RetroTINK-4K GUI Map
Basic Setup
Input Selection
| Front
|
| Composite
|
information
|
| S-Video
|
information
|
| RCA
|
| YPbPr
|
information
|
| RGsB
|
information
|
| CVBS on Green
|
information
|
| SCART
|
| RGBS (75 ohm)
|
information
|
| RGsB
|
information
|
| YPbPr
|
information
|
| CVBS on Pin 20
|
information
|
| CBVS on Green
|
information
|
| Y/C on Pin 20/Red
|
information
|
| HD-15
|
| RGBHV
|
information
|
| RGBS
|
information
|
| RGsB
|
information
|
| YPbPr
|
information
|
| CBVS on Hsync
|
information
|
| CBVS on Green
|
information
|
| Y/C on Green/Red
|
information
|
| HDMI
|
| thing a
|
information
|
| thing b
|
information
|
HDMI Output:
Scaling/Cropping
| Input Crop
|
| Left Trim
|
information
|
| Right Trim
|
information
|
| Top Trim
|
information
|
| Bottom Trim
|
information
|
| Vert. Pre-Scale
|
information
|
| Scaler
|
| Aspect Correction
|
information
|
| Scaling Mode
|
information
|
| Vert. Factor
|
information
|
| Hori. Factor
|
information
|
| Interpolation
|
| Vert. Kernel
|
information
|
| Hori. Kernel
|
information
|
| Buffer
|
| Length
|
information
|
Image Processing
| Scanline
|
| Function
|
information
|
| Strength
|
information
|
| Modulation
|
information
|
| Red Bleed
|
information
|
| Red Convergence
|
information
|
| Blue Convergence
|
information
|
| Mask
|
| Enable
|
information
|
| Strength
|
information
|
| Load from File
|
Select a Mask File, RGB Masks:, Mono Masks:
|
| Horizontal Blur
|
| Function
|
information
|
| Boost
|
information
|
| Gamma/Linear Light/HDR
|
| Input Factor
|
information
|
| Output Factor
|
information
|
| SMPTE 2048 PQ
|
information
|
Deinterlacer
| Mode
|
| Algorithm:
|
information
|
| Field Inversion:
|
information
|
| Motion Adaptive Settings
|
| Sensitivity
|
information
|
| Interpolator
|
information
|
| Detector
|
information
|
| Bob Settings
|
| Offset
|
information
|
System:
(System Setup)
On Screen Display:
Position:
Auto-Off:
Load Banner:
Enable Debug OSD:
Blanking Color:
Red:
Green:
Blue:
Firmware Update:
Check SD Card
Advanced Setup:
RGB/Component ADC
(RGB/Component ADC Setup)
Sampling Rate:
Decimation Factor:
Decimation Phase:
Sub-Phase:
Anti-Alias:
Sync:
SoG Threshold:
Pre-coast:
Post-coast:
Gain:
Pre-ADC:
Red:
Green:
Blue:
Auto Calibrate:
Phase:
Gain:
HDMI Receiver
Reciever
Decimation Factor:
Decimation Phase:
Color Space:
4:2:2 Upsampler:
CSC Mode:
Input RGB Range:
SDP Decoder
(SDP Decoder Setup)
Gain/Balance
Brightness:
Contrast:
Chroma:
Phase:
Blue Only:
Setup:
Processing:
Y/C Filter:
Comb Bandwidth:
Chroma Bandwidth:
Sharpness:
CTIE:
Sync:
H-Lock Speed:
Standard:
Audio Input
(Audio Setup)
Sampling
Sampling Rate:
Pre-amp Gain:
Source
Input Override:
Input Swap:
Profiles:
(Profiles)
Load Profile:
Load Default
Load From File
(opens file selector window titled "Select Profile")
Save Profile:
Save Current
Save As New
Assign Profile:
Button 1:
Button 2:
Button 3:
Button 4:
Button 5:
Button 6:
Button 7:
Button 8:
Button 9:
Button 10:
Button 11:
Button 12:
Power Up:
Device:
Status
System Status Page 1:
Video Source: CP Proc. (I assume CP Proc will change based on selection)
Input Timing:
Pixel Clock:
Freq:
Detected Mode:
Audio Input: I2S (I assume will change based on audio input)
Measured Freq:
HDMI SR:
HDMI N / CTS:
FPGA Core
Scaler Clock:
PLL VCO:
Pipeline:
SDRAM Clock:
SDRAM Load:
HDMI Transmitter
Output Timing:
Active Size:
Pixel Clock:
HDMI Standard:
PIC32MX MCU
System Clock:
Uptime:
Loop Time:
Last IR Code:
SD Card Free:
System Status Page 2:
System Status Page 3:
Diagnostic Console
About
Device:
FW Version
Device ID: