AV:RetroTINK-4K

sharplThe RetroTINK-4K is an advanced video scaler from RetroTINK LLC. Building on the functionality of the RetroTINK-2X and RetroTINK-5X, the RetroTINK-4K offers high-end video scaling and processing at resolutions up to 4K60.

It is commonly abbreviated as "TINK-4K" or "RT4K".

The RetroTINK-4K, alongside the included remote and SD card.

Overview

The RetroTINK-4K is the latest evolution of the RetroTINK line of video line doublers and upscalers. Below is a list of some standout features:

Output

• Digital Video up to 4K60
  • Flexible output modes including 480p, 1080p, 1440p at various refresh rates
  • Custom modelines on the SD card
• Fully buffered video (drop-free on input changes), Gen Locked and Frame Locked sync modes
• HDR10 output with full color correction to Rec. 2020
• High frame rate output modes: 1440p120, 1080p240
• Optional deep color output (10 bits at 4K60 may not be compatible with all displays)
• Up to 8-ch LPCM audio

Inputs

• Supports for virtually all analog formats:
  • HD15/VGA: RGBHV, RGBS, RGsB, YPbPr, S-video and Composite
  • SCART: RGBS, RGsB, YPbPr, S-video and Composite
  • Rear RCA: RGsB, YPbPr and Composite
  • Front Composite
  • Front S-Video
• Digital Video Input supporting up to 1080p60/1200p (CVT-rb)
• Analog audio input sampled at up to 96kHz/24-bit with full gain control
• Optical TOSLINK audio input supporting 2-Ch LPCM or compressed surround
• Digital Video audio supports up to 8-ch LPCM

Analog Video

• Automatic gain calibration
• Automatic phase calibration
• Automatic input cropping to trim borders
• Full control of gain, offset and sample rate
• Console specific automatic sample rate detection (experimental feature)
• Support for a wide variety of off-spec arcade and PC boards (may require custom profiles to properly trim and center the image)
• Max input resolution of 1920x1080p60 or 1920x1200p60 CVT-rb
• Robust composite/S-video decoder with multi-region support (NTSC, PAL, PAL-60, SECAM)

Scaling

• Fully flexible, custom cropping and zooming in the horizontal and vertical space independent of other settings
• Automatic aspect ratio correction to 4:3 or 16:9
• Motion adaptive deinterlacing including film modes for 3:2 and 2:2 inverse telecine (experimental feature)
• RoTATE 90 deg CW or CCW (for 240p, 288p and 360p inputs)

CRT Simulation

• Multiple CRT beam profiles

• Fully configurable CRT beam strength and intensity modulation
• Adjustable CRT masks and strength
• Interlaced video simulation with offset scanlines
• LCD simulation patterns that automatically adapt to scaling, including non-integer factors

Image Processing

• End to end RGB pipeline with internal 12-bit precision
• Conventional gamma and approximated modes to minimize quantization error
• Advanced and fully configurable gamma and perceptual quantizer (HDR)
• Advanced color gamut transforms to simulate different display technologies
• Black frame insertion engine with customizable pattern and intensity
• Linear light processing

User Interface

• Advanced OSD menu based system
• SD Card for saving profiles, custom modelines and firmware updates
• Support for over 100,000 profiles
• Custom premium remote control

Getting Started

Insert SD card with RT4K firmware, HDMI™ output, USB-C power and whatever inputs you wish to use.

The RetroTINK-4K is designed to be powerful, yet easy to use and quick to set up. Here are some steps to get started Using the RetroTINK-4K:

1. SD Card - A card is included with every RetroTINK-4K that includes the launch firmware and profiles. Please make sure this card is inserted in the device, as it is required for proper operation. If you lose the card, any FAT32 SD card 32 GB or less may be substituted.
2. USB-C Power - Connect a USB-C cable supplying at least 5V/2A to the USB-C power input on the 4K.
3. Video Output - Connect an HDMI™ cable (2.0 or higher / 18Gbps+) from the RetroTINK-4K output to your display.
4. Video Input - Connect your device's signal to any of the RetroTINK-4K's inputs. More information on supported connections can be found in the Inputs section.
5. Confirm Video Output - By default, the RetroTINK-4K outputs 4K60. If you don't see any picture, confirm that your display supports 4K60, or press the button on the remote that matches the resolution of your display (1080p, 1440p, or 480p). See the Remote and Output sections for more information.
6. Select Your Input Source - Press the "Input" button at the top of the remote, then choose the port and signal your device is using.
7. Enjoy - Once your video source is visible, that is it! Enjoy the high quality, low latency scaling of the RetroTINK-4K. Time to play the game!

Basic Analog Calibration

With your game up and running, you may want to consider two more steps if you're using an analog video source (note that HDMI™ video sources do not require calibration):

Auto Calibrate the Gain: The RetroTINK-4K has a function to automatically calibrate the gain, which works well so long as there's a patch of pure white somewhere on the screen. Gain should be applied on a per-console basis. To quickly use Auto Gain, press the "Gain" button on the remote. Advanced users may want to use the manual gain controls under Advanced Settings > RGB/Component ADC, in tandem with the 240p Test Suite.

Crop The Picture: Cropping the picture is how the RetroTINK-4K scales images to the edges of a screen and centers them, and should be applied on a per-game basis. For best results, use a screen that has no black or dark edges. There are three ways to automatically crop the picture, which can be accessed via the AUX buttons at the bottom of the remote: AUX1 - "Vertical Only", cropping only the top and bottom edges. AUX2 - "Full Crop to 4:3", cropping all four edges. AUX3 - "Full Crop to 16:9", cropping all four edges and setting the Aspect Correction to 16:9. You can also manually crop and resize the picture if you wish by going to Advanced Controls > Scaling/Cropping. Head to that section to learn more.

Tweaks, Filters and Beyond

Of course, there is a lot more you can do with the RetroTINK-4K. Here are some more advanced options to explore:

• Update the Firmware
• Choose an Expert-Crafted Optimal Profile
• CRT and Scanline Effects
• Improve Image Vividness with HDR
• Improve Motion Clarity With Black Frame Insertion

Firmware Updates

The RetroTINK-4K can be updated to any firmware, with new firmware releases adding more new features as they are made.

1. Power off your RetroTINK-4K and remove the SD card.
2. Insert the SD card used for your RT4K into the SD card slot on your computer.
3. Download the latest firmware .zip file from the RetroTINK website.
4. Extract the contents of the .zip file to the SD card's root directory.
5. Remove the SD card and insert it into the SD card slot on the RetroTINK-4K.
6. There are two methods for initiating the installation of a new firmware. If you have multiple firmware files on the SD card, the RT4K will always pick the most recent one.
   • Option 1: Power on the RetroTINK-4K, then go to Advanced Settings > OSD/Firmware. In the Firmware update section, select "Check SD Card" to scan for the firmware file, then confirm that you want to install it.
   • Option 2: Hold down the blue Reset button on the back of the RetroTINK-4K, then power it on. The firmware installation will begin automatically.
   • If the LED blinks red, an install error has occurred. Check the files on the SD card and try again.
7. The RT4K will reboot for about 40 seconds, with the front LED flashing pink and then blue. Once done, it will power on again as normal with a green LED. You're done!

All custom profiles, CSC files, banner images, input modes, mask overlays and modelines will be kept, as those are stored on the SD card instead of on the RT4K itself.

Remote

RetroTINK-4K Remote Diagram
	Button	Description	Button	Description	Button	Description
	Power	Powers on / off the TINK-4K	11	Profile 11	4K	Switches to 3840x2160p 60Hz
	INPUT	Input source selection menu	12	Profile 12	1080p	Switches to 1920x1080p 60Hz
	OUT	Digital Video Output menu	MENU	RetroTINK-4K Main Menu	1440p	Switches to 2560x1440p 60Hz
	SCL	Scaling/Cropping menu	BACK	Back out to previous menu	480p	Switches to 720x480p 60Hz
	SFX	Processing/Effects menu	△	Up	RES1	Custom Output Resolution 1
	ADC	HDMI™ Receiver menu if Digital In is currently displayed RGB/Component ADC menu if an analog input is currently displayed	◁	Left	RES2	Custom Output Resolution 2
	PROF	Profiles menu	ENTER	Enter	RES3	Custom Output Resolution 3
	1	Profile 1	▷	Right	RES4	Custom Output Resolution 4
	2	Profile 2	▽	Down	AUX1	"Vertical Only" Auto Crop
	3	Profile 3	DIAG	Diagnostic Console screen	AUX2	"Full Crop to 4:3" Auto Crop
	4	Profile 4	STAT	Status screen	AUX3	"Full Crop to 16:9" Auto Crop
	5	Profile 5	AUTO-GAIN	Auto Calibrate Gain	AUX4
	6	Profile 6	AUTO-PHASE	Auto Calibrate Phase	AUX5
	7	Profile 7	PLAY/PAUSE	Pause current screen	AUX6
	8	Profile 8	SAFE	Safe Mode	AUX7
	9	Profile 9	SYNC-GEN	Sync Lock - Gen Lock	AUX8
	10	Profile 10	SYNC-BUF	Sync Lock - Triple Buffer	-

Pause Button

The Remote features one function that cannot be accessed anywhere else: the Pause function. Pressing this will pause the on the current frame and mute the audio. This frame will even be remembered if you switch to a different input source and back.

• Perhaps the most useful application of the Pause Button is the Deinterlacer/Film menu. Here you'll be able to adjust the deinterlacing settings and see their effects more easily in a scene in motion, letting you tweak them to your liking more easily.

There are a few situations where using the Pause function will have undesirable results, such as loading a different profile or engaging 3:2 Inverse Telecine. Other functions, such as Black Frame Insertion, won't be visible at all because they require new video frames in order to work. In these cases, simply unpause to resume normal operation.

Safe Mode

Safe Mode is an option accessible by pressing the blue Reset button on the back of the unit, or by holding down the "SAFE" button on the remote for two seconds. This causes the following:

• Loads the Default profile.
• Sets the input to Digital In.
• Sets the output to 480p at 59.94 Hz.

Safe Mode is intended for use in troubleshooting, as any display that supports HDMI should be required to support 480p60. It's also handy as a fall-back in case you need to return the RetroTINK-4K to a default state for any reason.

LED Light

The RetroTINK-4K has a front LED light that changes color and behavior to convey information about its operation to the user. Below is a chart for LED light behavior and what they mean.

Color	Description
No light	The RT4K has no power. No electrons, no business.
Slow Red pulse	The RT4K is sleeping, and must be turned on for use.
White	The RT4K is booting up, but is not yet ready for use.
Green	The RT4K is on and ready for operation.
Yellow flash	System files not found on SD card during boot. Check to see if the SD card is correctly inserted, that it has the .rbf system file, and that the rt4k.bin file matches it.
Purple-Purple flash	The RT4K is updating the firmware.
Blue-Blue flash	Firmware update is successful.
Red flash	Firmware update error. Check the files on the SD card and try again (the unit is NOT bricked).

