Optimized 15x]

Profile included to maximize the GameBoy window to the screen.

N64

All stock N64 support Composite, all NTSC N64 support S-Video, some PAL N64 do not support S-Video, and French N64 support SECAM S-Video.

All N64 have 3 levels of video processing that keeps it from being sharp:

All games scale their image to 640 pixels wide. Many games were rendered at different resolutions but the N64 will scale to 640.
- Many games render at 320 pixels wide and, as a trick, you can double your ADC Decimation factor to "correctly" render games in their original resolution. This trick only works for games that render at 320 pixels wide, and do not work for games that render at other resolutions that are not 320 or 640 pixels wide.
Software level anti-aliasing. This can be disabled by patching ROMs or using a Gameshark to disable the effect.
Hardware level anti-aliasing. This can't be disabled without a physical mod.

[Picture Here: AA enabled vs AA disabled]

[Picture Here: a 320 game with the trick used vs left at 640 (should be the same)]

[Picture Here: a non-640 or 320 game with the trick used (should look worse)]

Pokemon Stadium GameBoy Tower

Pokemon Stadium's GameBoy Tower allows you to play Pokemon games on your TV, just like a Super GameBoy. It also uses borders just like the Super GameBoy. The issue, however, is the scaling noted above. These games render at 160x144p inside a 256x239p canvas, which is then scaled to 640 pixels wide. You will not get a sharp picture out of this setup due to that factor alone. It is recommended to play in a generic or default profile.

[Picture Here: SGB vs Pokemon Stadium]

Nintendo GameCube

For the purposes of use with the RetroTINK 4K-Pro, it is highly recommended to use a DOL-001 GameCube, which has the digital out port, and an Insurrection Industries Carby, which outputs crisp digital video and can connect to the Digital Video input port of the RT4K. If you insist on buying YPbPr cables, we can only recommend the OEM D-Terminal cable with a D-Terminal to Component adapter, or the OEM component Cable.

Most GameCube Games will run at 480p, and that progressive mode is activated by holding B when the GameCube boots up a game.

Swiss, the Anti-Flicker Filter, and Horizontal Frame buffer Width

While Most GameCube games run at 480p and progressive mode is relatively easy to access, many GameCube games use an "anti-flicker-filter" by default, which will soften the image. Most of these filters can't be turned off in-game, but the homebrew software Swiss will allow you to boot games, including your own disks, with the anti-flicker filter turned off. As an added bonus, newer versions of Swiss automatically turn the filter off and boot your game in 480p.

[Picture Here: game with anti-flicker filter on vs off]

[Video here: Smash Bros Melee turning the flicker filter on and off]

A few GameCube games scale their image to fit the console's frame buffer before output. Swiss allows you to turn this off and shows the image at its original framebuffer width, and you can use the RT4K to scale it back, for a small sharpness gain.

[picture here: Framebuffer width left alone and the framebuffer width option turned on, with the RT4K used to scale back to the intended resolution] (I don't know what game to use)

240p Games

There are 2 GameCube games that run at 240p: Megaman X Collection, and the NES games in the Zelda Collector's Edition Promotional Disc. This means you do not have to enable 480p to run those games and can sharply scale these games on the RT4K.

[Picture Here: Megaman X on Super NES vs GameCube]

GameBoy Player + GameBoy Interface

The GameBoy Player is a popular add-on to the GameCube that allows you to play GameBoy, GameBoy Color, and GameBoy Advance games on your TV. The GameBoy Player Disk does not sharply render games onto the screen, but you can use the homebrew software GameBoy Interface to sharply render games into the RT4K. A specific flavor of GBI was created to take advantage of the Insurrection Industries Carby and the TINK 4K's Digital Video input. Please use files gbihf-rt4k-HDMI.cli, gbihf-rt4k-HDMI.dol+cli or gbihf-rt4k-HDMI.gci included with GBI and follow the instructions noted here.

[Picture Here: GBA game on RT5x scaled to 4k (12x scale) vs RT4K (13x scale)]

[Picture Here: GBC game on RT5x scaled to 4k (12x scale) vs RT4K (15x scale)]

Profiles included for 13x scaled GBA games and 15x scaled GBC games.

Nintendo Wii

The Nintendo Wii is a very versatile console: it plays GameCube Games, Wii Games, and many classic retro titles through emulators as part of the Virtual Console lineup. The Wii has easy to find YPbPr component cables and can easily support 480p across all Wii software through its component cables. The Wii only supports 3 resolutions: 720x240p, 720x480i, and 720x480p. Please read on for more information on getting the sharpest possible picture from a Wii.

Profile included for basic generic output. It is recommended you use this for basic Wii use.

