AV:RetroTINK-4K

The RetroTINK-4K, alongside the included remote and SD card.

This page is a work in progress. It's possible that not all features or settings are covered at this moment, and additions will be made as new features are introduced.

The RetroTINK-4K (commonly abbreviated as "TINK-4K" or "RT4K") is an advanced video scaler from RetroTINK LLC. Building on the functionality of the RetroTINK-2X and RetroTINK-5X, the RetroTINK-4K offers high-end video scaling and processing at resolutions up to 4K60.

Overview

The RetroTINK-4K is the latest evolution of the RetroTINK line of video line doublers and upscalers. Below is a list of some standout features:

Output

• HDMI® up to 4K60
  • Flexible output modes including 480p, 1080p, 1440p at various refresh rates
  • Custom modelines on the SD card
• Fully buffered video (drop-free on input changes), Gen Locked and Frame Locked sync modes
• HDR10 output with full color correction to Rec. 2020
• High frame rate output modes: 1440p120, 1080p240
• Optional deep color output (10 bits at 4K60 may not be compatible with all displays)
• Up to 8-ch LPCM audio

Inputs

• Supports for virtually all analog formats:
  • HD15/VGA: RGBHV, RGBS, RGsB, YPbPr, S-video and Composite
  • SCART: RGBS, RGsB, YPbPr, S-video and Composite
  • Rear RCA: RGsB, YPbPr and Composite
  • Front Composite
  • Front S-Video
• HDMI® Input supporting up to 1080p60/1200p (CVT-rb)
• Analog audio input sampled at up to 96kHz/24-bit with full gain control
• Optical TOSLINK audio input supporting 2-Ch LPCM or compressed surround
• HDMI® audio supports up to 8-ch LPCM

Analog Video

• Automatic gain calibration
• Automatic phase calibration
• Automatic input cropping to trim borders
• Full control of gain, offset and sample rate
• Console specific automatic sample rate detection (experimental feature)
• Support for a wide variety of off-spec arcade and PC boards (may require custom profiles to properly trim and center the image)
• Max input resolution of 1920x1080p60 or 1920x1200p60 CVT-rb
• Robust composite/S-video decoder with multi-region support (NTSC, PAL, PAL-60, SECAM)

Scaling

• Fully flexible, custom cropping and zooming in the horizontal and vertical space independent of other settings
• Automatic aspect ratio correction to 4:3 or 16:9
• Motion adaptive deinterlacing including film modes for 3:2 and 2:2 inverse telecine (experimental feature)
• RoTATE 90 deg CW or CCW (for 240p, 288p and 360p inputs)

CRT Simulation

• Multiple CRT beam profiles
• Fully configurable CRT beam strength and intensity modulation
• Adjustable CRT masks and strength
• Interlaced video simulation with offset scanlines
• LCD simulation patterns that automatically adapt to scaling, including non-integer factors

Image Processing

• End to end RGB pipeline with internal 12-bit precision
• Conventional gamma and approximated modes to minimize quantization error
• Advanced and fully configurable gamma and perceptual quantizer (HDR)
• Advanced color gamut transforms to simulate different display technologies
• Black frame insertion engine with customizable pattern and intensity
• Linear light processing

User Interface

• Advanced OSD menu-based system
• SD Card for storing custom modelines, firmware updates and saving profiles
• Support for over 100,000 profiles
• Custom premium remote control

Product Contents

A new RetroTINK-4K package will come with the following items:

• 1x RetroTINK-4K unit
• 1x 8GB SD Card, pre-loaded with software and profiles.
• 1x USB-A / USB-C SD Card Reader
• 1x Remote Control
• 1x USB-A to USB-C Power Cord

The contents do not include an AC adaptor. We recommend using a 5V 2A USB-A adaptor, similar to ones like Apple iPad or Samsung phone chargers. We do not recommend plugging the RT4K into the USB ports of your TV, as they often do not provide enough power and may result in operation errors.

Getting Started

Insert SD card with RT4K firmware, HDMI® output, USB-C power and whatever inputs you wish to use.

The RetroTINK-4K is designed to be powerful, yet easy to use and quick to set up. Here are some steps to get started using the RetroTINK-4K:

1. SD Card - A card is included with every RetroTINK-4K that includes the launch firmware and profiles. Please make sure this card is inserted in the device, as it is required for proper operation. If you lose the card, any FAT32 SD card 32 GB or less may be substituted.
2. USB-C Power - Connect a USB-C cable supplying at least 5V/2A to the USB-C power input on the 4K.
3. Video Output - Connect an HDMI® cable (2.0 or higher / 18Gbps+) from the RetroTINK-4K output to your display.
4. Video Input - Connect your device's signal to any of the RetroTINK-4K's inputs. More information on supported connections can be found in the Inputs section.
5. Confirm Video Output - By default, the RetroTINK-4K outputs 4K60. If you don't see any picture, confirm that your display supports 4K60, or press the button on the remote that matches the resolution of your display (1080p, 1440p, or 480p). See the Remote and Output sections for more information.
6. Select Your Input Source - Press the "Input" button at the top of the remote, then choose the port and signal your game system is using.
7. Enjoy - Once your video source is visible, you're ready to go! Enjoy the high quality, low latency scaling of the RetroTINK-4K. Time to play the game!

Basic Analog Calibration

With your game up and running, you may want to consider two more steps if you're using an analog video source (note that HDMI® video sources do not require calibration):

Auto Calibrate the Gain - The RetroTINK-4K has a function to automatically calibrate the gain, which works well so long as there's a patch of pure white somewhere on the screen. Gain should be applied on a per-console basis. To quickly use Auto Gain, press the "Gain" button on the remote. Advanced users may want to use the manual gain controls under Advanced Settings > RGB/Component ADC, in tandem with the 240p Test Suite.

Crop the Picture - Cropping the picture is how the RetroTINK-4K scales images to the edges of a screen and centers them. For best results, use a screen that has no black or dark edges. Crops should be applied on a per-game basis. There are three ways to automatically crop the picture, which can be accessed via the AUX buttons at the bottom of the remote: AUX1 - "Vertical Only", cropping only the top and bottom edges. AUX2 - "Full Crop to 4:3", cropping all four edges. AUX3 - "Full Crop to 16:9", cropping all four edges and setting the Aspect Correction to 16:9. You can also manually crop and resize the picture if you wish by going to Advanced Controls > Scaling/Cropping. Head to that section to learn more.

Tweaks, Filters and Beyond

Of course, there is a lot more you can do with the RetroTINK-4K. Here are some more advanced options to explore:

• Update the Firmware
• Choose an Expert-Crafted Optimal Profile
• CRT and Scanline Effects
• Improve Image Vividness with HDR
• Improve Motion Clarity With Black Frame Insertion

Firmware Updates

The RetroTINK-4K can be updated to any firmware, with new firmware releases adding more new features as they are made.

1. Power off your RetroTINK-4K and remove the SD card.
2. Insert the SD card used for your RT4K into the SD card slot on your computer. If your computer doesn't have an SD card slot, you can connect it using the provided USB adaptor.
3. Download the latest firmware .zip file from the RetroTINK website.
4. Extract the contents of the .zip file to the SD card's root directory.
5. Remove the SD card and insert it into the SD card slot on the RetroTINK-4K.
6. There are two methods for initiating the installation of a new firmware. If you have multiple firmware files on the SD card, the RT4K will always pick the most recent one.
   • Option 1: Power on the RetroTINK-4K, then go to Advanced Settings > OSD/Firmware. In the Firmware update section, select "Check SD Card" to scan for the firmware file, then confirm that you want to install it.
   • Option 2: Hold down the blue Reset button on the back of the RetroTINK-4K, then power it on. The firmware installation will begin automatically.
   • If the LED blinks red, an install error has occurred. Check the files on the SD card and try again.
7. The RT4K will reboot for about 40 seconds, with the front LED flashing pink and then blue. Once done, it will power on again as normal with a green LED. You're done!

All custom profiles, CSC files, banner images, input modes, mask overlays and modelines will be kept, as those are stored on the SD card instead of on the RT4K itself.

Remote

RetroTINK-4K Remote Diagram
	Button	Description	Button	Description	Button	Description
	Power	Powers on / off the RT4K	11	Profile 11	4K	Switches to 3840x2160p 60Hz
	INPUT	Input source selection menu	12	Profile 12	1080p	Switches to 1920x1080p 60Hz
	OUT	HDMI® Output menu	MENU	RetroTINK-4K Main Menu	1440p	Switches to 2560x1440p 60Hz
	SCL	Scaling/Cropping menu	BACK	Back out to previous menu	480p	Switches to 720x480p 60Hz
	SFX	Processing/Effects menu	△	Up	RES1	Custom Output Resolution 1
	ADC	HDMI® Receiver menu if HDMI® In is currently displayed RGB/Component ADC menu if an RGB or Component input is currently displayed SDP Decoder menu if a Composite / S-Video input is currently displayed	◁	Left	RES2	Custom Output Resolution 2
	PROF	Profiles menu	ENTER	Enter	RES3	Custom Output Resolution 3
	1	Profile 1	▷	Right	RES4	Custom Output Resolution 4
	2	Profile 2	▽	Down	AUX1	"Vertical Only" Auto Crop
	3	Profile 3	DIAG	Diagnostic Console screen	AUX2	"Full Crop to 4:3" Auto Crop
	4	Profile 4	STAT	Status screen	AUX3	"Full Crop to 16:9" Auto Crop
	5	Profile 5	AUTO-GAIN	Auto Calibrate Gain	AUX4
	6	Profile 6	AUTO-PHASE	Auto Calibrate Phase	AUX5
	7	Profile 7	PLAY/PAUSE	Pause current screen	AUX6
	8	Profile 8	SAFE	Safe Mode	AUX7
	9	Profile 9	SYNC-GEN	Sync Lock - Gen Lock	AUX8
	10	Profile 10	SYNC-BUF	Sync Lock - Triple Buffer	-

Pause Button

The Remote features one function that cannot be accessed anywhere else: the Pause function. Pressing this will pause the on the current frame and mute the audio. This frame will even be remembered if you switch to a different input source and back.

• Perhaps the most useful application of the Pause Button is the Deinterlacer/Film menu. Here you'll be able to adjust the deinterlacing settings and see their effects more easily in a scene in motion, letting you tweak them to your liking more easily.

There are a few situations where using the Pause function will have undesirable results, such as loading a different profile, using the cropping tools, or engaging 3:2 Inverse Telecine. Other functions, such as Black Frame Insertion, won't be visible at all because they require new video frames in order to work. In these cases, simply unpause to resume normal operation.

Safe Mode

Safe Mode is an option accessible by pressing the blue Reset button on the back of the unit, or by holding down the "SAFE" button on the remote for two seconds. This causes the following:

• Loads the Default profile.
• Sets the input to HDMI® In.
• Sets the output to 480p at 59.94 Hz.

Safe Mode is intended for use in troubleshooting, as any display that supports HDMI® should be required to support 480p60. It's also handy as a fall-back in case you need to return the RetroTINK-4K to a default state for any reason.

LED Light

The RetroTINK-4K has a front LED light that changes color and behavior to convey information about its operation to the user. Below is a chart for LED light behavior and what they mean.

Color	Description
No light	The RT4K has no power. No electrons, no business.
Slow Red pulse	The RT4K is sleeping, and must be turned on for use.
White	The RT4K is booting up, but is not yet ready for use.
Green	The RT4K is on and ready for operation.
Yellow flash	System files not found on SD card during boot. Check to see if the SD card is correctly inserted, that it has the .rbf system file, and that the rt4k.bin file matches it.
Purple-Purple flash	The RT4K is updating the firmware.
Blue-Blue flash	Firmware update is successful.
Red flash	Firmware update error. Check the files on the SD card and try again (the unit is NOT bricked).

Inputs

The RetroTINK-4K features inputs for a wide variety of signals and connector types, which can be selected in the Input Selection menu. These options can be accessed by pressing the Input button at the top of the remote, or by pressing the Menu button and choosing "Input Selection".

HDMI®

HDMI® Input

The RetroTINK-4K supports many resolutions digitally, up to 1920x1080p60 or 1920x1200p60 CVT-rb. Unlike standard consumer equipment, the RetroTINK-4K can tolerate and adapt to arbitrary and off-spec resolutions. It does NOT support higher resolution inputs, including 1440p and 4K input. If these inputs are fed into the RT4K, it will not display anything.

Front

The RetroTINK-4K offers S-Video (over Mini-DIN) and Composite (over RCA) inputs in the front (which can be concealed / revealed by moving the sliding panel). The red and white RCA jacks are stereo audio inputs. Red/White front audio inputs are active when either the Front Composite or S-Video input is selected (assuming audio input override is not used).

Front Inputs
	Composite	To use Composite video, use the yellow RCA jack for video (CVBS/Composite) and the Red/White RCA jacks for right and left audio input, respectively.
	S-Video	To use S-Video, use the Mini-Din for video (Y/C S-Video) and the Red/White RCA jacks for right and left audio input, respectively.

Rear RCA

The rear RCA jacks support YPbPr (Component), RGsB, and CVBS (aka Composite) inputs.