Inputs

The RetroTINK-4K features inputs for a wide variety of signals and connector types, which can be selected in the Input Source Selection menu. These options can be accessed by pressing the Input button at the top of the remote, or by pressing the Menu button and choosing "Input Selection".

Digital Video

Digital Video Input

The RetroTINK-4K supports many resolutions digitally, up to 1920x1080p60 or 1920x1200p60 CVT-rb. It does NOT support higher resolution input, including 1440p and 4K input. Unlike standard consumer equipment, the RetroTINK-4K can tolerate and adapt to arbitrary and off-spec resolutions.

Front

The RetroTINK-4K offers S-Video (over Mini-DIN) and Composite (over RCA) inputs in the front (which can be concealed / revealed by moving the sliding panel). The red and white RCA jacks are stereo audio inputs. Red/White front audio inputs are active when either the Front Composite or S-Video input is selected (assuming audio input override is not used).

Front Inputs
	Composite	To use composite video, use the yellow RCA jack for video (CVBS/Composite) and the Red/White RCA jacks for right and left audio input, respectively.
	S-Video	To use composite video, use the Mini-Din for video (Y/C S-Video) and the Red/White RCA jacks for right and left audio input, respectively.

Rear RCA

The rear RCA jacks support YPbPr (Component), RGsB, and CVBS (Composite) inputs.

Rear RCA Input
	YPbPr	The Rear RCA input supports YPbPr (Component video). The maximum resolution supported is 1920x1080p at 60fps, or 148.5Mhz. To use YPbPr, connect the Red, Green and Blue YPbPr video cables to their corresponding colored RCA connectors, noting that the Red/White pair to the left is for stereo audio input.
	RGsB	The Rear RCA input also supports RGsB (aka RGB Sync on Green), a flavor of RGB that sends the sync alongside the Green signal. The maximum resolution supported is 1920x1080p 60fps, or 148.5Mhz To use RGsB, connect the Red, Green and Blue RGsB signals to their corresponding colored RCA connectors, noting that the Red/White pair to the left is for stereo audio input.
	CVBS on Green	Composite video (CVBS) can be used with the Rear RCA inputs. The maximum supported resolution is 480i. To use CVBS on Green, connect the yellow composite signal connector to the Green RCA jack, then setting the input to "CVBS on Green" option in the Input Selection menu. The Red/White pair of jacks furthest left is for stereo audio input.

SCART

The SCART port is the large rectangular input on the right-hand side of the device. SCART has many different options for video input using the same connector design, as it was designed to carry a wide array of them using a single cable.

• Two M4x0.7 thread screw-holes sit on either side of the SCART port, 70.4mm apart from each other relative to their centers. These allow for a user-made solution to give a more secure fit for the SCART cable (similar to the HD-15 port's screw-holes).

SCART Input
	RGBS (75 ohm)	RGBS is a form of RGB where sync is sent through a discrete line. The RetroTINK-4K accepts the following RGBS signal formats via SCART: Composite Sync (attenuated), Sync-on-Luma, and Sync-on-composite. They all work by sending information down the Red, Green, Blue, and "Sync" lines. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	RGsB	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via SCART. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	YPbPr	YPbPr is sent through the Green, Blue, and Red pins, respectively. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	CVBS on Pin 20	Composite video sent through Pin 20, usually through a composite to SCART adapter or if your cable uses sync-on-composite video and you wish to use composite instead of RGB. As with all composite signals, only 240p/480i/288p/576p signals are supported.
	CBVS on Green	Composite video can be sent through the Green pin. This would be useful if you use a component (YPbPr) to SCART adapter, just plug composite (yellow) into the Y RCA jack (Green). As with all composite signals, only 240p/480i/288p/576p signals are supported.
	Y/C on Pin 20/Red	S-Video (Y/C) can be sent down Pin 20 (sync) and the Red pins. You will need a S-Video to SCART adapter. As with all S-video signals, only 240p/480i/288p/576p signals are supported.

SCART Jack Pinout
	Pin #	RGBS (75 Ohm)	RGsB	YPbPr	CVBS on Pin 20	CBVS on Green	Y/C on Pin 20/Red
	1	Unused
	2	Audio In - Right
	3	Unused
	4	Ground
	5	Ground
	6	Audio In - Left
	7	Blue	Blue	Pb
	8	Unused
	9	Ground
	10	Unused
	11	Green	Green+Sync	Y		CVBS
	12	Unused
	13	Ground
	14	Unused
	15	Red	Red	Pr			Chroma (C)
	16	Unused
	17	Ground
	18	Ground
	19	Unused
	20	Sync			CVBS		Luma (Y)

HD-15

The HD-15 connector (or VGA connector) is commonly associated with PCs, however it's also famously available for the SEGA Dreamcast.

• Unlike SCART, the HD-15 port does not accept audio. When using HD-15, audio should be input using the RT4K's 3.5mm TRS input (associated with the HD-15 port by default) or the TOSLINK "optical" input.

HD-15 Input
	RGBHV	RGBHV is a form of RGB where information is sent through 5 lines: Red, Green, Blue, Horizontal Sync, and Vertical Sync. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz. This is most common for PC sources.
	RGBS	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via SCART. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	RGsB	RGsB sends sync down the green input, using only 3 cables. This RGB format is notably used by the PS2 when in 480p mode via SCART. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	YPbPr	YPbPr is sent through the Green, Blue, and Red pins, respectively. The maximum resolution supported is 1920x1080p 60fps, or 148.5 MHz
	CBVS on Hsync	Composite video sent through the horizontal sync line. As with all composite signals, only 240p/480i/288p/576p signals are supported.
	CBVS on Green	Composite video can be sent through the Green line. As with all composite signals, only 240p/480i/288p/576p signals are supported.
	Y/C on Green/Red	S-Video (Y/C) can be send down Green (Y) and the Red (C) pins. As with all S-video signals, only 240p/480i/288p/576p signals are supported.

HD-15 Jack Pinout
	Pin #	RGBHV	RGBS	RGsB	YPbPr	CBVS on Hsync	CBVS on Green	Y/C on Green/Red	Data
	1	Red	Red	Red	Pr			Chroma(C)
	2	Green	Green	Green+Sync	Y		CVBS	Luma(Y)
	3	Blue	Blue	Blue	Pb
	4	Unused
	5	Ground
	6	Ground
	7	Ground
	8	Ground
	9	Unused
	10	Ground
	11	Unused
	12								External Transmit (EXT TX)
	13	Horizontal Sync	Sync			CVBS
	14	Vertical Sync
	15								External Receive (EXT RX)

3.5mm TRS Audio

3.5mm TRS Audio

The RetroTINK-4K allows for audio through a 3.5mm TRS input. This accepts stereo analog audio. By default, this is associated with the HD-15 port, as that port does not accept audio signals.

Optical Audio

Optical Audio

The RetroTINK-4K offers a discrete optical audio TOSLINK input. This input can accept 2-channel LPCM and compressed surround sound.

Alternate Audio Inputs

The RetroTINK-4K allows you to reassign audio inputs from their default video source. Go to Advanced Settings, and select "Audio Input" under the "Acquisition" section. The "Input Override" option under "Source" allows the audio for the current input video input to be taken from a different audio source. The only exception is that it is not possible to assign HDMI (TM) audio to a non-HDMI (TM) video source. The reverse, however, is possible.

• This menu also has the Input Swap option, letting you swap the audio input channels (handy for some third-party Saturn cables), or derive mono audio using the left or right channels (useful for single-channel systems like the NES).

Audio Input Override Sources

Picture	Name	Description
	RCA (Rear)	The leftmost two RCA inputs in the rear. White and Red,
	HD15	The 3.5mm TRS input in the rear.
	SCART	The SCART input on the side. Audio is fed in through pins 2 and 6.
	Front	The red and white RCA inputs in the front of the unit.
	SPDIF	Optical audio fed through a Toslink input.

HDMI™ Output

The RetroTINK-4K only outputs via the Digital Video output port. Note that The RetroTINK-4K can not output through any of its analog ports.

The HDMI™ Output menu allows you to set your output resolution, enable black frame insertion, change your colorspace output (colorimetry), and more. Here is a breakdown of some key functions:

Output Resolutions

The following outputs are readily supported by the RetroTINK-4K. Also noted are resolutions available by pushing their respective button on the remote. If you are unsure which resolution to use, use the buttons on the remote.

RetroTINK-4K Output Resolutions

Resolution	Description	Remote Button?
4K60	Default resolution and framerate for 4k displays, aka 3840x2160p. Default Resolution for the RT4K	Yes
4K50	Intended for PAL games and 24Hz content.	No
1080p60	Default resolution for 1080p displays.	Yes
1080p50	Intended for PAL games. and 24Hz content	No
1440p60	Default resolution and framerate for 1440p monitors, aka 2560x1440p.	Yes
1440p50	Intended for PAL games and 24Hz content	No
1080p100	Intended for PAL games and 24Hz content with BFI	No
1440p100	Intended for PAL games and 24Hz content with BFI	No
1080p120	Intended for NTSC content with BFI	No
1440p120	Intended for NTSC content with BFI	No
480p60	Minimum suggested output resolution for modern displays, aka 720x480p. Pressing the Reset button on the back of the unit activates this resolution.	Yes
2880x2160p70.00	Intended for off spec content from retro computers	No
1920x2160p60.00		No
800x600p60.00	Output for retro computers.	No
1920x1200p60	5x output for consoles intended for 8:5 (16:10) displays.	No

HDR

HDR is a way for the RetroTINK-4K to output a much more luminous picture for TVs that support it. HDR is intended for use with either Black Frame Insertion or Scanlines and Masks, as it helps compensate for the darkened image.

• Currently, the only option available is "HDR10 [8-bit]".

The table below shows two photos of an LG-CX displaying the RT4K using the "PVM 600 TVL" profile, under the HDR CRT Simulation folder. It's impossible to communicate the luminance of HDR in SDR, so here the camera had its exposure set for the HDR photo first, demonstrating the luminance gain compared to the SDR photo.

HDR Comparisons - Off-screen Photos
PVM 600 TVL scanlines - SDR.	PVM 600 TVL scanlines - HDR.

Colorimetry

HDMI Output Colorimetry specifies the colorspace of the HDMI output. By default, the Auto setting will select Rec. 709, and toggle to Rec. 2100 when HDR is enabled. You may wish to manually set output to Rec. 2020 (without HDR enabled), Adobe RGB or DCI-P3 if your display supports a wider color gamut. This may improve the image quality/accuracy when using the settings in the Color Correction menu.

Sync Lock

Older video game consoles didn't always have perfect video timings. CRTs typically had no problems working with these variances, but these "imprecise" consoles can sometimes have trouble working with modern TVs and capture devices that conform to a more rigid standard. Some games, such as Silent Hill or Chrono Cross on the PlayStation 1, will alternate between 240p or 480i video modes if you are in-game or in the items/pause menu, respectively. On many displays, upscalers and capture devices, this will create a long delay and a "no input detected" screen for several seconds while the device reorients to the new video mode. The issue of a device taking a gameplay-harming amount of time to change between video modes has been colloquially called the "Chrono Cross" problem.

