AV:RetroTINK-4K

From ConsoleMods Wiki
Jump to navigation Jump to search

Notes

Deinterlacer -> -> Motion Adaptive Settings -> Sensitivity


(medium and high options might be might be reversed) Controls combing effect at costs of sharpness. Low = less combing.


Deinterlacer -> -> Motion Adaptive Settings -> Interpolator:


Basically controls how the "bob" portion of the MA is calculated. The bob is either taken from the line above, line below or the average of the upper and lower lines BFI. It's a matter of preference. I think either Top or Bottom interpolator looks a little sharper. Average is softer In the end it doesn't matter too much because Bob is only used during motion when it is hard to see detail anwyays


Deinterlacer -> Motion Adaptive Settings -> Detector:


This is a little complicated to explain... but let me try basically symmetric adds one frame of lag but the motion detection may be better. Because it is looking "one field into the future" idk if its really better tho in real life


HDMI -> BFI Control


-Strobe: How much the frame is divided down (i.e. 1 = divide by 2, 2 = divide by 3, 3 = divide by 4) from input to output -Blur: How many frames are ON vs OFF. So let's say we are converting 60 Hz -> 240 Hz. Blur = 1, ON, OFF, OFF, OFF. Blur = 2 is ON, ON, OFF, OFF -LCD Saver - inverts the pattern of the BFI to avoid renetion. But every few minutes u will see a flicker

Custom Mode Lines


  1. RT4K Custom Mode Line Format
  2. H active, H front porch, H sync, H total blank, polarity (1 = pos, 0 = neg)
  3. V active, V front porch, V sync, V total blank, polarity (1 = pos, 0 = neg)
  4. Nominal frame rate (floating point)
  5. Text name

RetroTINK-4K GUI Map

Basic Setup

Input Selection

Front
Composite information
S-Video information
RCA
YPbPr information
RGsB information
CVBS on Green information
SCART
RGBS (75 ohm) information
RGsB information
YPbPr information
CVBS on Pin 20 information
CBVS on Green information
Y/C on Pin 20/Red information
HD-15
RGBHV information
RGBS information
RGsB information
YPbPr information
CBVS on Hsync information
CBVS on Green information
Y/C on Green/Red information
HDMI
thing a information
thing b information

HDMI Output

Transmitter
Deep Color information
HDR information
Sync Lock information
Vrr information
BFI Control
Strobe information
Blur information
LCD Saver information
Output Resolution
4K60 information
4K50 information
1080p60 information
1080p50 information
1080p100 information
1440p100 information
1080p120 information
1440p120 information
480p60 information

Scaling/Cropping

Input Crop
Left Trim information
Right Trim information
Top Trim information
Bottom Trim information
Vert. Pre-Scale information
Scaler
Aspect Correction information
Scaling Mode information
Vert. Factor information
Hori. Factor information
Interpolation
Vert. Kernel information
Hori. Kernel information
Buffer
Length information

Image Processing

Scanline
Function information
Strength information
Modulation information
Red Bleed information
Red Convergence information
Blue Convergence information
Mask
Enable information
Strength information
Load from File Select a Mask File, RGB Masks:, Mono Masks:
Horizontal Blur
Function information
Boost information
Gamma/Linear Light/HDR
Input Factor information
Output Factor information
SMPTE 2048 PQ information

Deinterlacer

Mode
Algorithm: information
Field Inversion: information
Motion Adaptive Settings
Sensitivity information
Interpolator information
Detector information
Bob Settings
Offset information

System

On Screen Display
Position information
Auto-Off information
Load Banner information
Enable Debug OSD information
Blanking Color:
Red information
Green information
Blue information
Firmware Update
Check SD Card information

Advanced Setup:

RGB/Component ADC

Sampling
Sampling Rate information
Decimation Factor information
Decimation Phase information
Sub-Phase information
Anti-Alias information
Sync
SoG Threshold information
Pre-coast information
Post-coast information
Gain
Pre-ADC information
Red information
Green information
Blue information
Auto Calibrate
Phase information
Gain information

HDMI Receiver

Receiver
Decimation Factor information
Decimation Phase information
Color Space
4:2:2 Upsampler information
CSC Mode: information
Input RGB Range information

SDP Decoder

Gain/Balance
Brightness information
Contrast information
Chroma information
Phase information
Blue Only information
Setup information
Processing
Y/C Filter information
Comb Bandwidth information
Chroma Bandwidth information
Sharpness information
CTIE information
Sync
H-Lock Speed information
Standard information

Audio Input

Sampling
Sampling Rate information
Pre-amp Gain information
Source
Input Override information
Input Swap information

Profiles

Load Profile
Load Default information
Load From File (opens file selector window titled "Select Profile")
Save Profile
Save Current information
Save As New information
Assign Profile
Button 1 information
Button 2 information
Button 3 information
Button 4 information
Button 5 information
Button 6 information
Button 7 information
Button 8 information
Button 9 information
Button 10 information
Button 11 information
Button 12 information
Power Up information

Device

Status

System Status Page 1:

Video Source
Video Source CP Proc. (I assume CP Proc will change based on selection)
Input Timing information
Pixel Clock information
Freq information
Detected Mode information
Audio Input
Audio Input I2S (I assume will change based on audio input)
Measured Freq information
Measured Freq information
HDMI N / CTS information
FPGA Core
Scaler Clock information
PLL VCO information
Pipeline information
SDRAM Clock information
SDRAM Load information
HDMI Transmitter
Output Timing information
Active Size information
Pixel Clock information
HDMI Standard information
PIC32MX MCU
System Clock information
Uptime information
Loop Time information
Last IR Code information
SD Card Free information

System Status Page 2:

to do

System Status Page 3:

to do

Diagnostic Console

to do

About

About
Device: information
FW Version information
Device ID: information