Rear RCA Input
	YPbPr	The Rear RCA input supports YPbPr (Component video). The maximum resolution supported is 1920x1080p at 60fps, or 148.5Mhz. To use YPbPr, connect the Red, Green and Blue YPbPr video cables to their corresponding colored RCA connectors, noting that the Red/White pair to the left is for stereo audio input.
	RGsB	The Rear RCA input also supports RGsB (aka RGB Sync on Green), a flavor of RGB that sends the sync alongside the Green signal. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz To use RGsB, connect the Red, Green and Blue RGsB signals to their corresponding colored RCA connectors, noting that the Red/White pair to the left is for stereo audio input.
	CVBS on Green	Composite video (CVBS) can be used with the Rear RCA inputs. The maximum supported resolution is 480i. To use CVBS on Green, connect the yellow Composite signal connector to the Green RCA jack, then setting the input to "CVBS on Green" option in the Input Selection menu. The Red / White pair of jacks furthest left is for stereo audio input.

SCART

The SCART port is the large rectangular input on the right-hand side of the device. SCART has many different options for video input using the same connector design, as it was designed to carry a wide array of them using a single cable.

• Two M4x0.7 thread screw-holes sit on either side of the SCART port, 70.4mm apart from each other relative to their centers. These allow for a user-made solution to give a more secure fit for the SCART cable (similar to the HD-15 port's screw-holes).

SCART Input
	RGBS (75 ohm)	RGBS is a form of RGB where sync is sent through a discrete line. The RetroTINK-4K accepts the following RGBS signal formats via SCART: Composite Sync (attenuated), Sync-on-Luma, and Sync-on-composite. They all work by sending information down the Red, Green, Blue, and "Sync" lines. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	RGsB	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via SCART. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	YPbPr	YPbPr is sent through the Green, Blue, and Red pins, respectively. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	CVBS on Pin 20	Composite video sent through Pin 20, usually through a composite to SCART adapter or if your cable uses sync-on-composite video and you wish to use composite instead of RGB. As with all composite signals, only 240p/480i/288p/576p signals are supported.
	CBVS on Green	Composite video can be sent through the Green pin. This would be useful if you use a component (YPbPr) to SCART adapter, just plug composite (yellow) into the Y RCA jack (Green). As with all composite signals, only 240p/480i/288p/576p signals are supported.
	Y/C on Pin 20/Red	S-Video (Y/C) can be sent down Pin 20 (sync) and the Red pins. You will need a S-Video to SCART adapter. As with all S-video signals, only 240p/480i/288p/576p signals are supported.

SCART Jack Pinout
	Pin #	RGBS (75 Ohm)	RGsB	YPbPr	CVBS on Pin 20	CBVS on Green	Y/C on Pin 20/Red
	1	Unused
	2	Audio In - Right
	3	Unused
	4	Ground
	5	Ground
	6	Audio In - Left
	7	Blue	Blue	Pb
	8	Unused
	9	Ground
	10	Unused
	11	Green	Green+Sync	Y		CVBS
	12	Unused
	13	Ground
	14	Unused
	15	Red	Red	Pr			Chroma (C)
	16	Unused
	17	Ground
	18	Ground
	19	Unused
	20	Sync			CVBS		Luma (Y)

HD-15

The HD-15 connector (or VGA connector) is commonly associated with PCs, however it's also famously available for the SEGA Dreamcast.

• Unlike SCART, the HD-15 port does not accept audio. When using HD-15, audio should be input using the RT4K's 3.5mm TRS input (associated with the HD-15 port by default) or the TOSLINK "optical" input.

HD-15 Input
	RGBHV	RGBHV is a form of RGB where information is sent through 5 lines: Red, Green, Blue, Horizontal Sync, and Vertical Sync. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz. This is most common for PC sources.
	RGBS	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via SCART. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	RGsB	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via SCART. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	YPbPr	YPbPr is sent through the Green, Blue, and Red pins, respectively. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	CBVS on Hsync	Composite video sent through the horizontal sync line. As with all composite signals, only 240p/480i/288p/576p signals are supported.
	CBVS on Green	Composite video can be sent through the Green line. As with all composite signals, only 240p/480i/288p/576p signals are supported.
	Y/C on Green/Red	S-Video (Y/C) can be send down Green (Y) and the Red (C) pins. As with all S-video signals, only 240p/480i/288p/576p signals are supported.

HD-15 Jack Pinout
	Pin #	RGBHV	RGBS	RGsB	YPbPr	CBVS on Hsync	CBVS on Green	Y/C on Green/Red	Data
	1	Red	Red	Red	Pr			Chroma(C)
	2	Green	Green	Green+Sync	Y		CVBS	Luma(Y)
	3	Blue	Blue	Blue	Pb
	4	Unused
	5	Ground
	6	Ground
	7	Ground
	8	Ground
	9	Unused
	10	Ground
	11	Unused
	12								External Transmit (EXT TX)
	13	Horizontal Sync	Sync			CVBS
	14	Vertical Sync
	15								External Receive (EXT RX)

3.5mm TRS Audio

3.5mm TRS Audio

The RetroTINK-4K allows for audio through a 3.5mm TRS input. This accepts stereo analog audio. By default, this is associated with the HD-15 port, as that port does not accept audio signals.

Optical Audio

Optical Audio

The RetroTINK-4K offers a discrete optical audio TOSLINK input. This input can accept 2-channel LPCM and compressed surround sound.

Alternate Audio Inputs

The RetroTINK-4K allows you to reassign audio inputs from their default video source. Go to Advanced Settings, and select "Audio Input" under the "Acquisition" section. The "Input Override" option under "Source" allows the audio for the current input video input to be taken from a different audio source. The only exception is that it is not possible to assign HDMI® audio to a non-HDMI® video source. The reverse, however, is possible.

• This menu also has the Input Swap option, letting you swap the audio input channels (handy for some third-party Saturn cables), or derive mono audio using the left or right channels (useful for single-channel systems like the NES).

Audio Input Override Sources

Picture	Name	Description
	RCA (Rear)	The leftmost two RCA inputs in the rear. White and Red,
	HD-15	The 3.5mm TRS input in the rear.
	SCART	The SCART input on the side. Audio is fed in through pins 2 and 6.
	Front	The red and white RCA inputs in the front of the unit.
	S/PDIF	Optical audio fed through a TOSLINK input.

HDMI® Output

The RetroTINK-4K only outputs via the HDMI® Out port. Note that the RetroTINK-4K can not output video or audio through any other port.

The HDMI® Output menu allows you to set your output resolution, enable black frame insertion, change your colorspace output (colorimetry), and more. Here is a breakdown of some key functions:

Output Resolutions

The following outputs are readily supported by the RetroTINK-4K, and are provided as the first eleven Output Resolution options at the bottom of the HDMI® Output menu. Which resolutions available by pushing their respective button on the remote are also noted. If you are unsure which resolution to use, use the buttons on the remote to quickly try them.

RetroTINK-4K Output Resolutions

Resolution	Description	Remote Button?
4K60	Default resolution and framerate for 4k displays, aka 3840x2160p. Default Resolution for the RT4K	Yes
4K50	Intended for PAL games and 24Hz content.	No
1080p60	Default resolution for 1080p displays.	Yes
1080p50	Intended for PAL games. and 24Hz content	No
1440p60	Default resolution and framerate for 1440p monitors, aka 2560x1440p.	Yes
1440p50	Intended for PAL games and 24Hz content	No
1080p100	Intended for PAL games and 24Hz content with BFI	No
1440p100	Intended for PAL games and 24Hz content with BFI	No
1080p120	Intended for NTSC content with BFI	No
1440p120	Intended for NTSC content with BFI	No
480p60	Minimum suggested output resolution for modern displays, aka 720x480p. Pressing the Reset button on the back of the unit activates this resolution.	Yes

HDR

HDR is a way for the RetroTINK-4K to output a much more luminous picture for TVs that support it. HDR is intended for use with either Black Frame Insertion or Scanlines and Masks, as it helps compensate for the darkened image.

• Currently, the only option available is "HDR10 [8-bit]".
• You can adjust the brightness of HDR by going to Advanced Settings > Color Correction, then adjusting the "SMPTE 2084 PQ" value. This is useful is you want to play in HDR without scanlines, so that light tones are perceptible instead of being overly bright.

The table below shows two photos of an LG-CX displaying the RT4K using the "PVM 600 TVL" profile, under the HDR CRT Simulation folder. It's impossible to communicate the luminance of HDR in SDR, so here the camera had its exposure set for the HDR photo first, demonstrating the luminance gain compared to the SDR photo.

HDR Comparisons - Off-screen Photos
PVM 600 TVL scanlines - SDR.	PVM 600 TVL scanlines - HDR.

Colorimetry

HDMI® Output Colorimetry specifies the colorspace of the HDMI® output. By default, the Auto setting will select Rec. 709, and toggle to Rec. 2100 when HDR is enabled. You may wish to manually set output to Rec. 2020 (without HDR enabled), Adobe RGB or DCI-P3 if your display supports a wider color gamut. This may improve the image quality/accuracy when using the settings in the Color Correction menu.

Sync Lock

Sync Lock controls how the RetroTINK-4K synchronizes the output frame rate with the input frame rate, and handles these input changes.

Older video game consoles didn't always have perfect video timings, and while CRTs typically had no problems working with them, these "imprecise" consoles can sometimes have trouble working with modern TVs and capture devices that conform to a more rigid standard. Some games, such as Silent Hill or Chrono Cross on the PlayStation 1, will alternate between 240p or 480i video modes if you are in-game or in the items / pause menu, respectively. On many displays, upscalers and capture devices, this will create a long delay and a "no input detected" screen for several seconds while the device reorients to the new video mode. The issue of a device taking a gameplay-harming amount of time to change between video modes has been colloquially called the "Chrono Cross" problem. How the RT4K handles all of this can be chosen in the Sync Lock section.

• Triple Buffer - Operates the output independently from the input, which results in a stable output signal even if the input signal glitches or changes. However, this comes at the cost of a variable lag, usually between a fraction of a frame to a fraction of a frame plus one whole frame. On occasion, you will see judder when frames need to be dropped or repeated in order to maintain sync.
• Gen Lock - This is the recommended mode as long as your display is compatible with the source's refresh rate. Gen Lock loosely couples the output frame rate with the input frame rate. After a few seconds, the output frame rate will lock with the input frame rate and achieve minimum lag without screen judder. If Gen Lock is giving your equipment trouble, try enabling VRR if they support it.
• Frame Lock - Tightly couples the input and output frame rates. Any change in the input frame rate will cause a disruption in the output signal and a hard re-synchronization.

VRR (Variable Refresh Rate)

The RetroTINK-4K can flag its output as VRR. While the RetroTINK-4K itself never outputs variable frame rates, settings this flag may be useful to force the display to accept a broader range of refresh rates, including if you're using Gen Lock. It is also useful on some displays to prevent re-buffering and other frame rate changes, which will interfere with the RetroTINK-4K's BFI generator. Lastly, some TVs activate a low-lag mode if they detect the VRR flag, which will improve the gameplay experience.

Deep Color

This option changes the bit color depth of the RT4K from 8 bits (Off) to 10-bits (On), increasing the number of colors in the picture. This can be useful if you've used any setting that adjusts the color of the picture.

• Engaging Deep Color may cause issues with some equipment like TVs or capture cards, since enabling it while using 4K60 output will exceed the HDMI 2.0 bandwidth spec. In this case, your options are to either disable Deep Color, or use a lower output resolution. PAL systems may have better luck if the 4K50 option is chosen instead, so long as HDR is disabled.

BFI Control

Gives you quick access to the Strobe and Blur functions of Black Frame Insertion. For explanations on what these do, as well as more BFI controls, head to the Black Frame Insertion (BFI) section.

Profiles

The Profiles section handles all of the profiles provided on the SD card, as well as any you've put there yourself. Profiles allow you to save your settings to load later. This is where you'll find CRT presets, since they're just saved profiles.

• For a list of Profiles provided on the SD card by default, head to the Profile Repository section.
• For a collection of Profiles made by the community not provided on the SD card by default, head to the Community Profiles section.

Load Profile

• Load From File - Selecting this will bring up a menu where you can navigate through the "profiles" folder on the SD card to load up a specific profile.
• Load Default - Loads the Default Profile. The Default Profile can never be deleted or overwritten.

The arrangement of profiles in the Load From File menu matches the internal file structure of the "profiles" folder on the SD card. This means that you can alter the folder structure to your liking if you don't prefer how they're laid out by default.

Save Profile

• Save Current - Overwrites the currently-loaded profile with the current settings. If selected while using the Default Profile, this will work like "Save As New" instead.
• Save As New - Saves the current profile as a new file named "New Profile X", where X is an ascending number. This will be located in the root "profiles" folder on the SD card, and can be renamed using a PC.

Assign Profile

This section of the menu allows you to assign one of the twelve number buttons at the top of the remote to a specific profile, using the same SD card navigation menu as the "Load From File" function.

Additionally, this is where you can assign a profile to be loaded up when the RetroTINK-4K is Powered Up. This is not the Default Profile, which can never be changed.

Advanced Settings

The following sections outline the Advanced Settings menu for the RetroTINK-4K.

