Xbox 360:Error Codes
Do not ever put your console in the freezer or out in the cold/hot weather or wrap it in a towel. These "fixes" will cause bigger problems due to temperature shock, board warping, and condensation. |
This page is intended to be a comprehensive list of all error codes for all models of Xbox 360, as well as tutorials on fixing them if applicable/possible. This error code guide is in no way official and may not be 100% accurate as it is community sourced. We take no responsibility for any actions you may take to fix your console.
Generally, if there is a problem with the Xbox 360, the LEDs in the Ring of Light (ROL) around the power button will flash in a particular pattern. The pattern itself lends some insight to the problem. Certain patterns will also display numbered error codes on screen, known as your primary error code, which will further help diagnose your console’s issue.
No Power
Board is unresponsive to power button
Red Ring of Death
Ring of light quadrants flashing red/center light red
- To diagnose, hold down the sync button and press eject 4 times
- Each time you press eject, a certain number of the quadrants of the ring will flash
- 4 lights signify 0
- 1 lights signify 1
- 2 lights signify 2
- 3 lights signify 3
- On Xbox 360 E consoles, the ring will flash an amount of times then pause, count these to get the numbers
- After pressing it 4 times, you will have the secondary error code
- Example: seeing 4 lights 3 times, followed by 1 light once, means you have error code: 0001
System Management Controller (SMC) Errors
Error Code | Name | Explanation | Possible Repair Actions |
---|---|---|---|
0001 | ERROR_V_12P0 | ANA_V12P0_PWRGD negated unexpectedly | Replace Power Supply, Check V_12P0 rail components |
0002 | ERROR_V_CPUCORE | VREG_CPU_PWRGD negated unexpectedly | Replace Power Supply, Check V_CPUCORE rail components |
0003 Phat |
ERROR_V_GPUCORE | VREG_GPU_PWRGD negated unexpectedly | Replace Power Supply, Check V_GPUCORE rail components |
0003 Slim |
ERROR_V_3P3 | VREG_V3P3_PWRGD negated unexpectedly | Replace Power Supply, Check V_3P3 rail components |
0010 | ERROR_NO_HANA/ERROR_NO_ANA | HANA/ANA is not responding to reads or writes | Replace HANA/ANA or Southbridge |
0011 | ERROR_THERMAL_CPU | CPU temperature overload | Detailed Diagnostic/Repair Actions |
0012 | ERROR_THERMAL_GPU | GPU temperature overload | Detailed Diagnostic/Repair Actions |
0013 | ERROR_THERMAL_EDRAM | eDRAM temperature overload | Detailed Diagnostic/Repair Actions |
0020 | ERROR_GPU_RST_DONE | GPU_RST_DONE signal missing after seqUnReset time passed | Detailed Diagnostic/Repair Actions |
0021 | ERROR_NO_PCIE | PCIE link did not enter L0 after seqUnReset time passed | Detailed Diagnostic/Repair Actions |
0022 | ERROR_NO_HANDSHAKE | CPU did not send GetPowerUpCause to SMC | Detailed Diagnostic/Repair Actions |
0023 Phat |
ERROR_NO_CLOCKCHIP | Clockgen is not responding to reads or writes | Replace ANA_BCKUP (Xenon), ANA/HANA, or Southbridge |
0023 Slim |
ERROR_V_CPUEDRAM | VREG_VEDRAM_PWRGD negated unexpectedly | Replace Power Supply, Check V_CPUEDRAM rail components |
0030 | ERROR_NO_TEMPERATURES | HANA/ANA temperature registers read as zero | Check for shorted resistors, replace HANA/ANA |
0031 | ERROR_V_5P0 | VREG_V5P0_PWRGD negated unexpectedly | Replace Power Supply, Check V_5P0 rail components |
0032 | ERROR_V_CPUVCS | VREG_CPUCORE_VCS_PWRGD negated unexpectedly | Replace Power Supply, Check V_CPUVCS rail components |
0033 | ERROR_V_MEM | VREG_VMEM_PWRGD negated unexpectedly | Replace Power Supply, Check V_MEM rail components |
Xbox System Software (XSS) Errors
Error Code | Name | Explanation | Possible Repair Actions |
---|---|---|---|
0100 E 16 |
ERROR_NBINIT_MEM_VENDOR_ID | RAM Vendor ID wrong, or not detected | Replace GPU or RAM |
0101 E 17 |
ERROR_NBINIT_MEM_READ_STROBE_DATA_WRITE | Could not write data for RAM read strobe training | Replace GPU or RAM |
0102 E 18 |
ERROR_NBINIT_MEM_READ_STROBE_DELAY_TRAINING | Memory read strobe delay training failed | Replace GPU or RAM |
0103 E 19 |
ERROR_NBINIT_MEM_WRITE_STROBE_DELAY_TRAINING | Memory write strobe delay training failed | Replace GPU or RAM |
0110 E 20 |
ERROR_MEMORY_ADDRESSING | Memory address line failed or unresponsive | Replace GPU or RAM |
0111 E 21 |
ERROR_MEMORY_DATA | Memory data line failed or unresponsive | Replace GPU or RAM |
0300 E 48 |
ERROR_MFG_COMM_FAILURE | Unknown | Unknown |
0301 E 49 |
ERROR_MFG_UNABLE_TO_CONNECT | Unknown | Unknown |
0302 E 50 |
ERROR_MFG_CONNECTX_FAILURE | Unknown | Unknown |
0303 E 51 |
ERROR_MFG_GATEWAY_ERROR | Unknown | Unknown |
0310 E 52 |
ERROR_MFG_BAD_RESPONSE_DATA | Unknown | Unknown |
0311 E 53 |
ERROR_MFG_CHALLENGE_REFUSED | Unknown | Unknown |
0312 E 54 |
ERROR_MFG_BAD_VAULT | Unknown | Unknown |
0313 | ERROR_XSS_MANUF_TEST | Manually triggered error code | Unknown |
1000 E 64 |
ERROR_XSS_CDROM_TIMED_OUT | Kernel DVD drive communications timed out | Replace SATA cable to DVD drive, replace DVD drive PCB, replace Southbridge |
1001 E 65 |
ERROR_XSS_CDROM_NOT_DMA_CONFIGURED | Kernel could not configure DVD drive for DMA mode | Replace SATA cable to DVD drive, replace DVD drive PCB, replace Southbridge |
1002 E 66 |
ERROR_XSS_CDROM_COULD_NOT_CREATE_DEVICE | Kernel could not create DVD drive instance | Replace SATA cable to DVD drive, replace DVD drive PCB, replace Southbridge |
1003 E 67 |
ERROR_XSS_HDD_TIMED_OUT | Kernel HDD communications timed out | Replace HDD, replace HDD port/cable, replace Southbridge |
1010 E 68 |
ERROR_XSS_HDD_NOT_DMA_CONFIGURED | Kernel could not configure HDD for DMA mode | Replace HDD, replace HDD port/cable, replace Southbridge |
1011 E 69 |
ERROR_XSS_HDD_COULD_NOT_CREATE_DEVICE | Kernel could not create HDD instance | Replace HDD, replace HDD port/cable, replace Southbridge |
1012 E 70 |
ERROR_XSS_HDD_NOT_FOUND | Kernel couldn't find HDD Note: This error does not show up because a HDD is missing, it shows up when a HDD is detected, but can't be found | Replace HDD, replace HDD port/cable, replace Southbridge |
1013 E 71 |
ERROR_XSS_XAM_NO_DASH | XAM could not find dash.xex on flash | Unplug HDD, if error clears, format or replace HDD, else Rebuild and reflash NAND |
1020 E 72 |
ERROR_SMC_FLASH_CONFIG_CORRUPT | SMC configuration corrupt | Rebuild and reflash NAND |
1021 E 73 |
ERROR_HSIO_TRAINING_FAILED | GPU to eDRAM High Speed Link failed, eDRAM faulty or unresponsive | Replace GPU |
1022 E 74 |
ERROR_HSIO_CALIBRATION_FAILED | GPU to eDRAM High Speed Link failed, eDRAM faulty or unresponsive | Replace GPU |
1023 E 75 |
ERROR_UNEXPECTED_ETHERNET_PHY_VENDOR | Southbridge could not communicate with Ethernet PHY over MDIO/MDC | Replace Ethernet chip, replace Southbridge |
1030 E 76 |
ERROR_ETHERNET_PHY_RESET_FAIL | Ethernet PHY failed to reset correctly or complete reset | Replace Ethernet chip |
1031 E 77 |
ERROR_ETHERNET_PHY_READ_WRITE_FAIL | Could not read or write to Ethernet PHY | Replace Ethernet chip |
1032 E 78 |
ERROR_UNSUPPORTED_GPU | GPU is down revision, not supported on this board | Replace GPU with correct revision for board |
1033 E 79 |
ERROR_XSS_FLASH_NO_XAM | xam.xex not found on flash | Unplug HDD, if error clears, format or replace HDD, else Rebuild and reflash NAND |
1100 E 80 |
Unknown | Unknown | Unknown |
1101 E 81 |
Unknown | XeKeysSecuritySaveSettings failed | Replace NAND |
1102 E 82 |
ERROR_HSIO_CALIBRATION_FAILED | CGPU to eDRAM High Speed Link failed, eDRAM faulty or unresponsive | Replace CGPU |
References
- Octal's Error Database on the Repair Wiki (from leaked documentation and reverse engineering)