Sync Lock controls how the RetroTINK-4K synchronizes the output frame rate with the input frame rate and handles these input changes.

• Triple Buffer operates the output independently from the input which results in a stable output signal even if the input signal glitches or changes. However, this comes at the cost of a variable lag, usually between a fraction of a frame to a fraction of a frame plus one whole frame. On occasion, you will see judder when frames needed to be dropped or repeated.
• Gen Lock is the recommended mode as long as your display is compatible with the source's refresh rate. Gen Lock loosely couples the output frame rate with the input frame rate. After a few seconds, the output frame rate will lock with the input frame rate and achieve minimum lag without screen judder.
• Frame Lock tightly couples the input and output frame rates. Any change in the input frame rate will cause a disruption in the output signal and a hard resynchronization.

Variable Refresh Rate (VRR)

The RetroTINK-4K can flag the output as VRR. While the RetroTINK-4K itself never outputs variable frame rates, settings this flag may be useful to force the display to accept a broader range of refresh rates. It is also useful on some displays to prevent re-buffering and other frame rate changes which will interfere with the RetroTINK-4K's BFI generator.

Deep Color

Explain Deep Color here.

BFI Control

Gives you quick access to the Strobe and Blur functions of Black Frame Insertion. For more BFI controls, head to the "Black Frame Insertion" (BFI) section.

Profiles

The Profiles section handles all of the profiles provided on the SD card, as well as any you've put there yourself. Profiles allow you to save your settings to load later. This is where you'll find CRT presets, since they're just saved profiles.

• For a list of Profiles provided on the SD card by default, head to the Profile Repository section.
• For a collection of Profiles made by the community not provided on the SD card by default, head to the Community Profiles section.

Load Profile

• Load From File - Selecting this will bring up a menu where you can navigate through the "profiles" folder on the SD card to load up a specific profile.
• Load Default - Loads the Default Profile. The Default Profile can never be deleted or overwritten.

The arrangement of profiles in the Load From File menu matches the internal file structure of the "profiles" folder on the SD card. This means that you can alter the folder structure to your liking if you don't prefer how they're laid out by default.

Save Profile

• Save Current - Overwrites the currently-loaded profile with the current settings. If selected while using the Default Profile, this will work like "Save As New" instead.
• Save As New - Saves the current profile as a new file named "New Profile X", where X is an ascending number. This will be located in the root "profiles" folder on the SD card, and can be renamed using a PC.

Assign Profile

This section of the menu allows you to assign one of the number buttons at the top of the remote to a specific profile, using the same SD card navigation menu as the "Load From File" function.

Additionally, this is where you can assign a profile to be loaded up when the RetroTINK-4K is Powered Up. This is not the Default Profile, which can never be changed.

Scaling and Cropping

The Scaling / Crop Setup menu is where you can crop and resize the image. Unlike the RetroTINK-5X, by default the RT4K sizes and positions the image based on the cropping, but this can be overridden.

Input Crop

The RetroTINK-4K has robust controls to adjust size, positioning and cropping:

• "Top Trim" and "Bottom Trim" will effectively scale the image up and down in most Scaling Modes.
  • To more easily see the edges of the Top and Bottom Trims, set the Scaling Mode to "Auto Fill Integer".
• "Left Trim" and "Right Trim" will adjust the centering of the image, as the RT4K automatically centers the image based on these settings.
  • To shift the image left and right, increase the Left or Right trim to push the image in the opposite direction.

Vertical Pre-Scale

The RetroTINK-4K features the ability to "Pre-Scale" video content, or discard scanlines, at a fractional increment of the source input. Discarding vertical lines results in a loss of vertical resolution. This loss can be useful under certain circumstances, such as creating more accurate scanline rendering for 240p visual content output from consoles that run at higher resolutions (such as the Dreamcast or Wii).

RoTATE

RoTATE (pronounced "roh-tah-tay") is a special feature within the RetroTINK-4K to rotate the image 90 degrees clockwise (right) or counterclockwise (left). This is especially useful for games that may only display their image horizontally, such as many arcade shooters.

RoTATE Example
Standard Output	90 Degrees Right	90 Degrees Left

The RoTATE mode will only work if the samples per line of your video source is lower than 1024 samples per line (visible in the RGB/Component ADC menu).

• Because the video of Composite and S-Video is locked to 858 samples per line, no additional tweaking is required when using these input sources.
• Further, RoTATE mode will only work with 240p, 288p or 360p resolutions. This is important for titles that mix them with 480i.

If you're using RGB or YPbPr input, visit the RGB/Component ADC (link) section of this page for information on ADC and decimation settings to meet the 1024 samples per line requirement. Similar limits apply when using HDMI™ sources: use the Input Decimation settings in the "HDMI™ Receiver" menu if the horizontal samples exceed 1024 (for example, MiSTer cores that use pixel repetition).

CP Auto Crop

The RetroTINK-4K can automatically crop and set aspect ratio for an input if it is fed a sufficient game screen (although this only works with RGB and Component sources).

Autocrop looks for the black edges of a game image and crops to them, so use a picture that clearly shows the edges of the video for best results. Screens that have any dark edges, as well as letterboxed, pillar-boxed, and window-boxed screens, are not recommended as they will fool the Auto Crop into thinking those are the edges of the image, resulting in an incorrect crop.

CP Auto Crop Settings

Name	Remote Button	Effect
Vertical Only	AUX 1	Automatically adjusts "Top Trim" and "Bottom Trim" to the top and bottom of the game image. Does not adjust Left Trim or Right Trim, and does not change Aspect Correction.
Full Crop to 4:3	AUX 2	Automatically adjusts Left, Right, Top, and Bottom Trim to the image, and changes Aspect Correction to "4:3 (PAR)"
Full Crop to 16:9	AUX 3	Automatically adjusts Left, Right, Top, and Bottom Trim to the image, and changes Aspect Correction to "16:9 (PAR)"

Scaler

The Scaler section in the RetroTINK-4K allows you to manipulate the geometry of the image.

Aspect Correction

The Aspect Correction setting chooses the pixel aspect ratio, or "PAR", of the image. Options can be toggled between

• 4:3 (PAR) - uses the common 4:3 pixel aspect,
• 16:9 (PAR) - intended for games set to their widescreen or anamorphic display modes.
• 1:1 (Sq. Pixel) - displays the pixels as perfect squares. This is helpful for systems like Super Game Boy and PSP.

Note that some inputs, such as modern HDMI™ sources, use square pixels by definition, so no PAR adjustments are possible. You will have to use the Scaler settings below instead.

Scaling Mode

Scaling Mode allows you to select automatic scaling modes or change aspect ratio constraints on manual scaling:

• Auto Fill - fills the screen based on the selected Aspect Correction aspect ratio.
• Proportional - allows the Vertical Factor to be adjusted while automatically adjusting the Horizontal Factor to keep the aspect ratio selected in Aspect Correction.
• Free-Form - untethers the Vertical Factor and Horizontal Factor to allow values outside of the Aspect Correction setting. This is the setting most like the RetroTINK-5X's resizing options.
• Auto Fill Integer - scales the Vertical Factor and Horizontal Factor to the highest possible integer value without exceeding the screen boundaries while respecting the ratio selected in Aspect Correction.

The Horizontal Factor and Vertical Factor settings display the multiplier value, the input resolution, and output resolution respectively.

The function can be expressed as a simple formula: (Input Resolution) X (Multiplier) = (Output Resolution).

Horizontal and Vertical Factor Example
Axis	Multiplier	Input Res.	Output Res.
Vert. Factor	9.000	240	2160
Hori. Factor	2.045	1440	2945

Buffer

The RetroTINK-4K allows users to set how much video to buffer before outputting to your screen. The buffer, in conjunction with the Sync Lock mode, are the main determining factors for overall latency.

• Min. Lag sets the buffer to only store to bare minimum number of video lines. This option provides the lowest latency.
• 1/2 Frame always buffers half a frame.
• 1 Frame frame always buffers a full frame.

Min. Lag is typically compatible, but if you encounter an edge case with screen tearing, try forcing 1/2 or full frame.

Note that certain movie modes, such as Inverse Telecine, will automatically force the RetroTINK-4K to buffer a full frame.

Masking Color

The masking colour settings allow you to adjust the colour of the mask that displays in the Scaling/Crop menu. By default, the values a 0 Red, 0 Green and 31 Blue. You can also change whether the masking colour is displayed in the cropping menu only, or always.

Processing and Effects

The Processing / Effects Setup menu is where you can adjust the pixel interpolation, as well as add Scanlines and CRT Masks.

Where are the Scanline Presets?

If you're a regular user of the RetroTINK-5X, you may be surprised to enter this menu and find that there's no Presets available to choose from. This is because they are stored as Profiles on the SD card.

• To load an included CRT Preset, head to the main menu, then go Profiles > Load from File > HDR CRT Simulation, then pick one you want to use.

The "bundling" of CRT Presets as Profiles may seem odd to users of the RetroTINK-5X (where CRT Presets could easily be applied to optimal sampling profiles), however this shouldn't have much impact on the final result. CRT displays are inherently a bit blurry as part of their aesthetic (even PVMs and BVMs), so generic sampling is perfectly acceptable to use for them. If you're using a digital source and decimating it (like Nintendo Switch Online or an HDMI modded system), you may want to simulate the blur using the Horizontal Interpolation Kernel, and / or the Horizontal Blur function.

The only exception to the above is when you're using the LCD scanlines, as the thin lines dividing each pixel won't appear correctly without optimal sampling.

Interpolation

Vertical and Horizontal Kernel

Interpolation in relation to video processing is a technique to create more visual information on the output that is given on the input. These processes help make a more visually cohesive image, and reduce effects such as shimmering when the image is scrolling. The RetroTINK-4K offers a handful of interpolation options that can be applied independently across the vertical and horizontal axis.

• Bilinear Sharp: The image is scaled up the maximum integer factor that is within the output size using Nearest Neighbor followed by a bilinear scale to the final output size. This option provides sharp pixels without shimmer at non-integer scaling factors.
• Bilinear Medium: The image is scaled up 2x using Nearest Neighbor followed by a bilinear scale to the final output size. This option is somewhat softer than Bilinear Sharp but still sharper than regular Bilinear.
• Bilinear Std: The image is scaled using conventional bilinear filtering.
• Bilinear Soft: This performs linear interpolation over 4 pixels instead of the standard 2 pixels resulting in a very soft image. This may be desirable to produce horizontal blur for CRT effects
• Cubic: Interpolation using the bicubic spline kernel which outputs an image sharper than bilinear but softer than Lanczos.
• Lanczos2 and Lanczos3: Interpolation using the Lanczos family of scaling algorithms. Lanczos is a popular algorithm that provides good results for natural imagery (i.e. movies) and most 3D games.
• None: The image is scaled using Nearest Neighbor which results in completely sharp pixels but may shimmer at non-integer factors.
  