Scaling and Cropping

The Scaling / Crop Setup menu is where you can crop and resize the image. Unlike the RetroTINK-5X, by default the RT4K sizes and positions the image based on the cropping, but this can be overridden with the Scaling Mode setting.

Input Crop

The RetroTINK-4K has robust controls to adjust size, positioning and cropping:

• "Top Trim" and "Bottom Trim" will effectively scale the image up and down in most Scaling Modes.
  • To more easily see the edges of the Top and Bottom Trims, set the Scaling Mode to "Auto Fill Integer".
• "Left Trim" and "Right Trim" will adjust the centering of the image, as the RT4K automatically centers the image based on these settings.
  • To shift the image left and right, increase the Left or Right trim to push the image in the opposite direction.

Vertical Pre-Scale

The RetroTINK-4K features the ability to "Pre-Scale" video content, or discard scanlines, at a fractional increment of the source input. Discarding vertical lines results in a loss of vertical resolution. This loss can be useful under certain circumstances, such as creating more accurate scanline rendering for 240p visual content output from consoles that run at higher resolutions (such as the Dreamcast or Wii).

RoTATE

RoTATE (pronounced "roh-tah-tay") is a special feature within the RetroTINK-4K to rotate the image 90 degrees clockwise (right) or counterclockwise (left). This is especially useful for games that may only display their image horizontally, such as many arcade shooters.

RoTATE Example
Standard Output	90 Degrees Right	90 Degrees Left

The RoTATE mode will only work if the samples per line of your video source is lower than 1024 samples per line (visible in the RGB/Component ADC menu).

• Because the video of Composite and S-Video is locked to 858 samples per line, no additional tweaking is required when using these input sources.
• Further, RoTATE mode will only work with 240p, 288p or 360p resolutions. This is important for titles that mix them with 480i.

If you're using RGB or YPbPr input, visit the RGB/Component ADC section of this page for information on ADC and decimation settings to meet the 1024 samples per line requirement. Similar limits apply when using HDMI® sources: use the Input Decimation settings in the "HDMI® Receiver" menu if the horizontal samples exceed 1024 (for example, MiSTer cores that use pixel repetition).

CP Auto Crop

The RetroTINK-4K can automatically crop and set aspect ratio for an input if it is fed a sufficient game screen (although this only works with RGB and Component sources).

Autocrop looks for the black edges of a game image and crops to them, so use a picture that clearly shows the edges of the video for best results. Screens that have any dark edges, as well as letterboxed, pillar-boxed, and window-boxed screens, are not recommended as they will fool the Auto Crop into thinking those are the edges of the image, resulting in an incorrect crop.

CP Auto Crop Settings

Name	Remote Button	Effect
Vertical Only	AUX 1	Automatically adjusts "Top Trim" and "Bottom Trim" to the top and bottom of the game image. Does not adjust Left Trim or Right Trim, and does not change Aspect Correction.
Full Crop to 4:3	AUX 2	Automatically adjusts Left, Right, Top, and Bottom Trim to the image, and changes Aspect Correction to "4:3 (PAR)"
Full Crop to 16:9	AUX 3	Automatically adjusts Left, Right, Top, and Bottom Trim to the image, and changes Aspect Correction to "16:9 (PAR)"

Scaler

The Scaler section in the RetroTINK-4K is where you'll find the tools that allow you to manipulate the geometry of the image.

Aspect Correction

The Aspect Correction setting chooses the Pixel Aspect Ratio, or "PAR", of the image. This is important because it needs to match the aspect ratio of the display the game is expecting to be seen on, referred to as the Display Aspect Ratio, or "DAR".

• NOTICE - The Aspect Correction controls are only available when the current Input (analog or HDMI®) is a resolution with a variable PAR factor, such as 240p, 288p, 480i/p, and 576i/p. Most other resolutions will lock the Aspect Correction setting to their expected PAR, no matter the input. For example, 720p over the PS3's Component cables will lock Aspect Correction to "1:1 (Sq. Pixel)", while 480p over PS3's HDMI® cables will let you choose yourself.
  • If the Aspect Correction controls are locked, you can still transform the image using the Scaling Factors tools.

The options that are available are:

Pixel Aspect Ratio	Description	Display Aspect Ratio Use-Case
4:3 (PAR)	Uses the common 4:3 Pixel Aspect Ratio, displaying the pixels slightly wider than squares.	Pre-HDMI® video game consoles, which expect to be displayed on the 4:3 DAR of CRT televisions.
16:9 (PAR)	Uses the 16:9 Pixel Aspect Ratio, displaying the pixels even wider than 4:3 (PAR).	Pre-HDMI® games and systems that offer widescreen modes, such as with the PS2 and the Wii.
1:1 (Sq. Pixel)	Uses the 1:1 Pixel Aspect Ratio, displaying the pixels as perfect squares.	Games and consoles that expect a 1:1 PAR but still output a sub-HD signal, such as PSP, and Game Boy games via the Super Game Boy or Game Boy Player.

If you're using a device that can use more than one Pixel Aspect Ratio, it's important that you set said device to correctly dovetail with the RT4K, so that the game will be shown correctly once it gets to your display.

Scaling Mode

Scaling Mode allows you to select automatic scaling modes or change aspect ratio constraints on manual scaling:

• Auto Fill - Fills the screen based on the selected Aspect Correction aspect ratio.
• Proportional - Allows the Vertical Factor to be adjusted while automatically adjusting the Horizontal Factor to keep the aspect ratio selected in Aspect Correction.
• Free-Form - Untethers the Vertical Factor and Horizontal Factor to allow values outside of the Aspect Correction setting. This setting lets you use the Vert. Factor and Hori. Factor settings to freely transform the image, like on the RetroTINK-5X.
• Auto Fill Integer - Scales the Vertical Factor and Horizontal Factor to the highest possible integer value without exceeding the screen boundaries, while also respecting the ratio selected in Aspect Correction. We highly recommend using the cropping tools to ensure the picture can be as large as possible while using this scaling mode.

Scaling Factors (Transform Tools)

The Horizontal Factor and Vertical Factor settings allow you to stretch and transform the image, either horizontally or vertically. Each factor diplays the multiplier value, the input resolution, and output resolution respectively.

Which of these are available depends on what option the Scaling Mode is set to. Proportional unlocks the Vert. Factor, while Free-Form unlocks both Vert. and Hori. Factors.

The function can be expressed as a simple formula: [Input Resolution] X [Multiplier] = [Output Resolution].

Horizontal and Vertical Factor Example
Axis	Multiplier	Input Res.	Output Res.
Vert. Factor	9.000	240	2160
Hori. Factor	2.045	1440	2945

Buffer

The RetroTINK-4K allows users to set how much video to buffer before outputting to your screen. The buffer, in conjunction with the Sync Lock mode, are the main determining factors for overall latency.

• Min. Lag - Sets the buffer to only store to bare minimum number of video lines. This option provides the lowest latency.
• 1/2 Frame - Always buffers half a frame.
• 1 Frame - Always buffers a full frame.

Min. Lag is typically compatible, but if you encounter an edge case with screen tearing, try setting this to "1/2 Frame" or "1 Frame".

Note that certain movie modes, such as Inverse Telecine, will automatically force the RetroTINK-4K to buffer a full frame.

Masking Color

The masking colour settings allow you to adjust the colour of the mask that displays in the Scaling/Crop menu. By default, the values a 0 Red, 0 Green and 31 Blue. You can also change whether the masking colour is displayed in the cropping menu only, or always (even when the RT4K menu isn't displayed).

Processing and Effects

The Processing / Effects Setup menu is where you can adjust the pixel interpolation, as well as add Scanlines and CRT Masks.

Where are the Scanline Presets?

If you're a regular user of the RetroTINK-5X, you may be surprised to enter this menu and find that there's no Presets available to choose from. This is because they are stored as Profiles on the SD card.

• To load an included CRT Preset, head to the main menu, then go Profiles > Load from File > HDR CRT Simulation, then pick one you want to use.

The "bundling" of CRT Presets as Profiles may seem odd to users of the RetroTINK-5X (where CRT Presets could easily be applied to optimal sampling profiles), however this shouldn't have much impact on the final result. CRT displays are inherently a bit blurry as part of their aesthetic (even PVMs and BVMs), so generic sampling is perfectly acceptable to use for them. If you're using a digital source and decimating it (like Nintendo Switch Online or an HDMI® modded system), you may want to simulate the blur using the Horizontal Interpolation Kernel, and / or the Horizontal Blur function.

The only exception to the above is when you're using the LCD scanlines, as the thin lines dividing each pixel won't appear correctly without scaling the image up by a flat number (such as 4.000x or 5.000x).

Interpolation

Vertical and Horizontal Kernel

Interpolation in relation to video processing is a technique to create more visual information on the output that is given on the input. These processes help make a more visually cohesive image, and reduce effects such as shimmering when the image is scrolling. The RetroTINK-4K offers a handful of interpolation options that can be applied independently across the vertical and horizontal axis.

• Bilinear Sharp - The image is scaled up the maximum integer factor that is within the output size using Nearest Neighbor followed by a bilinear scale to the final output size. This option provides sharp pixels without shimmer at non-integer scaling factors.
• Bilinear Medium - The image is scaled up 2x using Nearest Neighbor followed by a bilinear scale to the final output size. This option is somewhat softer than Bilinear Sharp but still sharper than regular Bilinear.
• Bilinear Std - The image is scaled using conventional bilinear filtering.
• Bilinear Soft - This performs linear interpolation over 4 pixels instead of the standard 2 pixels resulting in a very soft image. This may be desirable to produce horizontal blur for CRT effects
• Cubic - Interpolation using the bicubic spline kernel which outputs an image sharper than bilinear but softer than Lanczos.
• Lanczos2 and Lanczos3 - Interpolation using the Lanczos family of scaling algorithms. Lanczos is a popular algorithm that provides good results for natural imagery (i.e. movies) and most 3D games.
• None - The image is scaled using Nearest Neighborfor completely sharp pixels, but may shimmer if the Scaling Factors are not set to even multipliers (ie set to non-integer factors).

Anti-Ringing

Anti-Ringing is a toggleable option (On / Off) to reduce the appearance of ringing artefacts when using the Lanczos family of interpolation kernels. By default this setting is set to On, but even then it won't actually be engaged unless you're using Lanczos2 or Lanczos3.

Linear Light

Linear Light is a method of image color and brightness reproduction that may provide more accurate scaling and blending. Linear Light will also alter the appearance of scanline effects, which users may consider an improvement or not based on subjective preferences.

• Linear Light On - The RetroTINK-4K performs inverse gamma mapping at the start of the scaler pipeline and performs all operations in the linear light domain. The output is gamma encoded for SDR modes and PQ encoded for HDR modes.
• Linear Light Off - The RT4K performs all scaler operations in the gamma domain and only performs inverse gamma at the output if needed for color gamut transforms.

Assuming default SDR settings, for linear light to function properly, you have to manually set input factor and output factor to 2.4 in the Color Correction-> Gamma/PQ menu.
Enabling HDR in HDMI® Output->Transmitter, Enabling Color Space Conversion in Color Correction->Color Space Conversion, or Adobe RGB/P3 in HDMI® Output->Colorimetry will adjust Gamma/PQ settings by default to properly allow Linear Light processing.

More information on the benefits of linear light can be found here.

Scanlines

The RetroTINK-4K has customizable scanline generation which can recreate the look of various displays, including early LCD displays. Scanlines are an effect that simulates the appearance of blank scanlines on a display, similar to what you might see on older cathode ray tube (CRT) monitor or television screens. The effect creates generates black spaces between each visible scanline of video, simulating how lower resolution progressive signals would be presented on higher resolution (480i) displays.

Since scanlines are part of the image drawn by a CRTs red, green and blue electron gun, they scale with the image's pixels, and it's for this reason that the RetroTINK-4K's scanlines behave the same. This means that scanlines will appear thinner depending on the resolution of the input source; 240p scanlines are much thicker than scanlines placed on a 1080p input.

• For clarity, on a CRT, every line drawn on the display is a scanline. 240p however only uses half of these, resulting in blank scanlines every second row. This causes the scanlines to be perceptible, hence why these blank lines are called "scanlines" despite not being anything at all.

Note: Proper simulation of CRT and LCD effects involves many more factors than just the scanline settings, such as but not limited to: Scaling, ADC Sampling, Interpolation / Filter and Color Correction. If this is overwhelming, please try one of the pre-made profiles first (included on the RetroTINK-4K SD card).

Blank / Black Scanlines

This scanline function determines what formula is used by the scanline generator to translate the replaced video scanline to a "blank / black" scanline.

• Off - Disables the scanline generator. Further settings in the Scanlines section will not have an effect if Off is selected.
• Exponential - A scanline pattern that has the softest profile from bright to dark.
• Gaussian - A scanline pattern similar to Exponential, but with a sharper transition from bright to dark.
• Super Gaussian - A scanline pattern with a very sharp transition from bright to dark.
• Linear - A scanline pattern with a straight ramp from bright to dark.
• Box - A scanline pattern similar to old style emulator scanlines, with no blending from bright to dark. The scanline pattern is either completely on or completely off.

