N64:N64HDMI: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
(Created a page for the Aliexpress HISPEEDIDO N64HDMI mod kit, with instructions and details.)
 
No edit summary
Line 1: Line 1:
= HISPEEDIDO N64HDMI (HDMI) =
The [https://hispeedido.com/n64-hdmi HISPEEDIDO N64HDMI] video processor is an internal add-on to all retail Nintendo 64 game consoles.  
The [https://hispeedido.com/n64-hdmi HISPEEDIDO N64HDMI] video processor is an internal add-on to all retail Nintendo 64 game consoles.  


Line 13: Line 12:
* 8 color modes.
* 8 color modes.


=== <u>On-Screen Display Combination</u> ===
== <u>On-Screen Display Combination</u> ==
To activate the basic OSD, the button combination is '''START + A + B'''
To activate the basic OSD, the button combination is '''START + A + B'''


Line 21: Line 20:
|· Bend the Flex slightly below the resistor arrays,  and slightly after.
|· Bend the Flex slightly below the resistor arrays,  and slightly after.


* It should comfortably sit over the top of the DENC-NUS chip
# It should comfortably sit over the top of the DENC-NUS chip
# Align the flex on the RCP to pin 6.
# Tape it down with the thinnest Kapton tape (5 or 10mm)
# Solder the wires
# Solder the pins to the correct section
# The Controller extension can be trimmed
# The “T” QSP is unused.
# Solder the 5V flex to the transistor by looping it over.
# If you find that there are issues, the 5V flex may have become damaged. In that case, wire manually.
# Solder the following points, bending the wires  neatly:
#* Pin 2 – RC
#* Pin 16 – CON
#* Pin 27 – RST


· Align the flex on the RCP to pin 6.
== No-cut Version ==
 
The UltraHDMI NOCUT 3d print will work fine, but there is a remixed version of the base on [https://www.thingiverse.com/thing:6740462 Thingiverse by user VariablePwn] that suits the HISPEEDIDO kit more effectively.
· Tape it down with the thinnest Kapton tape (5 or 10mm)
 
· Solder the wires
|
|-
|· Solder the pins to the correct section
 
· The Controller extension can be trimmed
 
· The “T” QSP is unused.
 
· Solder the 5V flex to the transistor by looping it over.
 
* If you find that there are issues, the 5V flex may have become damaged. In that case, wire manually.
 
· Solder the following points, bending the wires  neatly:
 
* Pin 2 – RC
* Pin 16 – CON
* Pin 27 – RST
 
|
|}
 
== NO-CUT Version ==
The UltraHDMI NOCUT 3d print will work fine, but there is a remixed version of the base on [https://www.thingiverse.com/thing:6740462 Thingiverse by user VariablePwn]that suits the HISPEEDIDO kit more effectively.


You will still be required to download the shroud from the [https://www.thingiverse.com/thing:3254371 LaserBear (collingall) Thingiverse page].
You will still be required to download the shroud from the [https://www.thingiverse.com/thing:3254371 LaserBear (collingall) Thingiverse page].

Revision as of 23:35, 26 August 2024

The HISPEEDIDO N64HDMI video processor is an internal add-on to all retail Nintendo 64 game consoles.

It is currently one of the cheaper options available on AliExpress, and follows the same soldering process as many of the existing modification processes.

From the website, the kit states:

  • This N64-HDMI Mod kit is compatible with all N64 models/regions, with the exception of 'Pikachu' models.
  • This N64-HDMI kit is a digital to digital HDMI output upgraded for the Nintendo 64.
  • 720P HDMI-Compatible Output.
  • Built-in OSD Menu.
  • Built in 3 TV Aspect Ratio.
  • 8 color modes.

On-Screen Display Combination

To activate the basic OSD, the button combination is START + A + B

Installation instructions

Instructions can be found on the main website, but below is a short guide with additional information for a smoother installation process:

· Bend the Flex slightly below the resistor arrays, and slightly after.
  1. It should comfortably sit over the top of the DENC-NUS chip
  2. Align the flex on the RCP to pin 6.
  3. Tape it down with the thinnest Kapton tape (5 or 10mm)
  4. Solder the wires
  5. Solder the pins to the correct section
  6. The Controller extension can be trimmed
  7. The “T” QSP is unused.
  8. Solder the 5V flex to the transistor by looping it over.
  9. If you find that there are issues, the 5V flex may have become damaged. In that case, wire manually.
  10. Solder the following points, bending the wires neatly:
    • Pin 2 – RC
    • Pin 16 – CON
    • Pin 27 – RST

No-cut Version

The UltraHDMI NOCUT 3d print will work fine, but there is a remixed version of the base on Thingiverse by user VariablePwn that suits the HISPEEDIDO kit more effectively.

You will still be required to download the shroud from the LaserBear (collingall) Thingiverse page.

Retrieved from "https://consolemods.org/wiki/index.php?title=N64:N64HDMI&oldid=47182"