Anti-Ringing

Anti-Ringing is a toggleable option (on/off) to reduce the appearance of ringing artefacts when using Lanczos family interpolation kernels. By default it is set to On when using Lanczos2 and Lanczos3.

Linear Light

Linear Light is a method of image color and brightness reproduction that may provide more accurate scaling and blending. Linear Light will also alter the appearance of scanline effects, which users may an improvement or not based on subjective preferences.

• Linear Light On: The RetroTINK-4K performs inverse gamma mapping at the start of the scaler pipeline and performs all operations in the linear light domain. The output is gamma encoded for SDR modes and PQ encoded for HDR modes.
• Linear Light Off: The RT4K performs all scaler operations in the gamma domain and only performs inverse gamma at the output if needed for color gamut transforms.
  

Assuming default SDR settings, for linear light to function properly, you have to manually set input factor and output factor to 2.4 in the Color Correction-> Gamma/PQ menu.
Enabling HDR in HDMI Output->Transmitter, Enabling Color Space Conversion in Color Correction->Color Space Conversion, or Adobe RGB/P3 in HDMI Output->Colorimetry will adjust Gamma/PQ settings by default to properly allow Linear Light processing.

More information on the benefits of linear light can be found here.

Scanlines

The RetroTINK-4K has customizable scanline generation which can recreate the look of various displays, including early LCD displays. Scanlines are an effect that simulates the appearance of blank scanlines on a display, similar to what you might see on older cathode ray tube (CRT) monitor or television screens. The effect creates generates black spaces between each visible scanline of video, simulating how lower resolution progressive signals would be presented on higher resolution (480i) displays.

Blank/Black Scanlines

The scanline Function determines what formula is used by the scanline generator to translate the replaced video scanline to "blank/black" scanline.

• Off: disables the scanline generator. Further settings in the Scanlines section will not have an effect if Off is selected.
• Exponential: A scanline formula that biases a thinner blank/black effect.
• Gaussian: A scanline formula that biases thicker than Exponential.
• Super Gaussian: A scanline formula that biases thicker than Gaussian.
• Linear: A scanline formula that biases thicker than Super Gaussian.
• Box: A scanline formula that biases thicker than Linear.

When using these "blank/black" scanline functions, The scanline generator creates different effects based on the brightness of the line it is replacing.

Setting the Strength value will adjust the maximum width of the scanline effect.
Adjusting Modulation will adjust how much the thickness of the scanline effect will change depending on brightness, for example, with a high Modulation value, the thickness of the scanline effect will become thinner for darker areas.

LCD Effects

The LCD functions behave differently than the "blank/black" functions. Designed to simulate the appearance of older LCD displays, the LCD functions will place each pixel in a surrounding black border.

• LCD Mono: Solid black outlines around each pixel.
• LCD RGB: Simulates subpixel artifacts (similar to how the CRT masks simulate phosphor artifacts).

With LCD functions selected, LCD Subpixel Str. will set how strong the LCD masking is, while LCD Vertical Str. will control the size of the horizontal line under each pixel.

Red Bleed

Enables red bleed.

Red Convergence

Adjusts red convergence from -10 to 10.

Blue Convergence

Adjusts blue convergence from -10 to 10.

Most of the Scanlines options do not appear correctly unless you have applied a crop, especially for systems that render higher than 240p like the PlayStation 2 and GameCube. Thus, we highly recommend cropping the picture in the Scaling / Cropping menu before beginning here.

Color Correction

The Color Correction Setup menu is where you can adjust the color values and interpretation of the video signal.

Gamma and PQ

The PQ stands for "Perceptual Quantizer".

Black Frame Insertion (BFI)

Black Frame Insertion (BFI) is a technique to improve motion clarity with high refresh rate monitors. As an example, a 60fps video source played on a 120hz monitor could have a black frame interstitially placed between every frame. The resulting "image-black-image-black" pattern can increase the perception of motion and fine details. If you have a higher refresh rate monitor, a customizable example can be viewed over at Blur Busters.

To enable BFI:

• Set a Supported Resolution: The RetroTINK-4K can generate BFI, but due to bandwidth constraints, BFI is limited to 1440p or lower resolution output. When the Output Resolution is not set to a high frame rate output (100 or 120hz) BFI Controls will be disabled.
• Set a supported Sync Lock Mode: BFI also cannot be enabled unless you are in Gen or Frame Sync Lock mode.

BFI Control

Black Frame Insertion (BFI) Settings

Strobe: Strobe controls how the output frame rate is divided into the input frame rate. As depicted in the diagram, with Strobe 1, the 60Hz input frame is flashed one time at 240 Hz. At Strobe 2, the 60Hz input frame is flashed twice at 240Hz, with black frames in between. Alternatively, a 60Hz source within a 120Hz output would display for 1/2 of the time 120Hz output window. Blur: Blur is a duty cycle modifier that works in relation to Strobe to change how many frames the source video is presented in relation to the black frames. In the example diagram (60Hz Source inside a 240Hz output), a Blur of 1 would display the source video 1/4 of the 120Hz window, a Blur of 2 would display the source video 2/4 of the 120Hz window, and a Blur of 3 would display the source video 3/4 of the 120Hz window. Some relationships of Blur and Stobe are locked, such as a 60Hz video source in a 120Hz output window, which would only allow a Blur of 1 (1/2 of the output 120Hz window).

More information about BFI can be found at Blur Busters.

Deinterlacer and Film

The Deinterlacer / Film Mode Setup menu allows you to adjust settings for use on interlaced sources, such as deinterlacing methods and Inverse Telecine.

While tweaking the options under the Mode and Motion Adaptive Settings sections, we suggest using the Pause Button to pause the video on a frame with motion. This will allow you to see the effects of the deinterlacing more easily.

Mode

CRT Simulation

The CRT Simulation algorithm is unique enough to warrant its own section. It's used to to simulate the way 480i content is displayed on a real CRT: each frame of a 480i image is actually only 240 lines, and each new frame switches to using lines that were unused in the previous frame. Because of this, CRT Simulation will appear identical to Bob deinterlacing unless you use one of the Scanline functions enabled in the Processing / Effects menu (since they simulate the unused lines), and are viewing interlaced content.

CRT Simulation will also cause your crop settings to be displayed incorrectly, so be prepared to redo your crop after enabling this feature.

• There is one thing to keep in mind when using this feature: the output frame rate of the RT4K must match the input signal's frame rate in order for the effect to be displayed correctly. This is important if you're using a PAL system, which run at 50 frames per second: if the RT4K is outputting at 60fps (as it usually does by default), the CRT Simulation will not appear correctly for PAL content!

Motion Adaptive Settings

Motion Adaptive settings apply only to the Motion Adaptive Deinterlacing mode, allowing you to adjust it to your liking.

• Sensitivity - Adjusts the sensitivity of Motion Adaptive, between Min, Medium, High and Max. The higher this is set, the more weaving will be present for moving parts of the screen, at the benefit of a stabler look for static parts of the screen. Many games will look just fine on the Min. setting, however several games may require Medium or higher. For example, Burnout 3: Takedown on PlayStation 2 has a subtle flickering and animated noise that throws off the Motion Adaptive Deinterlacer for still parts of the screen.

HDMI™ Receiver

The HDMI Receiver Setup menu is where you control how the RT4K handles Digital In video. This menu is only functional when the Digital In port is the currently selected Input. If it is, this menu can be quickly accessed by pressing the ADC button at the top of the remote when HDMI is selected as the input.

RGB and Component ADC

The RGB / Component ADC Setup menu is where you control how the RT4K handles analog inputs, such as the RCA, S-Video, HD-15 and SCART ports. This menu is only functional when an RGB or Component input is in use. If that is the case, this menu can be brought up by pressing the ADC button at the top of the remote when YPbPr, RGBS, RGsB, or RGBHV is selected as the input.

Auto Calibrate

Auto Phase

Any game screen is sufficient for automatic phasing, but it is recommended to use the 240p Test Suite or other sufficiently patterned screen for eyeballing results. whether you've set automatic sample detection using that menu, or you manually selected Decimation Factor in the ADC page, selecting Auto-Calibrate Phase makes the RetroTINK-4K automatically select the best Decimation Phase and Sub-Phase for your current picture and should give you the sharpest results. It is recommended you run this 3-5 times to make sure the same factors and phases are consistently chosen.

Auto Gain

The Auto Gain function will calibrate the gain levels for the current input, however it only works for RGB and YPbPr sources.

• To use Auto Gain, go to a game screen which has a patch of colour that should be pure white. When you enable the Auto Gain function, the RT4K automatically calibrates the Gain levels based on that white patch.

Auto Gain only works in calibrating the overall brightness Gain, not the individual color gain. You may need to manually adjust the individual colors a few ticks more for in the Gain section to get the true RGB code (255) for a given color. We highly recommend the use of the 240p Test Suite for this task.

Auto Gain must be calibrated on a per-console basis, meaning it will need to be set between different systems. This applies even across different units of the same system, such as two Super Nintendos, as their picture output will have degraded slightly differently.

Sample Rate Detection

The Sample Rate Detection menu is where you control how the RT4K automatically detects the sample rate of a given analog source. This menu is only functional when an RGB or Component input is in use.

Sample Rate Detection Overview

The RetroTINK-4K can take advantage of sampling and scaling algorithms to seamlessly change settings when it detects a horizontal resolution change. This is useful for most analog retro gaming consoles, but requires knowledge of their "Master Sampling Rate," noted below.

Master Sampling Rate Chart

Console Name	Master Sampling Rate	Available Resolutions
Super NES	3410	256x224, 256x239, 512x224
Sega Genesis/Mega Drive		256x224, 320x224
Sega Saturn
Turbo Grafx 16/PCEngine	2730	256x224, 320x224
Sony PlayStation		256x224, 320x224, 384x224, 512x224, 640x224
Sony PlayStation 2

Once you know the master Sampling rate of your console, set that console's ADC Sample rate in the "Sample Rate Detection" menu under ADC Sample Rate, and turn both "Auto Dec. Factor" and "Auto Dec. Phase" to "On." Once you enable those options, if you know which resolutions you'll use, scroll down to that resolution to enable that horizontal resolution's detection and the RetroTINK-4K should automatically switch to a different set of settings whenever it detects that particular resolution is used. This process will help automatically set Decimation Factor and Decimation Phase in the ADC setup.

SDP Decoder

The SDP Decoder Setup menu is where you control how the RT4K handles Composite and S-video. This menu can be quickly accessed by pressing the ADC button at the top of the remote when S-Video or Composite are selected as inputs.

Audio Input

The Audio Input Setup menu is where you'll find options regarding the RT4K's handling of audio., such as the sampling rate and overriding which audio input is in use.