You can adjust the scanlines with the next two settings:

• Strength - Adjusts the maximum width of the scanline effect.
• Modulation - Adjust how much the thickness of the scanline effect will change depending on brightness. Specifically, the higher this value, the thicker the black scanlines will be around dark areas of the picture.

If you're inputting an interlaced signal, you should consider going to the Deinterlacer/Film menu and setting the Algorithm to "CRT Simulation". This will cause the scanlines to move up and down every frame, giving a look authentic to how these interlaced signals appear on a real CRT.

LCD Effects

The LCD functions behave differently than the "blank / black" functions, and are instead designed to simulate the appearance of older LCD displays.

• LCD Mono - Will place a 1x1 pixel border around every upscaled pixel in the image.
• LCD RGB - Simulates RGB subpixels per each upscaled pixel (similar to how the CRT masks simulate phosphor artifacts).

LCD effects will not look correct unless the both the Vert. and Hori. Scaling Factors have been set to even multipliers (such as 4.000x or 5.000x). LCD RGB looks best if both the Vert. and Hori. factors are the same multiplier.

With LCD functions selected, the Strength and Modulation options change to "LCD Subpixel Str." and "LCD Vert Str.", respectively, and will retain their values. Despite being available for both LCD functions, they only have any effect on the LCD RGB effect.

• LCD Subpixel Str. - Sets how strong the LCD subpixel masking is. Lower values will more strongly "tint" the subpixels the colour of the upscaled pixel they represent.
• LCD Vertical Str. - Controls the size of the horizontal line under each pixel.

Color Bleed

Color bleed simulates some of the imperfections of how colors were presented on a CRT. These won't do anything unless a scanline generator is enabled; these won't work with the LCD effects.

• Red Bleed: Enabling Red Bleed simulates a common CRT effect where the Red beam is softer and less focused than Blue and Green.
• Red Convergence: Adjusts a vertical offset of the red data within the scanline effect. Can be adjusted from a -10 to 10 offset.
• Blue Convergence: Adjusts a vertical offset of the blue data within the scanline effect. Can be adjusted from a -10 to 10 offset.

Masks

Masks apply effects equivalent to the shadow masks on a CRT (as well as the similar aperture grilles and slot masks). Since these masks were metal plates that spanned the entire surface of a CRTs glass screen, they're independent of the image drawn by the red, green and blue electron guns. For this reason, masks on the RetroTINK-4K behave the same, and so will NOT adhere to the subpixels of the input you've selected.

The RetroTINK-4K accomplishes the mask effect by tiling an image across the entire screen at 1:1 sizing. Because of this, reducing the RT4K's output resolution will increase the size of the masks.

• Enable - Turns masks Off or On.
• Strength - Adjusts the strength of the masks. "+0" is the neutral value, "+10" is the maximum value, while "-10" is equivalent to turning Masks off.
• Load from File - Takes you to the "masks" folder of the SD card

If you want to make your own masks, head for the Custom CRT Masks section of this page.

Horizontal Blur

The Horizontal Blur function approximates the horizontal blurring present in some CRTs, looking rather like the right-to-left smearing on "3CHIP" Super Nintendos.

• Function - Can be set to "Off" or "IIR LPF".
• Cut-Off Freq - Adjusts the strength of the horizontal blur.

If you're wanting to blur the image in a more "traditional" sense, you'll want to use the Interpolation Kernels in the Processing/Effects menu.

Color Correction

The Color Correction Setup menu controls the advanced color gamut correction and adjustment options on the RT4K. Information on the Custom Color Matrix preset format can be found here.

Gamma and PQ

The input controls adjust how incoming RGB signals are converted from gamma space to linear light.

• Input Factor: Factor used to convert the input from gamma space to linear light. Input factor is the inverse gamma exponent. Can be adjusted between 0.10 and 5.00.
• Input Lift: Lift adds an offset (raises or lowers black level) to the input gamma conversion. Can be adjusted between -1.00 and 1.00.
• Input Gain: Gain multiplies the output of the input gamma conversion. Can be adjusted between 0.00 and 10.00.

For SDR output modes, the output factor is used to re-encode the linear light signal back to the gamma domain using the specified exponent.
For HDR modes, the SMPTE 2048 PQ (Perceptual Quantizer) is used to tone map the linear light signal into a HDR signal. The PQ can be adjusted in units of nits, where the specified nits represents the maximum brightness of the tone mapping.

• Output Factor: Factor used to convert encode the output of the video pipeline back to gamma space. Can be adjusted between 0.10 and 5.00.
• SMPTE 2048 PQ: For HDR output mode, the RT4K uses a perceptual quantizer instead of simple gamma. The control sets the maximum brightness of the PQ in units of nits. Can be adjusted from 250 to 10,000.

Color Space Conversion

• Apply Preset: Opens the Load CSC Matrix menu, where users can load any saved CSC profiles from the SD card. Most use cases will involve simply applying a preset from the SD card, for example, to apply a color gamut correction to emulate a PVM. The RetroTINK-4K 1.0 SD Card release includes many presets. You can explore the included CSC presets here [link to \csc page].
  

• Custom Matrix: Allows the user to turn On or Off CSC by enabling/disabling the Input RGB to XYZ conversion matrix and settings applied to the Gamma/PQ.
• Prevent Clipping: Automatically scale the CSC matrix so that highlights are not lost at the cost of making the image dimmer. Can be set to On or Off.
• Saturation: Controls the color intensity. Lowering it turns the image black and white. Raising it makes the colors more intense. Can be set from -1.0 to +1.0.

Input RGB to XYZ

The user can manually adjust the matrix used to convert the input RGB data into XYZ colorspace. The RT4K automatically chains to correct conversion from XYZ to output RGB depending on the specified output colorimetry (e.g., BT709, BT2020, Adobe RGB, etc.). Each of the conversion functions can be adjusted between -1.75000 to +1.75000.

Advanced Controls

• Transfer Function: Can be set to "sRGB 0.055", "Rec.601/709 0.099", "SMPTE 240M 0.1115" or "Gamma". The various transfer functions linearize the low-end of the gamma curve to avoid bit loss. "Gamma" uses a simple gamma encoding.
• Bit Crush: Lowers the number of colors in the core video signal by reducing the number of bits per color. This is primarily intended for removing rounding errors that can occur in the original signal, e.g. when using GBI, as well as potentially removing noise in some limited cases. Alternatively, it can be used for aesthetic purposes to create a posterization or limited-color mode effect.

Black Frame Insertion (BFI)

Black Frame Insertion (BFI) is a technique to improve motion clarity with high refresh rate monitors. As an example, a 60fps video source played on a 120hz monitor could have a black frame interstitially placed between every frame. The resulting "image-black-image-black" pattern can increase the perception of motion and fine details. If you have a higher refresh rate monitor, a customizable example can be viewed over at Blur Busters.

BFI cannot be enabled unless the following two requirements are met:

• Set a supported Output Resolution and frame rate - Due to bandwidth constraints, BFI is limited to 1440p or lower resolution output. This also must be a high frame rate: either 100hz or 120hz.
• Set a supported Sync Lock Mode - BFI also cannot be enabled unless you are in Gen or Frame Sync Lock mode.

If both of these requirements are met, the BFI options will be unlocked.

• LCD Saver: LCD display panels may suffer from image retention when using BFI. The LCD Saver helps prevent this by inverting the order of (video frame)-(inserted frame) at the timer value set. LCD Saver can be set to 0, 1, 5, and 10 Minutes. When the frame order is inverted, it may create a momentary glitch in the video output. Note that setting the time value to 0 will display a message screen warning the user of possible LCD panel image retention.

BFI Control

Black Frame Insertion (BFI) Settings

Strobe: Strobe controls how the output frame rate is divided into the input frame rate. As depicted in the diagram, with Strobe 1, the 60Hz input frame is flashed one time at 240 Hz. At Strobe 2, the 60Hz input frame is flashed twice at 240Hz, with black frames in between. Alternatively, a 60Hz source within a 120Hz output would display for 1/2 of the time 120Hz output window. Blur: Blur is a duty cycle modifier that works in relation to Strobe to change how many frames the source video is presented in relation to the black frames. In the example diagram (60Hz Source inside a 240Hz output), a Blur of 1 would display the source video 1/4 of the 240Hz window, a Blur of 2 would display the source video 2/4 of the 240Hz window, and a Blur of 3 would display the source video 3/4 of the 240Hz window. Some relationships of Blur and Stobe are locked, such as a 60Hz video source in a 120Hz output window, which would only allow a Blur of 1 (1/2 of the output 120Hz window).

More information about BFI can be found at Blur Busters.

BFI Color

The BFI Color settings allows the user to change how the inserted frame appears.

The Blending Mode setting selects between the following functions:

• Solid: Creates a grayscale inserted frame that can be adjusted with any of the Red, Green or Blue BFI Color settings. A lower BFI Color numerical value is darker, higher is brighter.
• Alpha: In this mode, the inserted frame is a duplicated video frame with a transparent alpha overlay darkening the inserted frame based on the BFI Color setting. A lower BFI Color numerical value is darker/more opaque, a higher value is brighter/less opaque.
• Solid Color: Sets a solid inserted frame with an RGB-assignable color from the BFI Color selections.
• Alpha Color: Inserts a duplicated video frame with an alpha color overlay. The color of the alpha-blended frame is set from the R-G-B BFI Color values.
  

The Red, Green and Blue BFI Color values allow for customizable colors in the Solid Color and Alpha Color modes, and are an interlocked numerical valued for Solid and Alpha blending modes (R-G-B values cannot be adjusted separately).

Deinterlacer and Film

The Deinterlacer / Film Mode Setup menu allows you to adjust settings for use on interlaced sources, such as deinterlacing methods and Inverse Telecine.

While tweaking the options under the Mode and Motion Adaptive Settings sections, we suggest using the Pause Button to pause the video on a frame with motion. This will allow you to see the effects of the deinterlacing more easily.

Mode

There are six deinterlacing algorithms to choose from:

• Motion Adaptive - Uses an algorithm to determine whether to use Bob deinterlacing for areas of the screen that change, or Weave deinterlacing for areas that stay the same. Can be further tweaked in the Motion Adaptive Settings section.
• Weave - The current field remains on-screen while the next field is drawn, 'weaving' the two fields together. This is the same as 'disabled' in video players such as VLC, and will result in combing artifacts.
• Bob - Doubles the vertical height of each line to fill the full frame. This causes the image to appear as if it's moving up and down, since the two fields are not aligned in the interlaced signal, but preserves temporal resolution of interlaced video.
• Linear - Linear interpolated Bob (i.e., rather than a pure linedouble, line 2 is the average of lines 1 and 3, line 4 is the average of lines 3 and 5, etc.).
• Blend - The frame is created by averaging lines from the two most recent fields. Produces ghosting.
• CRT Simulation - Similar to Bob, but additionally changes scanline behavior to match that of interlaced content on a real CRT. If Scanlines have not been enabled, this mode will appear identical to Bob. See below for more details on this algorithm.

CRT Simulation

The CRT Simulation algorithm is unique enough to warrant its own section. It's used to to simulate the way 480i content is displayed on a real CRT: each frame of a 480i image is actually only 240 lines, and each new frame switches to using lines that were unused in the previous frame. Because of this, CRT Simulation will appear identical to Bob deinterlacing unless you use one of the Scanline functions enabled in the Processing / Effects menu (since they simulate the unused lines), and are viewing interlaced content.

CRT Simulation will also cause your crop settings to be displayed incorrectly, so be prepared to redo your crop after enabling this feature.

• There is one thing to keep in mind when using this feature: the output frame rate of the RT4K must match the input signal's frame rate in order for the effect to be displayed correctly. This is important if you're using a PAL system, which run at 50 frames per second: if the RT4K is outputting at 60fps (as it usually does by default), the CRT Simulation will not appear correctly for PAL content!

Motion Adaptive Settings

Motion Adaptive settings apply only to the Motion Adaptive Deinterlacing mode, allowing you to adjust how the Motion Adaptive Deinterlacing operates.

• Sensitivity: Adjusts the sensitivity of Motion Adaptive, between "Min", "Medium", "High" and "Max". The higher this is set, the more weaving will be present for moving parts of the screen, at the benefit of a stabler look for static parts of the screen. Many games will look just fine on the Min. setting, however several games may require Medium or higher. For example, Burnout 3: Takedown on PlayStation 2 has a subtle flickering and noise-like dithering that throws off the Motion Adaptive Deinterlacer for still parts of the screen.
• Noise Threshold: Adjusts how much low-level changes are ignored, so that the deinterlacer doesn't fall back to Bob deinterlacing unnecessarily. Useful for content that has noise and / or dithering present.
• Interpolator:Controls how the Bob function of the deinterlacer is calculated. The bob is either taken from the line above (Upper Field), line below (Lower Field) or the Average of the upper and lower lines.
• Detector: Can be set to "Zero-Lag", which favors the most current field. "Symmetric" favors the previous field, but allows for symmetric motion detection, which may provide cleaner results.

Bob Settings

The only Bob Setting here is the Bob Offset, which adjusts adjusts how far apart each field is from each other. It can be set between "-3" and "+3". This setting is useful for 240p games that were poorly ported to run at 480i, such as Mega Man Anniversary Collection on PlayStation 2.