Virtual Console

Many Virtual Console games output at 240p when the Wii is in SDTV mode, and they will line double to output at 480p in EDTV mode. All virtual console games scale the image to 640 pixels wide, so it is recommended you use the default or generic profiles for playing virtual console games. Also of note: NES Virtual console games are rendered many shades darker than an orignal console, as an anti-epilepsy measure.

[Picture Here: Donkey Kong on Super NES vs Donkey Kong on Wii with generic settings]

USBLoader GX, and Counteracting the Anti-Flicker Filter, 480p LPF, and the Framebuffer Video Width

Homebrew called USBLoader GX allows you to activate or deactivate code before running games, even on your disks.

Most Wii games will apply an anti-flicker filter, even at 480p, which results in a softer picture. Use USBLoader GX's options to turn this off for Wii Games. If you wish to run GameCube games, you will need to turn the anti-flicker filter off separately in either Nintendont or Devolution, but USB-Loader GX does have these options in its menu.

[Video here: Super Smash Bros Brawl's settings menu turning the anti-flicker filter on and off]

There is an option in USBLoader GX called the "480p pixel fix" which makes the game look much sharper. It only works with RVL-001 models with the internal CPU-01 motherboard.

[Picture here: Wii game with 480p pixel fix off vs on]

You can get even sharper picture from the Wii by enabling the "Video Width: Framebuffer" option in USBLoader GX. This will make games output in their original rendering resolution, which you can then rescale using the RT4K to get a much sharper picture than originally intended at the "correct" aspect ratio. As an added bonus, NES and Super NES games will render at 512x224p with this option turned on, which you can use a doubled decimation factor to treat a game like its original 256x224 resolution, and get picture on par with their original consoles.

[Picture Here: Megaman X Super NES Optimal vs Wii Optimal]

Nintendo WiiU

Please use the WiiU's HDMI output. Please also note the WiiU's HDMI outputs in limited range, so please change that in the HDMI Receiver Setup Menu.

Nintendo Switch

NSO Games

it is highly recommended to use 1080p output for the NSO emulators and turning on "Pixel Perfect" in their settings under "Game Screen" and to also turn off "Show controls in game" under "Control Display," and to turn off "reproduce classic feel" on the GameBoy and GameBoy Advance apps. This way, all games output a perfectly integer scaled, line-multiplied output for their games.

[Picture here: Donkey Kong Country Super NES Optimal vs Switch Optimal vs Switch no adjustments] For a 256 wide game

[Picture here: Ristar Genesis on Wii Optimal vs Switch Optimal vs Switch no adjustments] for 320 wide games

[picture here: Mario & Luigi Superstar Saga on GBI 13x vs Switch Optimal 13x vs Switch no Adjustments 12x] for GBA games

[Picture Here: The Legend of Zelda, Oracle of Ages on GBI 15x vs Switch Optimal 15x vs Switch no adjustments 14x] for GBC games

Sega Master System

Recommended output: RGB

Sega Genesis/Mega Drive

Recommended output: RGB

Composite effects. see this portion of the 5x wiki https://consolemods.org/wiki/AV:RetroTINK-5X_Pro#Genesis_Dithering

Sega CD

Sega 32x

Master System Games on Genesis

Sega Saturn

Recommended output: RGB

Sega Dreamcast

Recommended Output: RGBHV

Sony PlayStation

All Sony Playstation models support RGBS. It is recommended to use a well shielded SCART cable that uses Sync-on-Luma.

Resolution Switching

PlayStation games will switch resolutions often, usually horizontal resolutions, but occasionally vertical resolutions as well. The PlayStation is a perfect use for the Automatic Sampling Detection feature of the RT4K. To help with switching vertical resolutions quickly, please enable Triple Buffer in the RT4K's Output menu.

see this part of the 5x wiki https://consolemods.org/wiki/AV:RetroTINK-5X_Pro#Resolution_Switching

Profiles included will automatically switch to all resolutions. You may want to consider looking through your game collection and see if you can turn off any resolutions that you won't use, for faster response from the auto sampling detection.

Sony PlayStation 2

The PS2 outputs 240p, 480i, 480p, and 1080i and supports RGB as well as YPbPr. For simplicity, it is highly recommended to use YPbPr cables because the RT4K will automatically detect and switch to all those resolutions seamlessly. The PS2 will use RGBS for 240p and 480i, but will switch to RGsB for any resolutions above that. While the RT4K supports RGsB, it does not automatically switch from RGBS to RGsB, you will need to change the input manually.

All PS2 games will output either 512 pixels wide or 640 pixels wide. [sic]

PS1 Backwards Compatibility

PS1 games on PS2 use a different set of optimal sampling numbers than the PS1 console.

Sony PlayStation Portable

PSP models PSP-2000, PSP-3000, and PSP-N1000 (aka PSP GO) can output to a display, and it is highly recommended to use component cables with the RT4K.