System

The System selection of menus relate to the RetroTINK-4K itself, including the On-screen display, firmware updates, and displaying various status screens.

OSD and Firmware

Banner Image

This menu allows you to load in your own Banner. The SD card comes pre-loaded with a default RetroTINK-4K banner, FirebrandX's banner displaying Firebrand from Demon's Crest, and two moon banners (both of which intentionally do not display the moon in a perfect circle).

Here's some information on how banners work on the TINK-4K:

• Banners are stored in the "image" folder of the SD card.
• Banners must be 24-bit BMPs in order to work with the RT4K.
• 320 x 128 is the recommended pixel dimensions. It can be larger, however only the upper-left 320x128 pixels of the image will be drawn.
• An RGB value of "255, 0, 255" (a pink colour) will be treated as transparency.
• If a Profile doesn't have a banner image specified, the file named "default.bmp" will be loaded instead. This lets you determine your own default banner image.

On Screen Display

This section allows you to adjust facets of the On Screen Display, including the menu.

• Position - This lets you set whether the menu is displayed on the Left side of the screen, the Center, or the Right side of the screen. This is set to "Left" by default.
• Auto-Off - Lets you determine how long the menu will wait before disappearing (as if you pressed the menu button). This is set of "Off" by default, but you can set it to turn the Menu off after up between 10 - 100 seconds (and anything in-between in 10 second increments).
• Hide Input Res. - Turning this on will mean the RT4K will not display the current input and resolution in the top-right corner of the screen every time it changes. This is useful if you're capturing or streaming games that switch resolutions.
• Enable Debug OSD - This option allows you to permenantly display one of the three Status Pages or the Diagnostic Console.

Firmware Update

This option allows you to Check the SD card for the two files needed for installing new firmware to the RetroTINK-4K. For more information on how to install new firmware, head to the Firmware Updates section.

Status

Displays the Status menu, letting you learn more about the current status of the RetroTINK-4K. For more information, visit the Device section of our GUI Map.

Diagnostic Console

Shows the 30 most recent actions in the RetroTINK-4K's operations. Or something?

About

Displays the About Page, containing the following information:

• About
  • Device - Displays information about the RT4K's hardware version.
  • FW Version - Displays the current firmware name.
  • Device ID - Displays the ID of the RT4K.
• Resources
  • Website - www.retrotink.com
  • Discord - discord.gg/jE6deAhjCM
  • Wiki - consolemods.org/rt4k
• Thanks!
  • "This project would not have been possible without the support of everyone who has helped over the years. Thank you all so much for everything and we hope this device brings you countless hours of joy!"

System-Specific Methodology

The System-Specific Methodology section is all about highlighting how you can use the RetroTINK-4K's various features to improve the experience of using your video game systems beyond just plugging them in. This can range from setting 1:1 pixel aspect ratio for Super Game Boy on the SNES, to dovetailing with the Sharpscale Plugin on the PlayStation TV.

NES / Famicom

The Famicom (or Family Computer) is the original Japanese version of Nintendo's landmark console, while the NES (or Nintendo Entertainment System) was released in all other regions. All Famicom / NES systems will be marked as such on the front, so simply read that to tell which one yours is (particularly useful regarding the top-loading redesigns). These systems render games in 256x224.

• The NES family renders and outputs all audio in mono via the white RCA jack (left speakers). To account for this, go to Advanced Settings > Audio Setup, then set Input Swap to "Mono (Left)".
• Some NES family games, like Super Mario Bros. 3, have visual errors visible on the left and right sides of the screen. These can be removed from view using the cropping tools.

The NES / Famicom can only output either Composite video or RF (with one rare exception). You will need at least a composite signal to connect directly to the RT4K. Use the list below to tell which one your system outputs:

• Composite signals are supported by the RetroTINK-4K. This can be used on either the front yellow plug, or the rear green plug.
  • Original "Front-loading" NES (NES-001).
  • Top-loading "AV Famicom" with the rounded power switch and flat cartridge slot.
  • Sharp's "Twin Famicom".
  • Sharp's "Famicom Titler" (also capable of S-Video).
• RF signals are not normally supported by the RetroTINK-4K. These models support RF output:
  • Original Famicom w. hard-wired controllers.
  • Revised "Top-loading" NES with a rounded cartridge slot and power switch.
  • The RF Modulator output from the original "Front-loading" NES-001, which has softer sound compared to the the sharper Composite output.

Super NES / Super Famicom

The majority of Super NES / Famicom games run in 256x224 resolution, while a select few games run with a mix of the following: 512x224 in the whole screen for menus, 256x224 for most of the image while running 512x224 over certain parts of the screen to create transparency effects, or the same but using 512x224 resolution to allow sharper text on the screen. It is recommended to run the Super NES in 512x224p mode to make sure you get all available detail. (https://consolemods.org/wiki/AV:RetroTINK-5X_Pro#512_%22Hi_Res%22_Games)

We recommend using a Super NES model number SNS-001, or Super Famicom model number SHVC-001, and an RGB SCART cable wired for Sync-on-Luma, as this works with both of the aforementioned models. There are internal revisions of these models, noted as "1-Chip" on the motherboard, and the 1-Chip-03 does not work with Composite Sync. There is a revised model, SNS-101 and SHVC-101, also known as the Super Nintendo Junior. This model only supports composite video.

[Picture Here: 1-Chip without gain adjustments vs 1-Chip with gain adjustments]

As noted, there are revisions of the original model Super NES, noted by the "1-chip" on the motherboard. The 1-chip boards have sharper yet brighter video, while the non-1-chip boards have a "smeared" and slightly darker look. We encourage using the auto-gain functions in the ADC to correct the video on both models.

[Picture Here: Non-1-Chip vs 1-Chip]

Profile included for automatic switching between 512 and 256 in Display Aspect Ratio, for both SCART and HDRV YPbPr cables.

Super Game Boy

The Super Game Boy Cartridge allows you to play original style Game Boy and Game Boy Color cartridges on your TV using the Super Nintendo, and adds borders. Once dialed in, Game Boy games are rendered in a 160x144p window inside a 256x239p canvas. However, Game Boy games were expected to be displayed on the square pixels of their screens, unlike the rectangular CRT pixels that the SNES expects.

• For correct Super Game Boy pixels, go to Advanced Settings > Scaling/Cropping, then set Aspect Correction to "1:1 (Sq. Pixel)".

[Picture Here: Generic SGB vs Optimized 15x]

Profile included to maximize the Game Boy window to the screen.

Nintendo 64

Unfortunately, no stock Nintendo 64s support RGB without modding. All stock N64s support Composite, all NTSC N64s support S-Video, French N64s support SECAM S-Video, and some PAL N64s do not support S-Video at all.

All N64s have 3 levels of video processing that keep it from being as sharp as the PlayStation and Saturn:

1. All games scale their image to 640 pixels wide. Many games were rendered at different resolutions but the N64 will scale to 640.
   • Many games render at 320 pixels wide and, as a trick, you can double your ADC Decimation factor to "correctly" render games in their original resolution. This trick only works for games that render at 320 pixels wide, and do not work for games that render at other resolutions that are not 320 or 640 pixels wide.
2. Software level anti-aliasing. This can be disabled by patching ROMs or using a Gameshark to disable the effect.
3. Hardware level anti-aliasing. This can't be disabled without a physical mod.

[Picture Here: AA enabled vs AA disabled]

[Picture Here: a 320 game with the trick used vs left at 640 (should be the same)]

[Picture Here: a non-640 or 320 game with the trick used (should look worse)]

Pokemon Stadium Game Boy Tower

Pokemon Stadium's Game Boy Tower allows you to play Pokemon games on your TV, similar to a Super Game Boy, and even uses the Super Game Boy borders. The issue, however, is the scaling noted above. These games render at 160x144p inside a 256x239p canvas, which is then scaled to 640 pixels wide. You will not get a sharp picture out of this setup due to that factor alone. It is recommended to play in a generic or default profile.

[Picture Here: SGB vs Pokemon Stadium]

Nintendo GameCube

For the purposes of use with the RetroTINK-4K, it is highly recommended to use a DOL-001 GameCube, which has the digital out port, and an Insurrection Industries Carby which outputs crisp digital video and can connect to the Digital Video input port of the RT4K. If you insist on buying YPbPr cables, we can only recommend the OEM D-Terminal cable with a D-Terminal to Component adapter, or the OEM component cable.

Most GameCube Games will run at 480p, a progressive mode is activated by holding B when the GameCube boots up a game.

Swiss, the Anti-Flicker Filter, and Horizontal Frame buffer Width

While Most GameCube games run at 480p and progressive mode is relatively easy to access, many GameCube games use an "anti-flicker-filter" by default, which will soften the image. Most of these filters can't be turned off in-game, but the homebrew software Swiss will allow you to boot games, including your own disks, with the anti-flicker filter turned off. As an added bonus, newer versions of Swiss automatically turn the filter off and boot your game in 480p.

[Picture Here: game with anti-flicker filter on vs off]

[Video here: Smash Bros Melee turning the flicker filter on and off]

A few GameCube games scale their image to fit the console's frame buffer before output. Swiss allows you to turn this off and shows the image at its original framebuffer width, and you can use the RT4K to scale it back, for a small sharpness gain.

[picture here: Framebuffer width left alone and the framebuffer width option turned on, with the RT4K used to scale back to the intended resolution] (I don't know what game to use)

240p Games

There are two GameCube games that run at 240p: Megaman X Collection, and the NES games in the Zelda Collector's Edition Promotional Disc. This means you do not have to enable 480p to run those games and can sharply scale these games on the RT4K.

[Picture Here: Megaman X on Super NES vs GameCube]

Game Boy Player + Game Boy Interface

The Game Boy Player is a popular add-on to the GameCube that allows you to play Game Boy, Game Boy Color, and Game Boy Advance games on your TV. The Game Boy Player Disk does not sharply render games onto the screen, but you can use the homebrew software Game Boy Interface to sharply render games into the RT4K. A specific flavor of GBI was created to take advantage of the Insurrection Industries Carby and the TINK 4K's Digital Video input. Please use files gbihf-rt4k-HDMI.cli, gbihf-rt4k-HDMI.dol+cli or gbihf-rt4k-HDMI.gci included with GBI and follow the instructions noted here.

[Picture Here: GBA game on RT5x scaled to 4k (12x scale) vs RT4K (13x scale)]

[Picture Here: GBC game on RT5x scaled to 4k (12x scale) vs RT4K (15x scale)]

Profiles included for 13x scaled GBA games and 15x scaled GBC games.

Nintendo Wii

The Nintendo Wii is a very versatile console: it plays GameCube Games, Wii Games, and many classic retro titles through emulators as part of the Virtual Console lineup. The Wii also has easy to find YPbPr component cables and can easily support 480p across all Wii software through its component cables, making it a popular option for playing GameCube games. The Wii only supports 3 resolutions: 720x240p, 720x480i, and 720x480p. Please read on for more information on getting the sharpest possible picture from a Wii.