Film Mode

The settings under Film Mode contain options to help process video content.

Inverse Telecine:

• 3:2: In this mode, video content that was 24hz sources converted to 60hz interlaced signal will play back in a reconstructed 24 fps. This helps applicable video content play with its intended cinematic framerate.
  
• 2:2 In this mode, the deinterlacer will rebuild progressive video output from 480i games that run at reliable/stable 30 fps, which can effectively convert 480i into 480p. This will result in an increase in visual resolution and clarity. This is especially useful for PlayStation 2 where much of the library is 480i only.
  

Dejudder 24hz: This mode treats telecine material as a virtual 24hz source when using Gen lock and Frame lock Sync Lock, allowing for true 24hz output when combined with a 24hz output modeline. This option only applies when a 3:2 source is successfully detected / deinterlaced.

Cadence Detection

The cadence detection menu offers controls to adjust the RetroTINK-4K's detection of content to pass to the the inverse telecine functions.

• Motion Digital, Motion CP, and Motion SDP: These values change the noise threshold for HDMI inputs, component/RGB inputs and composite/S-video inputs, respectively. Adjusting the noise threshold higher will decrease the detection of false positives, but may miss weaker or nosier telecine signals. Adjusting the threshold lower may increase false readings but allow less stable signals to be processed. Each value can be set from a range of 0 to 500.
• Threshold: Once a signal passes the check of the Motion thresholds, the Threshold number sets how many consecutive detections of a telecine pattern are required before the deinterlacer function activates. This may be helpful for noiser sources such as VHS to further filter out false detections.

HDMI® Receiver

The HDMI® Receiver Setup menu is where you control how the RT4K handles HDMI® In video. This menu is only functional when the HDMI® In port is the currently selected Input. If it is, this menu can be quickly accessed by pressing the ADC button at the top of the remote when HDMI® is selected as the input.

Input Decimation

Input Decimation

Input decimation is a function to reduce the horizontal resolution of a given HDMI input. This works by taking the current input horizontal resolution, and reducing it as a division between the Input Pixels and Output Pixels settings. A display of the final output resolution after decimation has occurred is shown in parenthesis at the end of the Input Pixels field. Input Pixels: Sets the number of sample width pixels to generate a decimation from. Output Pixels: Sets how many pixels to divide the sample width into. Initial Phase: Sets the phase offset for the decimation, determining which pixels are preserved and which pixels are removed.

Colorspace

Colorspace has options to assign what colorspace the HDMI® input is using, as well as what method to use for 4:2:2 upsampling.

• 4:2:2 Upsampler: Determines how to process digital inputs that are using 4:2:2 chroma subsampling. Can be set to "Linear", which uses a bilinear filter for a smoother appearance, or "Nearest", which uses a nearest neighbor filter for a sharper look (but with more obvious aliasing).
• Input Range: Determines what color range to process the incoming digital signal as. "Auto" should be used unless there is a specific colorspace mismatch. Other settings include "RGB Lim.", "RGB Full", "YCbCr 601", "YCbCr 709", "XUYCC 601", "XUYCC 709", "YCbCR 601 (Full)" or "YCbCR 709 (Full)".

Misc

• A/DAC Mode: Allows Analogue consoles that support the Analogue DAC to output an unscaled image to the RT4K.
  
  • Off: The Analogue console sees the RT4K as a regular HDMI display.
    
  • NTSC: The Analogue console sees the RT4K as an Analogue DAC with the region switch set to NTSC.
    
  • PAL: The Analogue console sees the RT4K as an Analogue DAC with the region switch set to PAL.

PLEASE NOTE: While using A/DAC mode, the connected Analogue console will output 240p with horizontal variable pixel repetition, in order to allow for cases such as SNES 512-column mode to be rendered correctly. This may cause some scaling settings to not behave how you expect. Nothing is broken, please adjust Input Decimation and Scaling/Cropping until you get the desired image, noting that the initial horizontal scale is 4x what you are probably expecting (2x if you're playing a game that uses 512-column mode), and THIS MAY CHANGE IN THE FUTURE. Additionally, A/DAC Mode when set to PAL will require manual aspect ratio adjustment, and when set to either NTSC or PAL will require significant cropping when used with the Mega Sg due to the Mega Sg's output having a significantly exaggerated overscan area. Due to limitations both with Analogue hardware and with our understanding of the Analogue DAC, none of these issues can be addressed automatically at this time. Finally, please also note that, like with the actual Analogue DAC, changing the A/DAC mode setting while your Analogue console is connected and turned on will result in improper operation from your Analogue console, and is not recommended.

RGB and Component ADC

The RGB / Component ADC Setup menu is where you control how the RT4K handles analog inputs, such as the RCA, S-Video, HD-15 and SCART ports. This menu is only functional when an RGB or Component input is in use. If that is the case, this menu can be brought up by pressing the ADC button at the top of the remote when YPbPr, RGBS, RGsB, or RGBHV is selected as the input.

Sampling (ADC)

Sampling (ADC)

Samples per Line: Adjusts the total number of samples taken per line of video. When Samples per Line is set to a multiple of the pixels per line in a particular video source, the image will appear sharper as the pixel edge boundaries are aligned with the ADC sample rate. The parenthetical information after the Samples per Line shows the active, visible samples. Decimation Factor: Decimation divides the Samples per Line by the Decimation Factor value. For instance, if your Samples per Line is 1716, a Decimation Factor of 2 would leave 858 remaining samples. The parenthetical number after the Decimation Factor displays how many samples are remaining after decimation. Decimation Phase: Phase determines which set of samples is preserved when Decimation is active, and which set of samples is discarded. The selection will be a single instance of the Decimation Factor, I.E, If Decimation Factor was 3, you could choose between 1,2 or 3 Decimation Phase selections. Decimation Phase is disabled if Decimation Factor is off. Sub-Phase:A fine-tuning calibration to control the exact timing for when samples are taken. A calibrated Sub-Phase will result in a sharper image. This can be manually set or the alignment can be set with the Auto Phase function. Sub-Phase can be a value of 0 to 348.75 degrees, with 11.25 degree increment selections. Anti-Alias LPF: Applies a low pass filter the incoming analog signal before the signal is sampled by the ADC. This can help eliminate analog signal interference in the video, but may result in a less sharp image at higher settings. Auto setting will attempt to apply an appropriate setting based on the signal's sampling rate. Can be set to "Auto", "9MHz (Strong)", "16 MHz (Med)", "35 MHz (Light)", "95 MHz (Min.)" and "Off".

Sync (ADC)

• SoG Threshold: Sets the voltage level used to slice the video signal and generate a digital sync pulse. Adjusting this level may help with problematic sources. The volage can be set between "0.00 mV" and "327.42 mV" in in 11.29 increments.
• Pre-coast: Sets the number of lines before vertical sync to switch from syncing with video source to internally generated sync. Can be set between 1 and 31 lines.
• Post-coast: Sets the number of lines after vertical sync to switch from syncing with video source to internally generated sync. Can be set between 1 and 31 lines.

The coast settings create a padding area away from the vertical sync pulse, so syncing to the horizontal doesn't encounter errors from off-spec signals or glitchy signal transitions. Adjusting Pre-coast and Post-cost values may be helpful when processing off-spec video sources.

• Slow-lock: Slows down the detection of new resolutions. May increase the glitch time between 240p/480i transitions but may help with locking on to problematic sources.

Gain

• Pre-ADC: Changes the amount of analog gain applied to the signal before the ADC, functioning as a coarse contrast adjustment. Can be set between -0.7 and +0.8.
• Red,Green, and Blue allows fine adjustment of the individual color channel digital gain, functioning as a finer contrast adjustment per color channel. Can be adjusted between 1.000 and 1.996.

Offset

• Red,Green, and Blue offset provides per color black level / brightness adjustment. Values can be set between -100 and +100.

Auto Calibrate

Auto Phase

Any game screen is sufficient for automatic phasing, but it is recommended to use the 240p Test Suite or other sufficiently patterned screen for eyeballing results. whether you've set automatic sample detection using that menu, or you manually selected Decimation Factor in the ADC page, selecting Auto-Calibrate Phase makes the RetroTINK-4K automatically select the best Decimation Phase and Sub-Phase for your current picture and should give you the sharpest results. It is recommended you run this 3-5 times to make sure the same factors and phases are consistently chosen.

Auto Gain

The Auto Gain function will calibrate the gain levels for the current input, however it only works for RGB and YPbPr sources.

• To use Auto Gain, go to a game screen which has a patch of colour that should be pure white. When you enable the Auto Gain function, the RT4K automatically calibrates the Gain levels based on that white patch.

Auto Gain only works in calibrating the overall brightness Gain, not the individual color gain. You may need to manually adjust the individual colors a few ticks more for in the Gain section to get the true RGB code (255) for a given color. We highly recommend the use of the 240p Test Suite for this task.

Auto Gain must be calibrated on a per-console basis, meaning it will need to be set between different systems. This applies even across different units of the same system, such as two Super Nintendos, as their picture output will have degraded slightly differently.

Sample Rate Detection

The Sample Rate Detection menu is where you control how the RT4K automatically detects the sample rate of a given analog source. This menu is only functional when an RGB or Component input is in use.

Sample Rate Detection Overview

The RetroTINK-4K can take advantage of sampling and scaling algorithms to seamlessly change settings when it detects a horizontal resolution change. This is useful for some analog retro gaming consoles, but requires knowledge of their "Master Sampling Rate." Please consult the table below to see which resolutions are available for consoles where automatic sampling detection is recommended.

Master Sampling Rate Chart (NTSC)

Console Name	ADC Sample Rate	Decimation Factor & Total (Active) Resolution
		1/10	1/8	1/7	1/6	1/5	1/4
Super NES	3410	341.000 (256)				682.000 (512)
Sega Genesis/Mega Drive	3420	342.000 (256)	427.500 (320)
Sega Saturn (WIP)
Turbo Grafx 16/PCEngine	2730		341.250 (256)				682.500 (512)
Sony PlayStation	3413	341.300 (256)	426.625 (320)	487.571 (384)		682.600 (512)	853.250 (640)
Sony PlayStation 2	3432	343.200 (256)	429.00 (320)	490.286 (384)		686.400 (512)	858.000 (640)

Master Sampling Rate Chart (PAL, if different)

Console Name	ADC Sample Rate	Decimation Factor & Total (Active) Resolution
		1/10	1/8	1/7	1/6	1/5	1/4
Sega Genesis/Mega Drive		(256)	(320)
Sega Saturn (WIP)
Turbo Grafx 16/PCEngine			(256)				(512)
Sony PlayStation		(256)	(320)	(384)		(512)	(640)
Sony PlayStation 2	3456	345.6 (256)	432 (320)	493.714 (384)		691.2 (512)	864 (640)

Once you know the master sampling rate of your console, set that console's ADC Sample rate in the "Sample Rate Detection" menu under ADC Sample Rate, and turn both "Auto Dec. Factor" and "Auto Dec. Phase" to "On." Once you enable those options, if you know which resolutions you'll use, scroll down to that resolution to enable that horizontal resolution's detection and the RetroTINK-4K should automatically switch to a different set of settings whenever it detects that particular resolution is used. This process will help automatically set Decimation Factor and Decimation Phase in the ADC setup.

Note: You may be tempted to turn on every resolution, but if you know your console won't use it, consider turning that resolution off to help with the detection speed.

Control

• Auto Dec. Factor: Turns on Sample Rate Detection
• Auto Dec Phase: Turning this on makes the RT4K select phase for you. This disables the Decimation Phase setting in the ADC menu.
• ADC Sample Rate: Tells the RT4K how many samples to take in each line.

Progressive Detection & Interlace Detection

Each line shows the result of the ADC Sample Rate divided by a different Decimation Factor: 10, 8, 7, 6, 5, and 4, respectively.

SDP Decoder

The SDP Decoder Setup menu is where you control how the RT4K handles Composite and S-Video. This menu can be quickly accessed by pressing the ADC button at the top of the remote when S-Video or Composite are selected as inputs.

Gain and Balance

• Brightness: Adjusts the brightness of the image. Can be set between "-100" and "+100".
• Contrast: Adjusts the contrast of the image. Can be set between "-100" and "+100".
• Chroma: Adjust the saturation of the image. Can be set between "-100" and "+100".
• Phase: Adjusts the tint of the image.
• Blue Only: Displays a greyscale depiction of the blue colour values, with white being full blue and black being no blue.
• Setup: Can be set between 0 IRE and 7.5 IRE.

Processing

These controls will adjust how the RT4K handles the processing of the Composite signal.

• Y/C Filter: Can be set to "2D Adaptive", "2D Fixed" and "Notch". Settings determine the method that the luma and chroma components of the composite signal are isolated.
• Comb Bandwidth: Comb bandwidth determines how much detail to try to preserve when separating luma and chroma components. Higher bandwidth maintains more detail but also introduces more artifacts.
• Chroma Bandwidth: Controls a low pass filter on the chroma signal, may help to remove rainbowing and other artifacts.
• Sharpness: Artificially sharpens the image. Can be set between "0" and "15".
• CTIE: Can be set between "0" to "3". CTIE sharpens the chroma channels using the luma channel as a guide.