PSP games are rendered at 480x272p. When they are displayed on a television with component cables, they render a 480x272p picture inside of a 720x480p canvas. You can use the RT4K to upscale the image to fit the screen. You will cut off 2 vertical pixels at the expense of the sharpest picture

[Picture here: PSP left alone (4.5x scale) vs PSP scaled to 8x]

Playstation Classics

PlayStation Classics are PS1 games played on the PSP. You can render these games in their original resolution by enabling interlaced output in the display settings.

[picture here: ps1 console optimized vs ps1 classic]

Sony PlayStation 3

The PS3 supports HDMI and it is recommended to use that for the sharpest possible picture with the RT4K. While the PS3 does support up to 1080p using YPbPr, the standard is put to its limits and doesn't provide a picture as sharp as HDMI.

PS3 will automatically switch games to their highest automatically supported and selected resolution and the RT4K supports all inputs the PS3 supports.

[Picture Here: HDMI vs YPbPr]

PS1 Classics

PS1 games render in 480p, but scale the image to 4:3 aspect ratio. For the sharpest picture, it is recommended to turn off "PS Upscaling" in the PS3's settings and to use prescale 1/2 in the RT4K's Scaling/Crop Menu.

[Picture Here: PS1 console optimized vs ps1 classic]

Sony Playstation TV

The PSTV allows you to play Vita, PSP, and PS1 Classics on your TV through HDMI. By default, all output from the PlayStation TV is soft because of the following factors:

All software has a bilinear filter applied
All software is scaled to the PSTV's selected output resolution
Vita software is internally scaled to 960x544p regardless of its original rendering resolution. This applies to Vita handhelds as well
PS1 Classics are unevenly, horizontally scaled to 4:3.

To counteract this for the sharpest possible picture, we highly recommend installing custom firmware on your PSTV and installing the Sharpscale plugin to counteract all the above effects applied to the PSTV.

Sharpscale plugin

See an overview of sharpscale here. The following suggestions only work when sharpscale is enabled with the following options:

[picture of sharpscale plugin with the following settings enabled]

PSTV Sharpscale Options
Option Name	Option Choice
Scaling Mode	Integer
PS1 Aspect Ratio	Pixel
Scaling Algorithm	Point
Unlock Framebuffer Size	Off

Vita Games

When Playing a Vita Game, the PSTV outputs a 960x544p picture inside of a 1280x720p canvas. Use the following settings to get the sharpest integer scaled picture for Vita Games. These settings cut off 4 vertical pixels from Vita games.

RT4K PSTV Vita Settings
Scaling/Crop Setup
Top Trim	-90
Bottom Trim	-90

[Picture Here: Steamworld Dig 2 with sharpscale disabled vs enabled and optimized]

PSP Games

The PSTV also outputs a 960x544p picture inside of a 1280x720p canvas. Use the following settings to get the sharpest integer scaled picture for PSP games. These settings cut off 2 vertical pixels from PSP games.

RT4K PSTV PSP Settings
HDMI Receiver Setup
Input Pixels	2
Scaling/Crop Setup
Top Trim	-45
Bottom Trim	-45
Vert. Pre-Scale	1/2

[Picture Here: Final Fantasy IV with sharpscale disabled vs enabled and optimized]

PS1 Classics

Sharpscale will allow you to get the sharpest picture for ps1 games, but the behavior is not optimal. With the Integer Scaling Mode setting enabled in Sharpscale, some resolutions will use the full vertical space, and others will only scale to 480 vertical pixels inside 720p. it is recommended you look at the resolutions supported by your game before you use sharpscale with the RT4K and see if it is worth avoiding the headache. If you set PS1 Aspect Ratio to 4:3, the PSTV will force all games to fit, but they will not evenly scale horizontally, resulting in shimmering pixels.

[Picture Here: PS1 console optimized vs pstv optimized]

Sony Playstation 4

TurboGrafx-16/PCEngine

Microsoft Xbox

Preferred output: YPbPr.

Up to 720p available with custom firmware

Microsoft Xbox 360

Preferred Output: HDMI where available

Alternate Output: YPbPr for any Xbox 360 that doesn't support HDMI.

Microsoft Xbox One

Troubleshooting

Profile Repository

Generic Profiles

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Downscaling

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Console Specific

3DO Interactive Multiplayer

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Atari Jaguar

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Microsoft Xbox

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Microsoft Xbox 360

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Neo Geo AES

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Entertainment System (NES)

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Super Nintendo / Super Famicom

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo 64

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Gamecube

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Wii

Profile Name	Download 1	Profile Description
Generic	Download 2	Recommended for use with an unhacked Wii, optimized for 240p, 480i, and 480p.
VC 256		Recommended for use with the NES and Super NES Virtual Console games that output 256 wide pixels on a hacked Wii. Make sure to switch "Video Width" to Framebuffer in USBLoader GX.
VC ~256		Recommended for use with games that should be 256 pixels wide but are scaled to 320 pixels a hacked Wii. Make sure to switch "Video Width" to Framebuffer in USBLoader GX. DO NOT USE with games that actually output 256 pixels wide.
VC 320		Recommended for use with Virtual Console games that output 320 pixels wide on a hacked Wii. Make sure to switch "Video Width" to Framebuffer in USBLoader GX.