Profile included for basic generic output. It is recommended you use this for basic Wii use.

Virtual Console

Many Virtual Console games output at 240p when the Wii is in SDTV mode, and they will line double to output at 480p in EDTV mode. All virtual console games scale the image to 640 pixels wide, so it is recommended you use the default or generic profiles for playing virtual console games. Also of note: NES Virtual console games are rendered many shades darker than an original console, as an anti-epilepsy measure.

[Picture Here: Donkey Kong on Super NES vs Donkey Kong on Wii with generic settings]

USBLoader GX, and Counteracting the Anti-Flicker Filter, 480p LPF, and the Framebuffer Video Width

Homebrew called USBLoader GX allows you to activate or deactivate code before running games, even on your disks.

Most Wii games will apply an anti-flicker filter, even at 480p, which results in a softer picture. Use USBLoader GX's options to turn this off for Wii Games. If you wish to run GameCube games, you will need to turn the anti-flicker filter off separately in either Nintendont or Devolution, but USB-Loader GX does have these options in its menu.

[Video here: Super Smash Bros Brawl's settings menu turning the anti-flicker filter on and off]

There is an option in USBLoader GX called the "480p pixel fix" which makes the game look much sharper. It only works with RVL-001 models with the internal CPU-01 motherboard.

[Picture here: Wii game with 480p pixel fix off vs on]

You can get even sharper picture from the Wii by enabling the "Video Width: Framebuffer" option in USBLoader GX. This will make games output in their original rendering resolution, which you can then rescale using the RT4K to get a much sharper picture than originally intended at the "correct" aspect ratio. As an added bonus, NES and Super NES games will render at 512x224p with this option turned on, which you can use a doubled decimation factor to treat a game like its original 256x224 resolution, and get picture on par with their original consoles.

[Picture Here: Megaman X Super NES Optimal vs Wii Optimal]

Nintendo Wii U

It is highly recommended to use the Wii U's HDMI output instead of its Component output. This is because the analog video is duller, and has less sharpness (even compared to Component from the PS3 and 360).

• The Wii U's HDMI only outputs in limited range. To account for this, go to Advanced Settings > HDMI Receiver, then set Input Range to "RGB Lim.".

Nintendo Switch

Nintendo Switch Online Games

it is highly recommended to use 1080p output for the NSO emulators and turning on "Pixel Perfect" in their settings under "Game Screen" and to also turn off "Show controls in game" under "Control Display," and to turn off "reproduce classic feel" on the Game Boy and Game Boy Advance apps. This way, all games output a perfectly integer scaled, line-multiplied output for their games.

[Picture here: Donkey Kong Country Super NES Optimal vs Switch Optimal vs Switch no adjustments] For a 256 wide game

[Picture here: Ristar Genesis on Wii Optimal vs Switch Optimal vs Switch no adjustments] for 320 wide games

[picture here: Mario & Luigi Superstar Saga on GBI 13x vs Switch Optimal 13x vs Switch no Adjustments 12x] for GBA games

[Picture Here: The Legend of Zelda, Oracle of Ages on GBI 15x vs Switch Optimal 15x vs Switch no adjustments 14x] for GBC games

SEGA Master System

The original model of the Master System supports Composite and RGB output (S-Video is not supported without mods). The second model, the "Master System II", cannot be used with the RetroTINK-4K without modding, as it only supports RF output.

• Master System games are infamous for having borders of solid colour around the game graphics. These can be removed by going to Advanced Settings > Scaling/Cropping and using the Input Crop trim tools, but be mindful! Master System games can use two horizontal resolutions: 248 pixels and 256 pixels, and some games will use both of them. The safest option is to crop to a 256 pixels wide screen, which will leave a column on the left-hand side of 248 pixels wide screens. You could also have an additional profile just for 248 pixels wide screens.
  • The Auto Crop tools will not work here, as they will consider the coloured border to be part of the image (it technically is, if still unsightly).
• The Master System also has rather dim video output compared to other systems. You can fix this by going to Advanced Settings > RGB/Component ADC and adjusting the Gain while using the 240p Test Suite. You can also use the Auto Calibrate Gain feature, which works best if there's a patch of solid, pure white somewhere on the screen.

SEGA Genesis / Mega Drive

Recommended output: RGB

For practicality, "Genesis" refers to both the SEGA Genesis and the Mega Drive (it's Japanese and European name), as they are functionally identical as far as the RetroTINK-4K is concerned, outside of NTSC and PAL standards.

• The SEGA Genesis has three "240p" output resolutions: 320x224, 256x224. A third resolution, 480i, is only known to be used in the 2 Player VS modes of Sonic the Hedgehog 2 and Combat Cars.

Certain Genesis games will display coloured dots along the bottom edge of the screen. Known as CRAM (Colour RAM) dots, these would have been in the overscan area of most CRTs and thus invisible to the player, but are quite prominent on modern displays. You can hide them by going to Advanced Settings > Scaling/Cropping and adjusting the Bottom Trim value. You should not use Auto Crop, as it will consider the CRAM dots to be the bottom edge of the picture.

Composite effects. see this portion of the 5x wiki https://consolemods.org/wiki/AV:RetroTINK-5X_Pro#Genesis_Dithering

SEGA Saturn

Recommended output: RGB

SEGA Dreamcast

Recommended Output: RGBHV

Sony PlayStation

All Sony Playstation models support RGBS. It is recommended to use a well shielded SCART cable that uses Sync-on-Luma.

Resolution Switching

PlayStation games will switch resolutions often, usually horizontal resolutions like 256, 320, 384 and 512, but occasionally vertical resolutions as well with 480i. The PlayStation is a perfect use for the Automatic Sampling Detection feature of the RT4K. To help with switching vertical resolutions quickly, please enable Triple Buffer in the RT4K's Output menu.

see this part of the 5x wiki https://consolemods.org/wiki/AV:RetroTINK-5X_Pro#Resolution_Switching

Profiles included will automatically switch to all resolutions. You may want to consider researching your game collection and see if you can turn off any resolutions that you won't use, for faster response from the auto sampling detection.

Sony PlayStation 2

The PS2 outputs 240p, 480i, 480p, and 1080i, and supports RGB as well as YPbPr. For simplicity, it is highly recommended to use YPbPr cables because the RT4K will automatically detect and switch to all those resolutions seamlessly. The PS2 will use RGBS for 240p and 480i, but will switch to RGsB for any resolutions above that. While the RT4K supports RGsB, it does not automatically switch from RGBS to RGsB, you will need to change the input manually.

All PS2 games will output either 512 pixels wide or 640 pixels wide. [sic]

PS1 Backwards Compatibility

PS1 games on PS2 use a different set of optimal sampling numbers than the PS1 console.

Sony PlayStation Portable

PSP models PSP-2000, PSP-3000, and PSP-N1000 (aka PSP GO) can output to a display. It is highly recommended you use component cables with the RT4K.

PSP games are rendered at 480x272p. When they are displayed on a television with component cables, they render a 480x272p picture inside of a 720x480p canvas. You can use the RT4K to upscale the image to fit the screen. You will get the sharpest integer scaled picture at the expense of cutting off 2 vertical pixels.

[Picture here: PSP left alone (4.5x scale) vs PSP scaled to 8x]

PSone Classics on PSP

PSone Classics are PS1 games played on the PSP, and use a different set of optimal sampling numbers than the PS1 and PS2 consoles.

• PSone Classics can be output at their original resolution. On the PSP, go to Settings > Connected Display Settings, then set Component / D-Terminal Output to "Interlace".

[picture here: ps1 console optimized vs ps1 classic]

Sony PlayStation 3

The PS3 supports HDMI, which is recommended for the sharpest possible picture with the RT4K.

• The PS3 supports outputting PS3 games at 720p, 1080i and 1080p, which the RT4K supports. However if you do not have an option enabled (such as 720p), the PS3 will use a different one. To avoid this, on the PS3 go to Settings > Display Settings, then pick "Video Output Settings". In the new menu, choose "HDMI", then "Custom". In the list, ensure that 720p, 1080i and 1080p are all selected, then press Right and then X to save your settings.
• While the PS3 does support up to 1080p using component cables, it's softer compared to HDMI output. However many users choose it anyway, as the PS3's HDMI output always uses HDCP (High-bandwidth Digital Content Protection) with no option to disable it like on PS4 and PS5.

[Picture Here: HDMI vs YPbPr]

PSone Classics on PS3

PSone Classics on PS3 can render to 480p, but scale the image to fit the 4:3 aspect ratio. For the sharpest picture, use these settings:

• On the PS3, go to Settings > Game Settings, then set both PS - Upscaler and PS - Smoothing to "Off".
• On the RT4K, go to Advanced Settings > Scaling/Cropping, then set Vert. Pre-Scale to "1/2".

[Picture Here: PS1 console optimized vs ps1 classic]

Sony PlayStation TV

The PlayStation TV (called the Vita TV in Asia) allows you to play Vita, PSP, and PSone Classics on your TV through HDMI. By default, all output from the PlayStation TV is soft because of the following factors:

1. All software has a bilinear filter applied
2. All software is scaled to the PSTV's selected output resolution
3. Vita software is internally scaled to 960x544p regardless of its original rendering resolution. This applies to Vita handhelds as well
4. PS1 Classics are unevenly, horizontally scaled to 4:3.

To counteract this for the sharpest possible picture, we highly recommend installing custom firmware on your PSTV and installing the Sharpscale plugin to counteract all the above effects applied to the PSTV.

Sharpscale Plugin

See an overview of sharpscale here. The following suggestions only work when sharpscale is enabled with the following options:

[picture of sharpscale plugin with the following settings enabled]

PSTV Sharpscale Options

Option Name	Option Choice
Scaling Mode	Integer
PS1 Aspect Ratio	Pixel
Scaling Algorithm	Point
Unlock Framebuffer Size	Off

Vita Games

When Playing a Vita Game, the PSTV outputs a 960x544p picture inside of a 1280x720p canvas. Use the following settings to get the sharpest integer scaled picture for Vita Games. These settings cut off 4 vertical pixels from Vita games.

RT4K PSTV Vita Settings

Scaling/Crop Setup
Top Trim	-90
Bottom Trim	-90

[Picture Here: Steamworld Dig 2 with sharpscale disabled vs enabled and optimized]

PSP Games

The PSTV also outputs a 960x544p picture inside of a 1280x720p canvas. Use the following settings to get the sharpest integer scaled picture for PSP games. These settings cut off 2 vertical pixels from PSP games.