Sync (SDP)

Adjusts how the RetroTINK-4K syncs and locks onto the Composite signal.

• H-Lock Speed - Can be set to "Auto", "Slow", "Medium" and "Fast".
• Standard - Changes the analog signal standard. Can be set to "Auto", "NTSC", "PAL", "SECAM", "NTSC-443", "PAL-M", "PAL-N" and "PAL-60".

Audio Input

The Audio Input Setup menu is where you'll find options regarding the RT4K's handling of audio, such as the sampling rate and overriding which audio input is in use. More information can be found in the Alternate Audio Inputs and Inputs section.

Sampling (Audio)

• Sample Rate: Set the RetroTINK-4K's audio output sample rate. You can choose either 48khz and 96khz.
• Pre-amp Gain: Boost or attenuate the audio output gain. Can be set from -24dB to +28dB.

Source

• Input Override: Here you can override the current audio source with an alternate input, choosing between RCA, HD-15, SCART, Front S/PDIF or Off.
• Input Swap: Allows you to enable mono to stereo function (1 signal to two speakers) with Mono (left) and Mono (right) selections, or swap the left and right audio channels with the L/R Swap selection.

System

The System selection of menus relate to the RetroTINK-4K itself, including the On-screen display, firmware updates, and displaying various status screens.

OSD and Firmware

Banner Image

This menu allows you to load in your own Banner. The SD card comes pre-loaded with a default RetroTINK-4K banner, FirebrandX's banner displaying Firebrand from Demon's Crest, and two moon banners (both of which intentionally do not display the moon in a perfect circle).

Here's some information on how banners work on the RT4K:

• Banners are stored in the "image" folder of the SD card.
• Banners must be 24-bit BMPs in order to work with the RT4K.
• 320 x 128 is the recommended pixel dimensions. It can be larger, however only the upper-left 320x128 pixels of the image will be drawn.
• An RGB value of "255, 0, 255" (a pink colour) will be treated as transparency.
• If a Profile doesn't have a banner image specified, the file named "default.bmp" will be loaded instead. This lets you determine your own default banner image.

On Screen Display

This section allows you to adjust facets of the On Screen Display, including the menu.

• Position - This lets you set whether the menu is displayed on the Left side of the screen, the Center, or the Right side of the screen. This is set to "Left" by default.
• Auto-Off - Lets you determine how long the menu will wait before disappearing (as if you pressed the menu button). This is set of "Off" by default, but you can set it to turn the Menu off after up between 10 - 100 seconds (and anything in-between in 10 second increments).
• Hide Input Res. - Turning this on will mean the RT4K will not display the current input and resolution in the top-right corner of the screen every time it changes. This is useful if you're capturing or streaming games that switch resolutions.
• Enable Debug OSD - This option allows you to permenantly display one of the three Status Pages or the Diagnostic Console.

Firmware Update

This option allows you to Check the SD card for the two files needed for installing new firmware to the RetroTINK-4K. For more information on how to install new firmware, head to the Firmware Updates section.

Status

Displays the Status menu, letting you learn more about the current status of the RetroTINK-4K. For more information, visit the Device section of our GUI Map.

Diagnostic Console

Shows the 30 most recent actions in the RetroTINK-4K's operations. Or something?

About

Displays the About Page, containing the following information:

• About
  • Device - Displays information about the RT4K's hardware version.
  • FW Version - Displays the current firmware name.
  • Device ID - Displays the ID of the RT4K.
• Resources
  • Website - www.retrotink.com
  • Discord - discord.gg/jE6deAhjCM
  • Wiki - consolemods.org/rt4k
• Special Thanks To:
  • RetroRGB - GameSack - FirebrandX - Wobbling Pixels - Extrems - CouryC - John Linneman - Try4ce - Artemio - Blur Busters - Voultar - Old Kid - MinotaurZombie - teen Nick - Chungo - Mr. Moro - Guspaz - SquidHominid - Mizox - blizzz - Supercowabunga - KBABZ - Jeff Chen - pram0d - atrac17 - Cyo - 8bitesquire - Fenris Wolf Retro - Ace - Kuro Houou - ScarletSprites - wizzo - CGQ - TechnicalMonkey - EposVox -Derf - IceStrike256
    • Names are ordered to favour formatting, and are otherwise in no particular order.
      

SD Card And Profiles

The RetroTINK-4K includes an SD card with a set of Profiles, CRT Masks, Color Correction Profiles and more from the talents of FirebrandX, Wobbling Pixels, Exrems, Kuro Houou, pram0d, Cyo, MrMoro, austinbroth, Chungo, and (anyone else I'm forgetting). This area includes a mirror to download the stock RetroTINK-4K 1.0 Full SD Card, as well as a comprehensive list of every profile included with the release.

SD Card Version 1.0

A copy of the 1.0 SD Card, including the stock firmware and included profiles, can be downloaded here: File:Rt4k 10rc26.zip.

Profiles Version 1.0

A comprehensive list of every profile included with the 1.0 launch release can be found here.

System Specific Settings

System-Specific Settings is all about highlighting how you can use the RetroTINK-4K's various features to improve the experience of using your video game systems beyond just plugging them in. This can range from setting 1:1 pixel aspect ratio for Super Game Boy on the SNES, to dovetailing with the Sharpscale Plugin on the PlayStation TV.

• Due to its sheer size, this section has been broken out into its own subpage, which can be found here.
  

Additional Guides

Custom CRT Masks

The RT4K allows for the use of custom CRT mask overlays via the Masks menu. This is primarily intended to give an effect similar to CRT shadow, slot and aperture masks that stretch across the screen (as opposed to scanlines, which affect the picture underneath). The RT4K uses mask images and tiles them across the screen to replicate the effect.

If you want to make your own CRT Mask, here's what you need to know:

• Custom CRT Masks must be saved as 32-bit .BMP files.
• The maximum dimensions of a CRT Mask image is 16 x 16 pixels. They can be smaller, which will result in denser tiling of the mask across the screen.
• A color value of 128 will be neutral,while 0 will completely black out the corresponding pixel. 255 will double the input value (although this will be clamped).
• Custom CRT Mask images should be stored in the "mask" folder on the SD card.

CRT masks will NOT adhere to the pixel grid like the RT4K's scanlines will. If you want them to adhere to the pixel grid, you'll need to have your shadow mask image match the dimensions of a single upscaled pixel, but this will vary depending on many factors, and so should be paired with a specific Profile you have in mind. Since Mask images have a maximum size of 16x16 pixels, this inherently means that the upscaled pixels of the input image cannot exceed 16x16 pixels in RT4K's output resolution.

Custom Color Matrix

RetroTINK-4K Custom Color Matrix Instructions - Custom color gamut correction factors can be loaded by the user. Each file is a set of csv values describing gamma and Input RGB -> XYZ transforms. The RT4K will automatically apply the correct XYZ -> Output RGB matrix depending on the specified HDMI output colorimetry.

The csv file has 14 entries (all floating point) on a single line:

• 1: Input Gamma
  
• 2: Input Lift
  
• 3: Input Gain
  
• 4: Output Gamma
  
• 5: Transfer Function (0 = sRGB, 1 = Rec. 601/709, 2 = SMPTE 240, 3 = Conventional Gamma)
  
• 6-14: Input RGB -> XYZ Matrix Coefficients

Thanks to Dan Mons, Keith Raney (https://github.com/danmons/colour_matrix_adaptations/tree/main) and Extrems (https://www.gc-forever.com/wiki/index.php?title=Game_Boy_Interface) for providing technical assistance and example data.

Coming Soon

• Custom Modelines
• Custom Input Modes
  

FAQ / Troubleshooting

Hardware Questions

Is there only 4K output? The RT4K supports any output up to 18Gbps, or 3840x2160p. You have common resolutions available on the remote, and more in the HDMI® Output menu.

Does the RT4K pass through 4k input? Is the input HDMI® 2.1? No. The maximum supported input is 1080p60.

What is the recommended power for the RT4K? Please use a power supply rated at 5v2A, or 10W, to power the RT4K.

Can I use my TV’s USB port for power? Most TV USB ports do not supply enough power for the RT4K. Please use a power supply rated at 5v2A, or 10W, to power the RT4K.

Does the RT4K use USB-C or Micro USB? The RT4K uses USB-C for power.

I see a lot of analog ports! Can any be used for output? The only port used for output is the HDMI® Out port. There are no plans to use the analog ports for output at this time.

Is the RT4K rack mountable? The case is not rack mountable. You may want to search for community members creating their own rack mount solutions.

Is there an S-Video or Composite port? If so, where are they? There is a discrete S-Video and Composite port in the front of the device, behind a sliding door. There are other ways to feed S-Video and Composite video to the RT4K; please check the Inputs section for more information.

The SCART port is loose! Can I get a return? All modern SCART input ports are sourced from the same factory, and they are all slightly loose and therefore “work as intended.” Please look into a SCART clamp with screws, similar to a VGA cable.

What kind of memory card should I use? The RT4K comes with an 8GB full-sized SD Card formatted in FAT32. The maximum size supported is 32GB.

Is there Wifi? No.

Is there Bluetooth? No.

Is there surround sound support? The RT4K passes through up to 8 channels LPCM via HDMI®, supports compressed surround sound through optical audio, and passes through DPLII as this is encoded in stereo.

What’s the VGA Pin Layout? Please see the Inputs section of the wiki.

What’s the SCART Pin Layout? Please see the Inputs section of the wiki

Is there ARC / eARC support? The RT4K should work in your ARC or eARC setup as long as it is not plugged into the ARC or eARC port on your TV.

Software Questions

Does resetting or updating the unit delete my profiles? Profiles and settings are stored in the SD Card. Barring a complete revamp of the way the RT4K works, your profiles should work between power cycles and updates if they’re saved on the SD Card. Settings do not stay set between power cycles, but you can set a profile to return to when you cycle power or make an update.

Can you run emulators on the FPGA? There are currently no plans to support emulators or cores on the RetroTINK-4K hardware itself.

Does the RT4K automatically switch resolution? The RT4K can detect changes in vertical resolution and switch to settings for each resolution. These are: 240p, 480i, 360p (GBI), 480p, 720p, 1080i, 1080p, and one additional custom resolution.

For 240p, 288p, 480i and 576i sources, the RT4K has an experimental feature to automatically detect changes in horizontal resolution. Please see the Sample Rate Detection section of the wiki for more information.

Does the RT4K automatically switch to a detected source? No. You will have to select your input manually.

Why isn't there automatic source switching? Per Mike Chi, "Auto switching is very difficult because you can’t easily tell the difference between YPbPr and RGsB. Also composite and s-video luma look pretty similar in a lot of ways to YPbPr."

Is there serial communication support through USB? The hardware is capable, but there is currently no support to communicate through the USB port.

Is there RS232 communication support through the VGA Port? The hardware is capable, but there is currently no support to communicate through the VGA port.

Does the RT4K support Game-ID? There is currently no way to communicate information to the RT4K.

Does the RT4K support [240p, 480i, 540p,786p, 1080i, 1536p] output? Does it support my HDCRT? The RT4K can support most progressive outputs that do not cross the 18Gbps threshold. If your output is not available in the HDMI® Output section, please create a custom modeline file for that output.

At this time, the RT4K does not support interlaced outputs such as 480i or 1080i.

Compatibility with your HD-CRT depends on whether they like any of the supported outputs of the RT4K and take HDMI®.

Can the RT4K record to the SDCard? The RT4K is not a recording device and will not save screenshots or video footage to the SD Card. Please consider buying a capture card for this purpose.

Support Questions

My 4K blinks yellow and then turns off! You may have replaced the .rbf file on your memory card. The .rbf file on your SD Card must match the firmware you are currently running. Please download any matching update .bin file and rbf (they should always be together) and do an update of your firmware by holding the reset button on the back and then powering the unit on using the remote.

The output is too sharp! It’s too blocky! If you feel the output is too sharp, try the following steps in this order

1. Make your way into the Image Processing menu (press SFX on the remote) and try changing the scaling algorithm to suit your preferences.
2. Try activating scanlines in the Image Processing menu and see which suits your needs
3. As a last-ditch effort, open the HDMI® Out menu (press OUT on the remote) and try a lower compatible resolution, and let your TV scale for you.

The picture is too bright with HDR on! HDR is for use with Black Frame Insertion, or Scanlines and CRT Masks. if you do not intend to use these, we suggest you turn the HDR setting off.

The picture is too dark with scanlines! If you do not have HDR turned on, try that first. If you have Black Frame Insertion on, try turning that off. If neither option helps, then your TV may not have the sheer brightness to brute force enough brightness through the CRT effects.

This is way too complicated, is there an "easy mode"? We suggest looking at the Getting Started section in the wiki, but we also suggest you look into using Profiles for your use case. We hope using Profiles becomes intuitive for getting your desired picture to your display.

Does this work with the RT5X remote? No. Both RT5X remotes are incompatible with the RT4K, and vice-versa.