Nintendo Wii U

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Switch

Profile Name		Profile Description
N64 720	Download 1	Set the Switch to 720p to use this profile. NSO N64 games render at 720p. This profile is for use with scanlines to approximate the look on a CRT, not for additional sharpness. If you want a sharper picture, use the default profile.
NSO 256	Download 2	To be used with the NES, Super NES, and Sega Genesis Nintendo Switch Online emulators when the game has an 8:7 aspect ratio.
NSO 320	Download 3	To be used with the Sega Genesis Nintendo Switch Online emulator when the game has a 10:7 aspect ratio
GBA		This profile is for use with any GBA game on Switch, including the NSO GBA app as well as ports of GBA games that are scaled 6x to 1080p. This allows for a 13x scale to 2160p, where a default profile would only scale games 12x.
GBC		This profile is for use with any GBC game on Switch, including the NSO GBC app as well as ports of GBC games that are scaled 7x to 1080p. This allows for a 15x scale to 2160p, where a default profile would only scale games 14x.

Phillips CDi

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Pioneer LaserActive

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sega Master System

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sega Genesis / Megadrive

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sega Saturn

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sega Dreamcast

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation 1

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation 2

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation 3

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PSP

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation TV/Vita TV

The Playstation TV profiles require a hacked PSTV and the Sharpscale plugin to take advantage of the potential sharpness the PSTV can give. If your PSTV is not hacked, please use the default profile.

For the following profiles, please set the following options in Sharpscale:

PSTV Sharpscale Options
Option Name	Option Choice
Scaling Mode	Integer
PS1 Aspect Ratio	Pixel
Scaling Algorithm	Point
Unlock Frame Buffer Size	Off

Profile Name		Description
PSVita	Download 1	The PlayStation TV outputs a 544p window onto a 720p canvas. Upscaled 4x to fit 2160p. Cuts off 4 pixels vertically
PSP	Download 2	Sets Decimation Factor to 2 and Prescale to 1/2 The Playstation TV outputs a line-doubled 272p window into a 720p canvas. Upscaled 8x to 2160p. Cuts off 4 pixels vertically.
PS1 Generic		The Playstation TV will output the PS1 game to an integer scale of its signal that will fit inside 1280x720p. Use this profile for PS1 games that switch between many resolutions often. 480i will scale 1x. 512x224p and 640x224p will scale 2x. 384x224, 320x224, and 256x224 will scale 3x.

The following profiles require a slight change in Sharpscale settings. These profiles are best used with games that stick to one resolution for the majority of their gameplay. Do not use these with Chrono Cross or Silent Hill, their menus will cut off vertically

Sharpscale Settings
Option Name	Option Choice
Scaling Mode	Real
PS1 Aspect Ratio	Pixel
Scaling Algorithm	Point
Unlock Frame Buffer Size	Off

PSTV Profiles: PS1 Pixel Aspect Ratio
Profile Name		Profile Descriptions
PS1 256	Download 3	Use for PS1 games that are primarily 256x224.
PS1 320	Download 3	Use for PS1 games that are primarily 320x224.
PS1 384	Download 4	Use for PS1 games that are primarily 384x224.
PS1 512	Download 4	Use for PS1 games that are primarily 512x224
PS1 640	Download 5	Use for PS1 games that are primarily 640x224

TurboGrafx-16 / PC Engine

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Classic Mini Consoles

256	Download 1	Use with mini consoles that output a 3x integer scale of 8:7 aspect ratio games. Primarily used by NES and Super NES Classic Mini consoles. Note: The Famicom Classic Mini needs Digital Video Color space changed to "Limited"
320	Download 2	Use with mini consoles that output a 3x integer scale of 10:7 aspect ratio games. Primarily used by Sega Genesis Classic Mini.

Analogue Pocket

GBA	Download 1	Set Scale size to 6x in Pocket GBA settings. Outputs 13x scaled GBA games where the default profile would normally scale to 12x. Do not use with Pocket scanline effects.
GBC	Download 2	Set Scale Size to 7x in Pocket GBC settings. Outputs 15x scaled GBC games where the default profile would normally scale to 14x. Do not use with Pocket scanline effects.

Computer Specific

FM Towns

FM Towns computers once hitting white desktop variants output different video displays with some models performing internal upscaling conversions from 24khz to 31khz as well as some models performing 15khz to 31khz with adjustments in the TBIOS configuration file. EA and Pentium type desktops only output 31khz video modes. The below profiles are meant for all towers, UX, UG, UR, HG and HR models which are all models that do not perform internal conversion.
FM Towns will require a custom profile for any displays at 24khz

24Khz	Download 1	24Khz Display Mode

Sharp X68000

Sharp X68000 is unique with its outputs primarily being 15khz and 31khz. A few games have hidden selectable 24khz display modes.

Profile Name 1	Download 1	24Khz Mode in XXXX Game.
Profile Name 2	Download 2	24Khz mode

PC-8801

PC-8801 computers will output either 15khz or 24khz depending on the dipswitch settings in the back. If dipswitch settings are incorrect, games will refuse to boot and crash the computer. The 15khz VGA detection in the RT4K works very well for PC8801 and most video modes won't require a profile.
A 24khz signal will require a profile to display properly.

24Khz Mode in BASIC	Download 1	24Khz Mode in BASIC.

Advanced Features

Deinterlacer / Film Mode Setup

Motion Adaptive Settings

Motion Adaptive settings apply only to the Motion Adaptive Deinterlacing mode, allowing you to adjust it to your liking.

Sensitivity - Adjusts the sensitivity of Motion Adaptive, between Min, Medium, High and Max. The higher this is set, the more weaving will be present for moving parts of the screen, at the benefit of a stabler look for static parts of the screen. Many games will look just fine on the Min. setting, however several games may require Medium or higher. For example, Burnout 3: Takedown on PlayStation 2 has a subtle flickering and animated noise that throws off the Motion Adaptive Deinterlacer for still parts of the screen.

Notes

Deinterlacer -> -> Motion Adaptive Settings -> Sensitivity

(medium and high options might be might be reversed) Controls combing effect at costs of sharpness. Low = less combing.

Deinterlacer -> -> Motion Adaptive Settings -> Interpolator:

Basically controls how the "bob" portion of the MA is calculated. The bob is either taken from the line above, line below or the average of the upper and lower lines BFI. It's a matter of preference. I think either Top or Bottom interpolator looks a little sharper. Average is softer In the end it doesn't matter too much because Bob is only used during motion when it is hard to see detail anwyays

Deinterlacer -> Motion Adaptive Settings -> Detector:

This is a little complicated to explain... but let me try basically symmetric adds one frame of lag but the motion detection may be better. Because it is looking "one field into the future" idk if its really better tho in real life

HDMI -> BFI Control

-Strobe: How much the frame is divided down (i.e. 1 = divide by 2, 2 = divide by 3, 3 = divide by 4) from input to output -Blur: How many frames are ON vs OFF. So let's say we are converting 60 Hz -> 240 Hz. Blur = 1, ON, OFF, OFF, OFF. Blur = 2 is ON, ON, OFF, OFF -LCD Saver - inverts the pattern of the BFI to avoid renetion. But every few minutes u will see a flicker

Custom Mode Lines

#RT4K Custom Mode Line Format
#H active, H front porch, H sync, H total blank, polarity (1 = pos, 0 = neg)
#V active, V front porch, V sync, V total blank, polarity (1 = pos, 0 = neg)
#Nominal frame rate (floating point)
#Text name

Launch Information

https://www.retrotink.com/post/introducing-the-retrotink-4k

User Guides

Custom CRT Shadow Masks

The RT4K allows for the use of custom CRT shadow mask overlays.This is primarily intended to give an effect similar to CRT slot masks, as opposed to the pictures scanlines.

Custom CRT masks must be saved as 32-bit BMP files.
The maximum dimensions of a CRT mask is 16 x 16 pixels. They can be smaller, which will result in denser tiling of the mask across the screen.
A color value of 128 will be neutral,while 0 will completely black out the corresponding pixel. 255 will double the input value (although this will be clamped).
CRT masks will NOT adhere to the pixel grid like the RT4K's scanlines will. You can make this happen yourself by having your overlay match the dimensions of a single pixel, but this will vary depending on many factors, and so should be paired with a specific Profile.

Downscaling (pre-scale) Basics

Explain Downscaling here

RetroTINK-4K GUI Map

Basic Setup

Input Selection

More information concerning inputs can be found in the Inputs section.

Front
Composite	Selects the front composite input.
S-Video	Selects the front s-video input.

RCA
YPbPr	Selects the rear RCA YPbPr input.
RGsB	Selects the rear RCA RGsB input.
CVBS on Green	Selects the rear RCA CVBS input.

SCART
RGBS (75 ohm)	Selects the SCART input and sets it to RGBS
RGsB	Selects the SCART input and sets it to RGsB
YPbPr	Selects the SCART input and sets it to YPbPr
CVBS on Pin 20	information
CBVS on Green	information
Y/C on Pin 20/Red	information

HD-15
RGBHV	information
RGBS	information
RGsB	information
YPbPr	information
CBVS on Hsync	information
CBVS on Green	information
Y/C on Green/Red	information

Digital Video
thing a	information
thing b	information

Digital Video Output

More information concerning outputs can be found in the Outputs section.

Transmitter
HDR	Enables "HDR10 [8-bit]"
Colorimetry	Lets you choose between "Auto", "Rec. 709", "Rec. 2020", "Adobe RGB" and "Display-P3". With HDR enabled, Rec. 2100 is also available via the "Auto" setting.
Sync Lock	Lets you choose between "Triple Buffer", "Gen 50.0 Hz (x1)" and "Frame 50.0 Hz (x1)".
VRR	Lets you choose between "Off" and "FreeSync".
Deep Color	Lets you choose between "Off" and "On". Exceeds the HDMI 2.1 bandwidth spec if used with 4K60 output.

BFI Control
Strobe	information
Blur	information
LCD Saver	information

Output Resolution
4K60	Sets the output to 3840x2160p at 60 frames per second
4K50	Sets the output to 3840x2160p at 50 frames per second
1080p60	Sets the output to 1920x1080p at 60 frames per second
1080p50	Sets the output to 1920x1080p at 50 frames per second
1080p100	Sets the output to 1920x1080p at 100 frames per second
1440p100	Sets the output to 2560x1440p at 100 frames per second
1080p120	Sets the output to 1920x1080p at 120 frames per second
1440p120	Sets the output to 2560x1440p at 120 frames per second
480p60	Sets the output to 640x480p at 60 frames per second

Profiles

Load Profile
Load From File	Loads a chosen profile from the "profile" folder on the SD card.
Load Default	Loads the Default Profile.

Save Profile
Save Current	Saves the current profile by overwriting the original file on the SD card.
Save As New	Saves the current profile as "New Profile #".

Assign Profile
Button 1	Sets a specified profile on the SD card to Button 1 on the remote.
Button 2	Sets a specified profile on the SD card to Button 2 on the remote.
Button 3	Sets a specified profile on the SD card to Button 3 on the remote.
Button 4	Sets a specified profile on the SD card to Button 4 on the remote.
Button 5	Sets a specified profile on the SD card to Button 5 on the remote.
Button 6	Sets a specified profile on the SD card to Button 6 on the remote.
Button 7	Sets a specified profile on the SD card to Button 7 on the remote.
Button 8	Sets a specified profile on the SD card to Button 8 on the remote.
Button 9	Sets a specified profile on the SD card to Button 9 on the remote.
Button 10	Sets a specified profile on the SD card to Button 10 on the remote.
Button 11	Sets a specified profile on the SD card to Button 11 on the remote.
Button 12	Sets a specified profile on the SD card to Button 12 on the remote.
Power Up	Sets a specified profile on the SD card to load when the RT4K is powered up.

Advanced Settings

Scaling/Cropping

Input Crop
Left Trim	Adjusts trim on the left edge of the picture.
Right Trim	Adjusts trim on the right sedge of the picture.
Top Trim	Adjusts trim on the top edge of the picture.
Bottom Trim	Adjusts trim on the bottom edge of the picture.
Vert. Pre-Scale	information
RoTATE (Beta)	information

CP Auto Crop
Vertical Only	Crops only the top and bottom edges of the image, sets Aspect Correction to "4:3 (PAR)" and Scaling Mode to "Proportional".
Full Crop to 4:3	Crops all edges of the image, sets Aspect Correction to "4:3 (PAR)" and Scaling Mode to "Proportional".
Full Crop to 16:9	Crops all edges of the image, sets Aspect Correction to "16:9 (PAR)" and Scaling Mode to "Proportional".

Scaler
Aspect Correction	Lets you choose between "4:3 (PAR)", "16:9 (PAR)" and "1:1 (Sq. Pixel)" options.
Scaling Mode	Lets you choose between "Auto Fill", "Proportional", "Free-Form" and "Auto Fill Integer" options.
Vert. Factor	Adjusts the vertical height of the image. Only available when Scaling Mode is set to "Proportional" or "Free-Form".
Hori. Factor	Adjusts the Horizontal width of the image. Only available when Scaling Mode is set to "Free-Form".

Buffer
Length	Displays the current lag in milliseconds. Can be set to "Min. Lag", "1/2 Frame" or "1 Frame".

Masking Color
Red	Adds red to the cropping mask, between 0 and 31.
Green	Adds green to the cropping mask, between 0 and 31.
Blue	Adds blue to the cropping mask, between 0 and 31.
Show	Lets you choose between "Cropping Only" and "Always".