RT4K PSTV PSP Settings

HDMI Receiver Setup
Input Pixels	2
Scaling/Crop Setup
Top Trim	-45
Bottom Trim	-45
Vert. Pre-Scale	1/2

[Picture Here: Final Fantasy IV with sharpscale disabled vs enabled and optimized]

PSone Classics on PSTV

Sharpscale will allow you to get the sharpest picture for PS1 games, but the behavior is not optimal. With the Integer Scaling Mode setting enabled in Sharpscale, some resolutions will use the full vertical space, and others will only scale to 480 vertical pixels inside 720p. it is recommended you look at the resolutions supported by your game before you use sharpscale with the RT4K and see if it is worth avoiding the headache. If you set PS1 Aspect Ratio to 4:3 in the PSTV's settings, the PSTV will force all games to fit, but they will not evenly scale horizontally, resulting in shimmering pixels.

[Picture Here: PS1 console optimized vs pstv optimized]

Microsoft Xbox

Preferred output: YPbPr.

Up to 720p available with custom firmware

Microsoft Xbox 360

The cable you should use for your Xbox 360 may vary by model.

• For Xbox 360 models made in 2007 or later, HDMI output is available and should be your first choice, since HDMI cables are readily available.
• The earliest Xbox 360 models only offer A/V video output. Unlike the PS3 and WiiU however, the 360's component video is quite sharp, so it's a good alternative to HDMI if that's what you need / prefer. A/V output was standard alongside HDMI for most of the 360's life, except for the 360 E revision.

Profile Repository

This section catalogues all of the profiles available on the RetroTINK-4K's included SD card.

Generic Profiles

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Downscaling

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Console Specific

3DO Interactive Multiplayer

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Atari Jaguar

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Microsoft Xbox

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Microsoft Xbox 360

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Neo Geo AES

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Entertainment System (NES)

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Super Nintendo / Super Famicom

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo 64

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Gamecube

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Wii

Profile Name	Download 1	Profile Description
Generic	Download 2	Recommended for use with an unhacked Wii, optimized for 240p, 480i, and 480p.
VC 256		Recommended for use with the NES and Super NES Virtual Console games that output 256 wide pixels on a hacked Wii. Make sure to switch "Video Width" to Framebuffer in USBLoader GX.
VC ~256		Recommended for use with games that should be 256 pixels wide but are scaled to 320 pixels a hacked Wii. Make sure to switch "Video Width" to Framebuffer in USBLoader GX. DO NOT USE with games that actually output 256 pixels wide.
VC 320		Recommended for use with Virtual Console games that output 320 pixels wide on a hacked Wii. Make sure to switch "Video Width" to Framebuffer in USBLoader GX.

Nintendo Wii U

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Nintendo Switch

Profile Name		Profile Description
N64 720	Download 1	Set the Switch to 720p to use this profile. NSO N64 games render at 720p. This profile is for use with scanlines to approximate the look on a CRT, not for additional sharpness. If you want a sharper picture, use the default profile.
NSO 256	Download 2	To be used with the NES, Super NES, and Sega Genesis Nintendo Switch Online emulators when the game has an 8:7 aspect ratio.
NSO 320	Download 3	To be used with the Sega Genesis Nintendo Switch Online emulator when the game has a 10:7 aspect ratio
GBA		This profile is for use with any GBA game on Switch, including the NSO GBA app as well as ports of GBA games that are scaled 6x to 1080p. This allows for a 13x scale to 2160p, where a default profile would only scale games 12x.
GBC		This profile is for use with any GBC game on Switch, including the NSO GBC app as well as ports of GBC games that are scaled 7x to 1080p. This allows for a 15x scale to 2160p, where a default profile would only scale games 14x.

Phillips CDi

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Pioneer LaserActive

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

SEGA Master System

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

SEGA Genesis / Mega Drive

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

SEGA Saturn

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

SEGA Dreamcast

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation 1

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation 2

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation 3

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PSP

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Sony PlayStation TV / Vita TV

The Playstation TV profiles require a hacked PSTV and the Sharpscale plugin to take advantage of the potential sharpness the PSTV can give. If your PSTV is not hacked, please use the default profile.

For the following profiles, please set the following options in Sharpscale:

PSTV Sharpscale Options

Option Name	Option Choice
Scaling Mode	Integer
PS1 Aspect Ratio	Pixel
Scaling Algorithm	Point
Unlock Frame Buffer Size	Off

Profile Name		Description
PSVita	Download 1	The PlayStation TV outputs a 544p window onto a 720p canvas. Upscaled 4x to fit 2160p. Cuts off 4 pixels vertically
PSP	Download 2	Sets Decimation Factor to 2 and Prescale to 1/2 The Playstation TV outputs a line-doubled 272p window into a 720p canvas. Upscaled 8x to 2160p. Cuts off 4 pixels vertically.
PS1 Generic		The Playstation TV will output the PS1 game to an integer scale of its signal that will fit inside 1280x720p. Use this profile for PS1 games that switch between many resolutions often. 480i will scale 1x. 512x224p and 640x224p will scale 2x. 384x224, 320x224, and 256x224 will scale 3x.

The following profiles require a slight change in Sharpscale settings. These profiles are best used with games that stick to one resolution for the majority of their gameplay. Do not use these with Chrono Cross or Silent Hill, their menus will cut off vertically

Sharpscale Settings

Option Name	Option Choice
Scaling Mode	Real
PS1 Aspect Ratio	Pixel
Scaling Algorithm	Point
Unlock Frame Buffer Size	Off

PSTV Profiles: PS1 Pixel Aspect Ratio

Profile Name		Profile Descriptions
PS1 256	Download 3	Use for PS1 games that are primarily 256x224.
PS1 320	Download 3	Use for PS1 games that are primarily 320x224.
PS1 384	Download 4	Use for PS1 games that are primarily 384x224.
PS1 512	Download 4	Use for PS1 games that are primarily 512x224
PS1 640	Download 5	Use for PS1 games that are primarily 640x224

TurboGrafx-16 / PC Engine

Profile Name 1	Download 1	Description
Profile Name 2	Download 2	Description

Classic Mini Consoles

256	Download 1	Use with mini consoles that output a 3x integer scale of 8:7 aspect ratio games. Primarily used by NES and Super NES Classic Mini consoles. Note: The Famicom Classic Mini needs Digital Video Color space changed to "Limited"
320	Download 2	Use with mini consoles that output a 3x integer scale of 10:7 aspect ratio games. Primarily used by Sega Genesis Classic Mini.

Analogue Pocket

GBA	Download 1	Set Scale size to 6x in Pocket GBA settings. Outputs 13x scaled GBA games where the default profile would normally scale to 12x. Do not use with Pocket scanline effects.
GBC	Download 2	Set Scale Size to 7x in Pocket GBC settings. Outputs 15x scaled GBC games where the default profile would normally scale to 14x. Do not use with Pocket scanline effects.

Computer Specific

FM Towns

FM Towns computers once hitting white desktop variants output different video displays with some models performing internal upscaling conversions from 24khz to 31khz as well as some models performing 15khz to 31khz with adjustments in the TBIOS configuration file. EA and Pentium type desktops only output 31khz video modes. The below profiles are meant for all towers, UX, UG, UR, HG and HR models which are all models that do not perform internal conversion.
FM Towns will require a custom profile for any displays at 24khz

24Khz

Download 1

24Khz Display Mode

Sharp X68000

Sharp X68000 is unique with its outputs primarily being 15khz and 31khz. A few games have hidden selectable 24khz display modes.

Profile Name 1	Download 1	24Khz Mode in XXXX Game.
Profile Name 2	Download 2	24Khz mode

PC-8801

PC-8801 computers will output either 15khz or 24khz depending on the dipswitch settings in the back. If dipswitch settings are incorrect, games will refuse to boot and crash the computer. The 15khz VGA detection in the RT4K works very well for PC8801 and most video modes won't require a profile.
A 24khz signal will require a profile to display properly.

24Khz Mode in BASIC

Download 1

24Khz Mode in BASIC.

Notes

Deinterlacer -> -> Motion Adaptive Settings -> Sensitivity

---

(medium and high options might be might be reversed) Controls combing effect at costs of sharpness. Low = less combing.

Deinterlacer -> -> Motion Adaptive Settings -> Interpolator:

---

Basically controls how the "bob" portion of the MA is calculated. The bob is either taken from the line above, line below or the average of the upper and lower lines BFI. It's a matter of preference. I think either Top or Bottom interpolator looks a little sharper. Average is softer In the end it doesn't matter too much because Bob is only used during motion when it is hard to see detail anwyays

Deinterlacer -> Motion Adaptive Settings -> Detector:

---

This is a little complicated to explain... but let me try basically symmetric adds one frame of lag but the motion detection may be better. Because it is looking "one field into the future" idk if its really better tho in real life

HDMI -> BFI Control

---

-Strobe: How much the frame is divided down (i.e. 1 = divide by 2, 2 = divide by 3, 3 = divide by 4) from input to output -Blur: How many frames are ON vs OFF. So let's say we are converting 60 Hz -> 240 Hz. Blur = 1, ON, OFF, OFF, OFF. Blur = 2 is ON, ON, OFF, OFF -LCD Saver - inverts the pattern of the BFI to avoid renetion. But every few minutes u will see a flicker

Custom Mode Lines

---

#RT4K Custom Mode Line Format
#H active, H front porch, H sync, H total blank, polarity (1 = pos, 0 = neg)
#V active, V front porch, V sync, V total blank, polarity (1 = pos, 0 = neg)
#Nominal frame rate (floating point)
#Text name

Launch Information

https://www.retrotink.com/post/introducing-the-retrotink-4k

User Guides

The User Guides section contains guides on how to accomplish a desired task that may require the use of multiple RetroTINK-4K functions, or are applicable to multiple systems.

Defeating Dithering

Dithering is a technique many games used in tandem with the blurring effect of a video cable (like Composite) and a CRT. The idea is that the video cable and display blend the dither patterns together, to accomplish tricks like transparency or higher color depth. When using high-quality cables like RGB-SCART and Component, dithering can become very apparent, and many users may find them unsightly. The RetroTINK-4K has an option that can help:

• Go to Advanced Settings > Processing / Effects, then set Hori. Kernel and Vert. Kernel to "Bilinear Soft" as needed. This blurs the edges of the pixels to disguise the dithering.

The cost of applying this effect is that the image will of course be rather blurry. Adding some scanlines (also in the Processing / Effects menu) can help alleviate this somewhat; don't forget that HDR will help brighten the image back up. If the dithering is only vertical stripes (like the waterfalls in Sonic the Hedgehog or the water in Kirby's Dream Land 3), you could alternately use Bilinear Sharp on the Hori. Kernel, for a slightly sharper appearance.

Dithering Gallery

Sonic the Hedgehog - Bilinear Sharp Vert. and Hori.

Sonic the Hedgehog - Bilinear Soft Vert. and Hori.

Sonic the Hedgehog - Bilinear Soft on Vert. only w. Scanlines

Custom CRT Shadow Masks

The RT4K allows for the use of custom CRT shadow mask overlays.This is primarily intended to give an effect similar to CRT slot masks, as opposed to scanlines. The RT4K uses shadow mask images, tiling them across the screen.