I get picture from my RT4K but not my console?!? If you do get output from the RT4K but no input from your console, try the following:

1. Make sure your input is correctly selected in the RT4K input menu
2. Make sure your cable is correctly inserted into its appropriate jack as well as the console.
3. Check to see if your console is turned on.
4. Try to make sure, if your console has settings, that the appropriate output is selected
   • If you are playing on a PS2, make sure you select YPbPr or RGB in the BIOS menu
   • If you're playing on a console with both HDMI and AV output, you are using output consistent with how you want to connect it to the RT4K
5. If you are using a cartridge based console, like the N64, please take a monent to clean the contacts with 90%+ Isopropyl Alcohol and correctly insert the cartridge into the console.

My tink won't turn on/it lights up yellow and then turns off This may be due to a firmware mismatch. Please download the newest firmware and make sure both the update file and the firmware file are on your SD card, then hold the reset button and turn the RT4K on.

Compatibility Questions

Does the RT4K support Elgato? I heard RetroTINK doesn’t support Elgato. Older Elgato capture cards (typically the HD60 S and older) did not support older RetroTINK devices, such as the RT2X. As long as you feed the capture card a compatible resolution and leave the RT4K in triple buffer mode for maximum compatibility, Elgato capture cards will handle the its output just fine. Note that accurate capture (NOT passthrough) of CRT and LCD effects depends on your capture card's chroma subsampling rate, regardless of its brand, and as a result, most USB capture devices will not provide accurate capture of CRT and LCD effects at 4K.

It doesn’t work with my 1080p capture card! The RetroTINK-4K outputs 4K by default. Try outputting 1080p or lower to see if there is a resolution constraint for your capture card.

Is there HDCP Support? The RT4K will activate an effect that will obscure video when it detects HDCP is active in your input signal. The RT4K itself does not circumvent HDCP.

Can I use GCVideo Lite cables with my RT4K? The cables do output a signal, but there are other concerns regarding these cables.

Is the RT4K worth it for consoles from the 8th generation (PS4 / Xbox One) and beyond? You may want to look into using the RT4K on a modern console for the following reasons:

• Sharply scaling a console's 1080p output to 4K.
• Adding black frame insertion to decrease motion blur.
• Applying custom post processing effects for retro games on emulators.
• Trying out post processing effects on modern games made with a retro style using built-in pre-scaling features.

Can I use the RT4K to scale my set top box? If the output is not HDCP encrypted, you should be able to use the RT4K to upscale the image. Be advised: the RT4K is designed to sharply scale the image to another resolution, so you may prefer your display’s scaling to the way the RT4K does it.

You may also want to implement some image processing to allow you to give a more retro look to your content.

Can I upscale VHS/DVD? Yes, there are settings made specifically for deinterlacing content from VHS and DVDs.

Is the RT4K compatible with MiSTer DV? If you use direct video with your MiSTer you can use the HDMI® input directly into the RT4K.

Store/Pricing Questions

I want to buy two RT4K’s / How many can I buy? There is currently a limit of 1 per person for purchasing an RT4K unit.

Is the RT4K really $1,000? The RT4K currently retails for $750 directly from the RetroTINK store.

This is so expensive! The RT5X, RT2X, and RT2XSCART are still actively sold and supported, and will remain the flagship product for Mike Chi for the time being. Please look into those products for your upscaling needs.

Is there a coupon code for the RT4K? No, there are none and there are currently no plans to have one any time soon at the RetroTINK store.

When can I expect a price drop/sale? Black Friday? The Big Game? None of the RetroTINK products have ever gone down in price or gone on sale at the RetroTINK store. Unless there is a major change in the sourcing for the materials used, do not expect a cheaper price.

Is there a payment plan available? RetroTINK.com does not currently have any payment plans.

Can I buy a used RT4K? RetroTINK.com does not sell used or refurbished RT4K units.

I live in the UK and want a RT4K! Please use the special UK checkout link to purchase a unit directly from the RetroTINK store.

8bitmods and GamesConnection currently only carry older RetroTINK Products, but there are plans to sell the RT4K in early 2024.

I don't live in the USA! How can I buy a RT4K?? There are currently no international retailers for the RetroTINK-4K. The following stores do sell older RetroTINK products and will stock the RetroTINK-4K in early 2024.

International Resellers

Store	Country
RetroStuff	Canada
DragonBox Shop	Germany
GamesConnection	UK
8bitMods	UK
Consoles4You	Switzerland

I’d like to sell my RT5X to buy an RT4K! While that is your prerogative, if this is because you feel the RetroTINK-5X is obsolete, please know the RT5X is not at end of its life, and will be sold and supported for the foreseeable future.

Comparison Questions

My display does nearest neighbor upscaling, why would I need this? The RT4K gives you the flexibility to upscale any resolution to most other resolutions up to 4K in any method you prefer, with sub-frame latency. If your TV does nearest neighbor scaling with 720p then you are very much an outlier.

How does this compare to a CRT? CRTs have zero latency, whereas the RT4K will have sub-frame latency plus the latency of your display. While it is fast and near-zero, it is not zero like a CRT.

The RT4K does not support light guns the same way a CRT does.

A CRT is limited to its slot mask design, while the RT4K allows you to customize your slot masks and scanline effects by simply creating a custom image file.

How does this compare to the mClassic? The mClassic only outputs 1080p60, 1440p60 (if that's the native resolution of your display) or 4K30, while the RT4K can output up to 4K60.

The RT4K has a number of sharp and soft scaling algorithms that can be used to adjust the image to your liking.

How does this compare to the 4K Gamer Pro? The 4K Gamer Pro only processes 1080p signals and output them at 4K (other signals are simply passed through), while the RT4K can input and output almost any resolution.

Is this better than emulation? If you use well-shielded premium cables and video sources, the RT4K can be indistinguishable from emulation as long as you render the emulator at the same resolution as the source. The RT4K cannot help with how games render their graphics, so you may not get the expected results from early 3D consoles.

This doesn’t make my game look any better than on my TV Video game scalers do not change the internal rendering resolution of your console, which results in a very sharp upscale of a very low resolution picture. Premium scalers are made to lower input latency and add compatibility for older consoles.

Will this scale HDMI faster than my TV? There is some processing done to HDMI inputs, which will be shown in the Scaling/Cropping menu. This means this will add a small, almost miniscule, amount of latency to your game on top of your display.

Recommendation Questions

What's the best Capture Card to use with the RT4K? We recommend the AVerMedia Live Gamer 4K GC573 for an internal capture card, as it allows for full RGB 4:4:4 capture at 4K60.

What's the best Best HDMI® Splitter to use with the RT4K? For input, any HDMI® 1.4 10Gbps splitter is suitable. For Output, any HDMI® 2.0 18Gbps splitter is also suitable. As long as it doesn’t process the image there should be no additional latency.

What's the best best HDMI® Switch to use with the RT4K? Any HDMI® 1.4 switch rated at up to 10Gbps is suitable for the input. any HDMI®I 2.0 switch rated at up to 18Gbps is suitable for the output. As long as it doesn’t process the image there should be no additional latency.

What's the best HDMI® Cable to use with the RT4K? Please use any certified HDMI® 2.0 cable rated at 18Gbps.

Miscellaneous Questions

I want to use a scaler into the HDMI® input port of the RT4K While this may seem like a good idea, doubling up on scalers is not recommended (including the RetroTINK-5X!). Doubling up on scalers may result in undesirable scaling or suboptimal sampling.

The RT4K supports inputs up to 1080p60 so it may work, but the ADC on the RT4K may be better than your current scaler.

I want to use the mClassic on the RT4K input! While it is not recommended, the RT4K will accept HDMI® input up to 1080p60, which is the typical output of the mClassic.

I want to mClassic the output! While it is not recommended, please note the RT4K outputs 4K by default, while the mClassic only accepts up to 1080p as an input. You may need to change the RT4K’s output resolution to make it compatible.

I want to use 4K Gamer Pro on the RT4K output. This is unnecessary, as the RT4K already outputs 4K and allows for sharp scaling.

I lost the remote! Please purchase a new remote at the RetroTINK store.

Can I enable HDR on my input? This is possible, but your color mapping will not have any of the intended effects. The unit will work but you will see undesired colors. You should consider turning off HDR at your source and turning on HDR in the output menu.

If HDR from your console is important to you, consider using it directly to your display.

I lost my USB Cable! The included USB-C is actually not special in any way. You don’t even need data. As long as the cable can charge, you can use any USB-C cable with the RT4K.

Something is wrong with my unit! Please visit the RetroTINK Discord and ask for help in the RetroTINK-4K Help & Support Channel. You should be able to get help from somebody who may have had a similar problem previously.

I've checked the Discord channel and they were unable to help me / There is definitely something wrong with my unit after extensive testing! If you purchased your RetroTINK-4K at the RetroTINK store, please reply to your order confirmation email.

If you bought the unit from a partner store, please contact their support channels to see how they may help you.

RetroTINK-4K GUI Map

The GUI Map lists every single menu and menu item on the RetroTINK-4K, along with a brief description of what it does. For more information on them, click on a header to be taken to the appropriate section on this page.

GUI - Basic Setup

GUI - Input Selection

More information concerning inputs can be found in the Inputs section.

HDMI®
HDMI®	Selects the HDMI® In input.

Front
Composite	Selects the front composite input.
S-Video	Selects the front s-video input.

Rear RCA
YPbPr	Selects the rear RCA YPbPr input.
RGsB	Selects the rear RCA RGsB input.
CVBS on Green	Selects the rear RCA CVBS input.

SCART
RGBS (75 ohm)	Selects the SCART input and sets it to RGBS
RGsB	Selects the SCART input and sets it to RGsB
YPbPr	Selects the SCART input and sets it to YPbPr
CVBS on Pin 20	Enables Composite input on SCART Pin 20
CVBS on Green	Enables Composite input on SCART Green
Y/C on Pin 20/Red	Enables S-Video input on pin 20 and pin Red

HD-15
RGBHV	Enables RGBHV input on HD-15
RGBS	Enables RGBs input on HD-15
RGsB	Enables RGBsB input on HD-15
YPbPr	Enables Component input on HD-15
CVBS on Hsync	Enables Composite input on Hsync Pin
CVBS on Green	Enables Composite input on Green Pin
Y/C on Green/Red	Enables S-Video Input on Green/Red

GUI - HDMI® Output

More information concerning outputs can be found in the Outputs section.

Transmitter
HDR	Enables "HDR10 [8-bit]"
Colorimetry	Lets you choose between "Auto", "Rec. 709", "Rec. 2020", "Adobe RGB" and "Display-P3". With HDR enabled, Rec. 2100 is also available via the "Auto" setting.
Sync Lock	Lets you choose between "Triple Buffer", "Gen 50.0 Hz (x1)" and "Frame 50.0 Hz (x1)".
VRR	Lets you choose between "Off" and "FreeSync".
Deep Color	Lets you choose between "Off" and "On". Exceeds the HDMI® 2.1 bandwidth spec if used with 4K60 output.

Output Resolution
4K60	Sets the output to 3840x2160p at 60 frames per second
4K50	Sets the output to 3840x2160p at 50 frames per second
1080p60	Sets the output to 1920x1080p at 60 frames per second
1080p50	Sets the output to 1920x1080p at 50 frames per second
1080p100	Sets the output to 1920x1080p at 100 frames per second
1440p100	Sets the output to 2560x1440p at 100 frames per second
1080p120	Sets the output to 1920x1080p at 120 frames per second
1440p120	Sets the output to 2560x1440p at 120 frames per second
480p60	Sets the output to 640x480p at 60 frames per second

BFI Control
Strobe	Sets BFI Strobe.
Blur	Sets BFI Blur.
LCD Saver	Sets LCD Saver.

GUI - Profiles

Load Profile
Load From File	Loads a chosen profile from the "profile" folder on the SD card.
Load Default	Loads the Default Profile.

Save Profile
Save Current	Saves the current profile by overwriting the original file on the SD card.
Save As New	Saves the current profile as "New Profile #".

Assign Profile
Button 1	Sets a specified profile on the SD card to Button 1 on the remote.
Button 2	Sets a specified profile on the SD card to Button 2 on the remote.
Button 3	Sets a specified profile on the SD card to Button 3 on the remote.
Button 4	Sets a specified profile on the SD card to Button 4 on the remote.
Button 5	Sets a specified profile on the SD card to Button 5 on the remote.
Button 6	Sets a specified profile on the SD card to Button 6 on the remote.
Button 7	Sets a specified profile on the SD card to Button 7 on the remote.
Button 8	Sets a specified profile on the SD card to Button 8 on the remote.
Button 9	Sets a specified profile on the SD card to Button 9 on the remote.
Button 10	Sets a specified profile on the SD card to Button 10 on the remote.
Button 11	Sets a specified profile on the SD card to Button 11 on the remote.
Button 12	Sets a specified profile on the SD card to Button 12 on the remote.
Power Up	Sets a specified profile on the SD card to load when the RT4K is powered up.

GUI - Advanced Settings

GUI - Scaling/Cropping

Input Crop
Top Trim	Adjusts trim on the top edge of the picture.
Bottom Trim	Adjusts trim on the bottom edge of the picture.
Left Trim	Adjusts trim on the left edge of the picture.
Right Trim	Adjusts trim on the right sedge of the picture.
Vert. Pre-Scale	Reduces the effective vertical resolution of an HDMI® image. Can be set between "1/2" and "1/31".
RoTATE (Beta)	Enables image rotation methods.