Processing / Effects

Interpolation
Vert. Kernel	Lets you choose between "Bilinear Sharp", "Bilinear Med.", "Bilinear Std.", "Bilinear Soft", "Cubic", "Lanczos2", "Lanczos3", "Sinc", and "None".
Hori. Kernel	Lets you choose between "Bilinear Sharp", "Bilinear Med.", "Bilinear Std.", "Bilinear Soft", "Cubic", "Lanczos2", "Lanczos3", "Sinc", and "None".
Anti-Ringing	Can be set to "On" or "Off". Only visible on "Lanczos2" and "Lanczos 3".

Scanline
Function	Lets you choose between "Off", "Exponential", "Gaussian", "Super Gaussian", "Linear", "Box", "LCD Mono" and "LCD RGB". Anything except for "Off" will enable the settings below.
Strength	Increases scanline strength from 0 to 99.
Modulation	Increases modulation strength from 0 to 99.
Red Bleed	Enables red bleed.
Red Convergence	Adjusts red convergence from -10 to 10.
Blue Convergence	Adjusts blue convergence from -10 to 10.

Mask
Enable	Enables the Mask feature, as well as the Strength option. Will not appear to do anything until "Load from File" is used.
Strength	Adjusts the mask strength from -10 to 10.
Load from File	Select a Mask File from the "mask" folder on the SD card.

Horizontal Blur
Function	Lets you choose between "Off" and "IIR LPF", enabling the Cut-Off Freq option below.
Cut-Off Freq	Adjusts the blur strength from 0.50 MHz to 9.00 MHz, in 0.25 increments.

Color Correction

Gamma/Linear Light/HDR
Input Factor	Can be adjusted between 0.99 and 5.00.
Input Lift	Can be adjusted between -1.00 and 1.00.
Input Gain	Can be adjusted between 0.00 and 10.00.
Output Factor	Can be adjusted between 0.10 and 5.00.
SMPTE 2048 PQ	information

Color Space Conversion
Custom Matrix	Enables the Input RGB to XYZ options below.
Load from SD	Lets you load a CSC file from the "csc" folder on the SD card.

Input RGB to XYZ
Xo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Xo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Xo[Bin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Bin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Bin]	Can be adjusted between -1.75000 to +1.75000.

Misc.
Bit Crush	Lowers the color depth of the picture. Can be adjusted between "Off" and "7 bits Removed".

Black Frame Insertion

BFI Insertion
Strobe	information
Blur	information
LCD Saver	information

BFI Color
Blending Mode	Lets you choose between "Solid" and "Alpha".
Red	Adjusts Red, Green and Blue from 0 to 31.
Green	Adjusts Red, Green and Blue from 0 to 31.
Blue	Adjusts Red, Green and Blue from 0 to 31.

Deinterlacer / Film

Mode
Algorithm:	Lets you choose between "Motion Adaptive", "Weave", "Bob", "Linear", "Blend", "CRT Simulation" and "LCD Blending".
Field Inversion:	Reverses the fields of 480i signals. Can be set to "Off" or "On".

Motion Adaptive Settings
Sensitivity	Adjusts the sensitivity of the Motion Adaptive Deinterlacer. Can be set to "Low", "Medium", "High" and "Max". Higher settings result in a more solid image but with more weaving artifacts.
Noise Threshold	Adjusts the noise threshold, at the cost of weaving. Can be adjusted between 0 and 63.
Interpolator	Choose which field to prioritize. Can be set to "Average", "Bottom Field" and "Upper Field"
Detector	Can be set to "Zero-lag" or "Symmetric".

Bob Settings
Offset	Adjusts how far each field is shifted when using the "Bob" Algorithm. Can be set between -3 and +3.

Film Mode
Inverse Telecine	Enables a detector for "3:2" telecine (24fps content) and "2:2" telecline (30fps content).
Dejudder 24 Hz	Can be set to "Off" or "On".

Cadence Detection
Motion Digital	Can be set from 0 to 500.
Motion CP	Can be set from 0 to 500.
Motion SDP	Can be set from 0 to 500.
Threshold	Can be set from 0 to 500.

Acquisition

Digital In Receiver

Input Decimation
Input Pixels	information
Output Pixels	information
Initial Phase	information

Colorspace
4:2:2 Upsampler	information
Input Range	information
Input RGB range	information

RGB / Component ADC

Sampling
Samples per Line	Manually set the sampling.
Decimation Factor	Can be set to between 2 and 16.
Decimation Phase	Value range matches the Decimation Factor.
Sub-Phase	Adjusts the Sub-Phase in 11.25 increments. Can be set as high as "348.75 deg"
Anti-Alias LPF	Can be set to "Auto (16MHz)", "9MHz (Strong)", "16 MHz (Med)", "35 MHz (Light)", "95 MHz (Min.)" and "Off".

Sync
SoG Threshold	Adjusts the Sync on Green Threshold in 11.29 increments. Can be set between "0.00 mV" and "327.42 mV".
Pre-coast	Can be set between 1 and 31.
Post-coast	Can be set between 1 and 31.
Slow-lock	Gives more time to lock onto Sync on Green. Can be set to "Off" or "On".

Gain
Pre-ADC	Adjusts the picture gain. Can be set between -0.7 and +0.8.
Red	Adds red to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.
Green	Adds green to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.
Blue	Adds blue to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.

Offset
Red	Can be set between -100 and +100.
Green	Can be set between -100 and +100.
Blue	Can be set between -100 and +100.

Auto Calibrate
Phase	Analyzes the picture to determine the Sub-Phase setting. Works best on detailed images with high contrast details.
Gain	Analyzes the picture to determine the Red, Green and Blue Phase settings. Works best on calibration screens like in the 240p Test Suite.

Sample Rate Detection

Control
Auto Dec. Factor	Can be set to "Off" or "On". Enables all other options in the Sample Rate Detection Menu
Auto Dec. Phase	Can be set to "Off" or "Auto".
ADC Sample Rate	Manually set the sampling.

Progressive Detection
Enable Sample Rate A	information
Enable Sample Rate B	information
Enable Sample Rate C	information
Enable Sample Rate D	information
Enable Sample Rate E	information
Enable Sample Rate F	information

Interlaced Detection
Enable Sample Rate A	information
Enable Sample Rate B	information
Enable Sample Rate C	information
Enable Sample Rate D	information
Enable Sample Rate E	information
Enable Sample Rate F	information

SDP Decoder

Gain / Balance
Brightness	information
Contrast	information
Chroma	information
Phase	information
Blue Only	information
Setup	information

Processing
Y/C Filter	information
Comb Bandwidth	information
Chroma Badwidth	information
Sharpness	information
CTIE	information

Sync
H-Lock Speed	information
Standard	information

Audio Input

Sampling
Sample Rate	Can be set to "48 kHz" or '96 kHz".
Pre-amp Gain	Can be set between "-24.0 dB" and "+28.0 dB" in 0.5 increments.

Source
Input Override	Manually changed the audio input to another source. Can be set to "Off", "RCA", "HD-15", "SCART", "Front" or "S/PDIF".
Input Swap	Can be set to "Mono (Left)", "Mono (Right" or "L/R Swap".

System

OSD / Firmware

On Screen Display
Position	Can be set to "Left", "Center" and "Right".
Auto-Off	Sets the time the menu will disable after inactivity. Can be set up to "100 sec" in 10 sec increments.
Load Banner	Loads a menu banner from the "image" folder on the SD card.
Enable Debug OSD	Permenantly displays one of the debug OSDs on the screen. Can be set to "Off", "Status Pg 1", "Status Pg 2", "Status Pg 3" or "Console".

Firmware Update
Check SD Card	Checks the SD card for update files stored in the SD card's root directory.

Status

Status
Lets one display one of three System Status pages relating to the RT4K.

Device

Status

System Status Page 1:

Video Source
Video Source	CP Proc. (I assume CP Proc will change based on selection)
Input Timing	information
Pixel Clock	information
Freq	information
Detected Mode	information

Audio Input
Audio Input	I2S (I assume will change based on audio input)
Measured Freq	information
Measured Freq	information
HDMI N / CTS	information

FPGA Core
Scaler Clock	information
PLL VCO	information
Pipeline	information
SDRAM Clock	information
SDRAM Load	information

HDMI Transmitter
Output Timing	information
Active Size	information
Pixel Clock	information
HDMI Standard	information

PIC32MX MCU
System Clock	information
Uptime	information
Loop Time	information
Last IR Code	information
SD Card Free	information

System Status Page 2:

HDMI Input Protocol Analyzer
TMDS	information
Mode	information
Resolution	information
Colorspace	information
H. Timing	information
V. Timing (F0)	information
V. Timing (F1)	information
Audio	information
AVI Infoframe	information
Aud. Infoframe	information
VS Infoframe	information
ACP Infoframe	information

System Status Page 3:

HDMI TX Information
TX Mode	information
Hot Plug	information
Scrambling	information
Clock Factor	information
Ch 0 Error	information
Ch 1 Error	information
Ch 2 Error	information
Sink EDID Dump	information

Diagnostic Console

to do

Diagnostic Console
Displays a diagnostic console screen regarding Digital In TX channels.

About

About
Displays the name of the device, the firmware version, and the Device ID.

@@ Line 735: / Line 735: @@
 ====Community Profiles====
 ====Profile Troubleshooting====
-====Advanced Settings====
+=== Advanced Settings ===
 ====Automatic Settings====