CP Auto Crop
Vertical Only	Crops only the top and bottom edges of the image, sets Aspect Correction to "4:3 (PAR)" and Scaling Mode to "Proportional".
Full Crop to 4:3	Crops all edges of the image, sets Aspect Correction to "4:3 (PAR)" and Scaling Mode to "Proportional".
Full Crop to 16:9	Crops all edges of the image, sets Aspect Correction to "16:9 (PAR)" and Scaling Mode to "Proportional".

Scaler
Aspect Correction	Lets you choose between "4:3 (PAR)", "16:9 (PAR)" and "1:1 (Sq. Pixel)" options.
Scaling Mode	Lets you choose between "Auto Fill", "Proportional", "Free-Form" and "Auto Fill Integer" options.
Vert. Factor	Adjusts the vertical height of the image. Only available when Scaling Mode is set to "Proportional" or "Free-Form".
Hori. Factor	Adjusts the Horizontal width of the image. Only available when Scaling Mode is set to "Free-Form".

Buffer
Length	Displays the current lag in milliseconds. Can be set to "Min. Lag", "1/2 Frame" or "1 Frame".

Masking Color
Red	Adds red to the cropping mask, between 0 and 31.
Green	Adds green to the cropping mask, between 0 and 31.
Blue	Adds blue to the cropping mask, between 0 and 31.
Show	Lets you choose between "Cropping Only" and "Always".

GUI - Processing / Effects

Interpolation
Vert. Kernel	Lets you choose between "Bilinear Sharp", "Bilinear Med.", "Bilinear Std.", "Bilinear Soft", "Cubic", "Lanczos2", "Lanczos3", "Sinc", and "None".
Hori. Kernel	Lets you choose between "Bilinear Sharp", "Bilinear Med.", "Bilinear Std.", "Bilinear Soft", "Cubic", "Lanczos2", "Lanczos3", "Sinc", and "None".
Anti-Ringing	Can be set to "On" or "Off". Only visible on "Lanczos2" and "Lanczos 3".

Scanline
Function	Lets you choose between "Off", "Exponential", "Gaussian", "Super Gaussian", "Linear", "Box", "LCD Mono" and "LCD RGB". Anything except for "Off" will enable the settings below.
Strength	Increases scanline strength from 0 to 99.
Modulation	Increases modulation strength from 0 to 99.
Red Bleed	Enables red bleed.
Red Convergence	Adjusts red convergence from -10 to 10.
Blue Convergence	Adjusts blue convergence from -10 to 10.

Mask
Enable	Enables the Mask feature, as well as the Strength option. Will not appear to do anything until "Load from File" is used.
Strength	Adjusts the mask strength from -10 to 10.
Load from File	Select a Mask File from the "mask" folder on the SD card.

Horizontal Blur
Function	Lets you choose between "Off" and "IIR LPF", enabling the Cut-Off Freq option below.
Cut-Off Freq	Adjusts the blur strength from 0.50 MHz to 9.00 MHz, in 0.25 increments.

GUI - Color Correction

Gamma/PQ
Input Factor	Factor used to convert the input from gamma space to linear light. Can be adjusted between 0.1 and 5.00.
Input Lift	Lift adds an offset to the input gamma conversion. Can be adjusted between -1.00 and 1.00.
Input Gain	Gain multiplies the output of the input gamma conversion. Can be adjusted between 0.00 and 10.00.
Output Factor	Factor used to convert encode the output of the video pipeline back to gamma space. Can be adjusted between 0.10 and 5.00.
SMPTE 2048 PQ	For HDR output mode, the RT4K uses a perceptual quantizer instead of simple gamma. The control sets the maximum brightness of the PQ in units of nits. Can be adjusted from 250 to 10,000.

Color Space Conversion
Apply Preset	Lets you load a CSC file from the "csc" folder on the SD card. The csc file is a list of presets to quickly apply gamma and conversion matrix.
Custom Matrix	Enables the Input RGB to XYZ conversion matrix.
Prevent Clipping	Automatically scale the CSC matrix so that highlights are not lost at the cost of making the image dimmer. Can be set to On or Off.
Saturation	Controls the color intensity. Lowering it turns the image black and white. Raising it makes the colors more intense. Can be set from -1.0 to +1.0.

Input RGB to XYZ
Xo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Xo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Xo[Bin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Bin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Bin]	Can be adjusted between -1.75000 to +1.75000.

Advanced Controls
Bit Crush	Lowers the color depth of the picture. Can be adjusted between "Off" and "7 bits Removed". This is useful to eliminate rounding errors in GBI or to create an artificially lower bit depth effect (similar to posterize in Photoshop).
Saturation	Increases or decreases image color saturation. can be adjusted between -1.00 and +1.00.
Transfer Function	Can be set to "sRGB 0.055", "Rec.601/709 0.099", "SMPTE 240M 0.1115" or "Gamma". The various transfer functions linearize the low-end of the gamma curve to avoid bit loss. "Gamma" uses a simple gamma encoding.

GUI - Black Frame Insertion

BFI Control
Strobe	Strobe sets the number of times a frame is flashed in the BFI.
Blur	Blur sets the duration of each flash in the BFI.
LCD Saver	IPS LCD displays may exhibit temporary image retention due to the flashing BFI pattern. LCD saver alternates the phase of the BFI flash to reduce this effect. However you will see a momentary glitch on every inversion.

BFI Color
Blending Mode	Sets the BFI insertion mode: Black/grey frame, Colored frame, blend to black or blend to color.
Red	Adjusts Red, Green and Blue from 0 to 31.
Green	Adjusts Red, Green and Blue from 0 to 31.
Blue	Adjusts Red, Green and Blue from 0 to 31.

GUI - Deinterlacer / Film

Mode
Algorithm	Lets you choose between "Motion Adaptive", "Weave", "Bob", "Linear", "Blend", "CRT Simulation" and "LCD Blending".
Field Inversion	Reverses the fields of 480i signals. Can be set to "Off" or "On".

Motion Adaptive Settings
Sensitivity	Adjusts the sensitivity of the Motion Adaptive Deinterlacer. Can be set to "Low", "Medium", "High" and "Max". Higher settings result in a more solid image but with more weaving artifacts.
Noise Threshold	Adjusts the noise threshold, at the cost of weaving. Can be adjusted between 0 and 63.
Interpolator	Choose which field to prioritize. Can be set to "Average", "Bottom Field" and "Upper Field"
Detector	Can be set to "Zero-lag" or "Symmetric".

Bob Settings
Offset	Adjusts how far each field is shifted when using the "Bob" Algorithm. Can be set between -3 and +3.

Film Mode
Inverse Telecine	Enables a detector for "3:2" telecine (24fps content) and "2:2" telecline (30fps content).
Dejudder 24 Hz	Can be set to "Off" or "On".

Cadence Detection
Motion Digital	Can be set from 0 to 500.
Motion CP	Can be set from 0 to 500.
Motion SDP	Can be set from 0 to 500.
Threshold	Can be set from 0 to 500.

GUI - Acquisition

GUI - HDMI® In Receiver

Input Decimation
Input Pixels	Can be set between "1 (Output: 1)" and "15 (Output: 1)".
Output Pixels	Can be set between 1 and 15.
Initial Phase	Can be set between "1 of X" and "X of X", where "X" what Input Pixels is set to.

Colorspace
4:2:2 Upsampler	Can be set to "Linear" or "Nearest".
Input Range	Can be set to "Auto", "RGB Lim.", "RGB Full", "YCbCr 601", "YCbCr 709", "XUYCC 601", "XUYCC 709", "YCbCR 601 (Full)" or "YCbCR 709 (Full)".

Misc.
A/DAC Mode	Can be set to "Off", "NTSC" or "PAL".

GUI - RGB / Component ADC

Sampling
Samples per Line	Manually set the sampling.
Decimation Factor	Can be set to between 2 and 16.
Decimation Phase	Value range matches the Decimation Factor.
Sub-Phase	Adjusts the Sub-Phase in 11.25 increments. Can be set as high as "348.75 deg"
Anti-Alias LPF	Can be set to "Auto (16MHz)", "9MHz (Strong)", "16 MHz (Med)", "35 MHz (Light)", "95 MHz (Min.)" and "Off".

Sync
SoG Threshold	Adjusts the Sync on Green Threshold in 11.29 increments. Can be set between "0.00 mV" and "327.42 mV".
Pre-coast	Can be set between 1 and 31.
Post-coast	Can be set between 1 and 31.
Slow-lock	Gives more time to lock onto Sync on Green. Can be set to "Off" or "On".

Gain
Pre-ADC	Adjusts the picture gain. Can be set between -0.7 and +0.8.
Red	Adds red to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.
Green	Adds green to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.
Blue	Adds blue to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.

Offset
Red	Can be set between -100 and +100.
Green	Can be set between -100 and +100.
Blue	Can be set between -100 and +100.

Auto Calibrate
Phase	Analyzes the picture to determine the Sub-Phase setting. Works best on detailed images with high contrast details.
Gain	Analyzes the picture to determine the Red, Green and Blue Phase settings. Works best on calibration screens like in the 240p Test Suite.

GUI - Sample Rate Detection

Control
Auto Dec. Factor	Can be set to "Off" or "On". Enables all other options in the Sample Rate Detection Menu
Auto Dec. Phase	Can be set to "Off" or "Auto".
ADC Sample Rate	Manually set the sampling.

Progressive Detection
Enable Sample Rate A	information
Enable Sample Rate B	information
Enable Sample Rate C	information
Enable Sample Rate D	information
Enable Sample Rate E	information
Enable Sample Rate F	information

Interlaced Detection
Enable Sample Rate A	information
Enable Sample Rate B	information
Enable Sample Rate C	information
Enable Sample Rate D	information
Enable Sample Rate E	information
Enable Sample Rate F	information

GUI - SDP Decoder

Gain / Balance
Brightness	information
Contrast	information
Chroma	information
Phase	information
Blue Only	information
Setup	information

Processing
Y/C Filter	information
Comb Bandwidth	information
Chroma Badwidth	information
Sharpness	information
CTIE	information

Sync
H-Lock Speed	information
Standard	information

GUI - Audio Input

Sampling
Sample Rate	Can be set to "48 kHz" or '96 kHz".
Pre-amp Gain	Can be set between "-24.0 dB" and "+28.0 dB" in 0.5 increments.

Source
Input Override	Manually changed the audio input to another source. Can be set to "Off", "RCA", "HD-15", "SCART", "Front" or "S/PDIF".
Input Swap	Can be set to "Mono (Left)", "Mono (Right" or "L/R Swap".

GUI - System

GUI - OSD / Firmware

On Screen Display
Position	Can be set to "Left", "Center" and "Right".
Auto-Off	Sets the time the menu will disable after inactivity. Can be set up to "100 sec" in 10 sec increments.
Load Banner	Loads a menu banner from the "image" folder on the SD card.
Enable Debug OSD	Permenantly displays one of the debug OSDs on the screen. Can be set to "Off", "Status Pg 1", "Status Pg 2", "Status Pg 3" or "Console".

Firmware Update
Check SD Card	Checks the SD card for update files stored in the SD card's root directory. If multiple firmware files are present, the most recent one will be chosen.

GUI - Device

GUI - Status

Status
Lets one display one of three System Status pages relating to the RT4K.

GUI - System Status Page 1

Video Source
Video Source	CP Proc. (I assume CP Proc will change based on selection)
Input Timing	information
Pixel Clock	information
Freq	information
Detected Mode	information

Audio Input
Audio Input	I2S (I assume will change based on audio input)
Measured Freq	information
Measured Freq	information
HDMI® N / CTS	information

FPGA Core
Scaler Clock	information
PLL VCO	information
Pipeline	information
SDRAM Clock	information
SDRAM Load	information

HDMI® Transmitter
Output Timing	information
Active Size	information
Pixel Clock	information
HDMI® Standard	information

PIC32MX MCU
System Clock	information
Uptime	information
Loop Time	information
Last IR Code	information
SD Card Free	information

GUI - System Status Page 2

HDMI® Input Protocol Analyzer
TMDS	information
Mode	information
Resolution	information
Colorspace	information
H. Timing	information
V. Timing (F0)	information
V. Timing (F1)	information
Audio	information
AVI Infoframe	information
Aud. Infoframe	information
VS Infoframe	information
ACP Infoframe	information

GUI - System Status Page 3

HDMI® TX Information
TX Mode	information
Hot Plug	information
Scrambling	information
Clock Factor	information
Ch 0 Error	information
Ch 1 Error	information
Ch 2 Error	information
Sink EDID Dump	information

GUI - Diagnostic Console

Diagnostic Console
Displays a diagnostic console screen regarding HDMI® In TX channels.

GUI - About

About
About	Displays the name of the device, the firmware version, and the Device ID.
Resources	Displays the URLs for the RetroTINK website, Discord channel, and the RetroTINK-4K wiki page.
Thanks!	Displays a thank you message from Mike Chi to the user.