• Custom CRT masks must be saved as 32-bit .BMP files.
• The maximum dimensions of a CRT mask is 16 x 16 pixels. They can be smaller, which will result in denser tiling of the mask across the screen.
• A color value of 128 will be neutral,while 0 will completely black out the corresponding pixel. 255 will double the input value (although this will be clamped).
• CRT masks will NOT adhere to the pixel grid like the RT4K's scanlines will. If you need them to adhere to the pixel grid, you'll need to have your shadow mask image match the dimensions of a single upscaled pixel, but this will vary depending on many factors, and so should be paired with a specific Profile you have in mind.

Downscaling (pre-scale) Basics

Downscaling is the act of taking a picture that's one size and reducing it to a lower resolution. This process is essential for applying thicker scanlines to a high resolution image.

• IMPORTANT: Downscaling is different from the process of having the RetroTINK-4K output a resolution lower than the source. That can be accomplished with a custom Output Resolution modeline.

For HDMI sources, this will be handled in Advanced Settings > HDMI Receiver Setup. Input Pixels determines how much the signal is "divided" by (with the number in brackets marking the effective vertical resolution). Output pixels also does something, I've heard. Initial Phase adjusts which pixels "survive" the division.

FAQ / Troubleshooting

Hardware Questions

Is there only 4k output? The RT4K supports any output up to 18Gbps, or 3840x2160p. You have common resolutions available on the remote, and more in the Digital Output menu.

Does the RT4K pass through 4k input? Is the input HDMI 2.1? No. The maximum supported input is 1080p60.

What is the recommended power for the RT4K? Please use a power supply rated at 5v2A, or 10W, to power the RT4K.

Can I use my TV’s USB port for power? Most TV USB ports do not supply enough power for the RT4K. Please use a power supply rated at 5v2A, or 10W, to power the RT4K.

Does the RT4K use USB-C or Micro USB? The RT4K uses USB-C for power.

I see a lot of analog ports! Can any be used for output? The only port used for output is the HDMI Out port. There are no plans to use the analog ports for output at this time.

Is the RT4K rack mountable? The case is not rack mountable. You may want to search for community members creating their own rack mount solutions.

Is there an S-Video or Composite port? If so, where are they? There is a discrete S-Video and Composite port in the front of the device, behind a sliding door. There are other ways to feed S-Video and Composite video to the RT4K; please check the Inputs section for more information.

The SCART port is loose! Can I get a return? All modern SCART input ports are sourced from the same factory, and they are all slightly loose and therefore “work as intended.” Please look into a SCART clamp with screws, similar to a VGA cable.

What kind of memory card should I use? The RT4K comes with an 8GB full-sized SD Card formatted in FAT32. The maximum size supported is 32GB.

Is there Wifi? No.

Is there Bluetooth? No.

Is there surround sound support? The RT4K passes through up to 8 channels LPCM via HDMI, supports compressed surround sound through optical audio, and passes through DPLII as this is encoded in stereo.

What’s the VGA Pin Layout? Please see the Inputs section of the wiki.

What’s the SCART Pin Layout? Please see the Inputs section of the wiki

Is there eARC support? [sic]

Software Questions

Does resetting or updating the unit delete my profiles? Profiles and settings are stored in the SD Card. Barring a complete revamp of the way the RT4K works, your profiles should work between power cycles and updates if they’re saved on the SD Card. Settings do not stay set between power cycles, but you can set a profile to return to when you cycle power or make an update.

Can you run emulators on the FPGA? There are currently no plans to support emulators or cores on the RetroTINK-4K hardware itself.

Does the RT4K automatically switch resolution? The RT4K can detect changes in vertical resolution and switch to settings for each resolution. These are: 240p, 480i, 360p (GBI), 480p, 720p, 1080i, 1080p, and one additional custom resolution.

For 240p, 288p, 480i and 576i sources, the RT4K has an experimental feature to automatically detect changes in horizontal resolution. Please see the Sample Rate Detection section of the wiki for more information.

Does the RT4K automatically switch to a detected source? >No. You will have to select your input manually.

Is there serial communication support through USB? The hardware is capable, but there is currently no support to communicate through the USB port.

Is there RS232 communication support through the VGA Port? The hardware is capable, but there is currently no support to communicate through the VGA port.

Does the RT4K support Game-ID? There is currently no way to communicate information to the RT4K.

Does the RT4K support [240p, 480i, 540p,786p, 1080i, 1536p] output? Does it support my HDCRT? The RT4K can support most progressive outputs that do not cross the 18Gbps threshold. If your output is not available in the HDMI Output section, please create a custom modeline file for that output.

At this time, the RT4K does not support interlaced outputs such as 480i or 1080i.

Compatibility with your HD-CRT depends on whether they like any of the supported outputs of the RT4K and take HDMI.

Support Questions

The output is too sharp! It’s too blocky! If you feel the output is too sharp, try the following steps in this order

1. Make your way into the Image Processing menu (press SFX on the remote) and try changing the scaling algorithm to suit your preferences.
2. Try activating scanlines in the Image Processing menu and see which suits your needs
3. As a last-ditch effort, open the Digital Out menu (press OUT on the remote) and try a lower compatible resolution, and let your TV scale for you.

The picture is too bright with HDR on! HDR is for use with Black Frame Insertion, or Scanlines and CRT Masks. if you do not intend to use these, we suggest you turn the HDR setting off.

The picture is too dark with scanlines! If you do not have HDR turned on, try that first. If you have Black Frame Insertion on, try turning that off. If neither option helps, then your TV may not have the sheer brightness to brute force enough brightness through the CRT effects.

This is way too complicated, is there an "easy mode"? We suggest looking at the Getting Started section in the wiki, but we also suggest you look into using Profiles for your use case. We hope using Profiles becomes intuitive for getting your desired picture to your display.

Compatibility Questions

Does the RT4K support Elgato? I heard RetroTINK doesn’t support Elgato. Older Elgato capture cards (typically the HD60 S and older) did not support older RetroTINK devices, such as the RT2X. As long as you feed the capture card a compatible resolution and leave the RT4K in triple buffer mode for maximum compatibility, Elgato capture cards will handle the its output just fine.

It doesn’t work with my 1080p capture card! The RetroTINK-4K outputs 4K by default. Try outputting 1080p or lower to see if there is a resolution constraint for your capture card.

Is there HDCP Support? The RT4K will activate an effect that will obscure video when it detects HDCP is active in your input signal. The RT4K itself does not circumvent HDCP.

Can I use GCVideo Lite cables with my RT4K? The cables do output a signal, but there are other concerns regarding these cables.

Is the TINK-4K worth it for consoles from the 8th generation (PS4 / Xbox One) and beyond? You may want to look into using the RT4K on a modern console for the following reasons:

• Sharply scaling a console's 1080p input to 4K.
• Adding black frame insertion to decrease motion blur.
• Applying custom post processing effects for retro games on emulators.
• Trying out post processing effects on modern games made with a retro style using built-in pre-scaling features.

Can I use the RT4K to scale my set top box? If the output is not HDCP encrypted, you should be able to use the RT4K to upscale the image. Be advised: the RT4K is designed to sharply scale the image to another resolution, so you may prefer your display’s scaling to the way the RT4K does it.

You may also want to implement some image processing to allow you to give a more retro look to your content.

Can I upscale VHS/DVD? Yes, there are settings made specifically for deinterlacing content from VHS and DVDs.

Is the TINK-4K compatible with MiSTER DV? If you use direct video with your MiSTER you can use the HDMI input directly into the RT4K.

Store/Pricing Questions

I want to buy two RT4K’s / How many can I buy? There is currently a limit of 1 per person for purchasing an RT4K unit.

Is the RT4K really $1,000? The RT4K currently retails for $750 directly from the RetroTINK store.

This is so expensive! The RT5X, RT2X, and RT2XSCART are still actively sold and supported, and will remain the flagship product for Mike Chi for the time being. Please look into those products for your upscaling needs.

Is there a coupon code for the RT4K? No, there are none and there are currently no plans to have one any time soon at the RetroTINK store.

When can I expect a price drop/sale? Black Friday? The Big Game? None of the RetroTINK products have ever gone down in price or gone on sale at the RetroTINK store. Unless there is a major change in the sourcing for the materials used, do not expect a cheaper price.

Is there a payment plan available? RetroTINK.com does not currently have any payment plans.

Can I buy a used RT4K? RetroTINK.com does not sell used or refurbished RT4K units.

I live in the UK and want a RetroTINK-4k! Please use the special UK checkout link to purchase a unit directly from the RetroTINK store.

8bitmods and GamesConnection currently only carry older RetroTINK Products, but there are plans to sell the RT4K in early 2024.

I don't live in the USA! How can I buy a RetroTINK-4k?? There are currently no international retailers for the RetroTINK-4K. The following stores do sell older RetroTINK products and will stock the RetroTINK-4K in early 2024.

International Resellers

	Store	Country
RetroStuff	Lillehammer	Canada
DragonBox Shop	Lillehammer	Germany
GamesConnection	Lillehammer	UK
BbitMods	Lillehammer	UK
Consoles4You	Lillehammer	Switzerland

I’d like to sell my RT5X to buy an RT4K! While that is your prerogative, if this is because you feel the RetroTINK-5X is obsolete, please know the RT5X is not at end of its life, and will be sold and supported for the foreseeable future.

Comparison Questions

My display does nearest neighbor upscaling, why would I need this? The RT4K gives you the flexibility to upscale any resolution to most other resolutions up to 4K in any method you prefer, with sub-frame latency. If your TV does nearest neighbor scaling with 720p then you are very much an outlier.

How does this compare to a CRT? CRTs have zero latency, whereas the RT4K will have sub-frame latency plus the latency of your display. While it is fast and near-zero, it is not zero like a CRT.

The RT4K does not support light guns the same way a CRT does.

A CRT is limited to its slot mask design, while the RT4K allows you to customize your slot masks and scanline effects by simply creating a custom image file.

How does this compare to the mClassic? The mClassic only outputs 1080p60, 1440p60 (if that's the native resolution of your display) or 4K30, while the RT4K can output up to 4K60.

The RT4K has a number of sharp and soft scaling algorithms that can be used to adjust the image to your liking.

How does this compare to the 4K Gamer Pro? The 4K Gamer Pro only processes 1080p signals and output them at 4K (other signals are simply passed through), while the RT4K can input and output almost any resolution.

Is this better than emulation? If you use well-shielded premium cables and video sources, the RT4K can be indistinguishable from emulation as long as you render the emulator at the same resolution as the source. The RT4K cannot help with how games render their graphics, so you may not get the expected results from early 3D consoles.

This doesn’t make my game look any better than on my TV Video game scalers do not change the internal rendering resolution of your console, which results in a very sharp upscale of a very low resolution picture. Premium scalers are made to lower input latency and add compatibility for older consoles.

Recommendation Questions

What's the best Capture Card to use with the RT4K? We recommend the Avermedia Live Gamer 4K GC573 for an internal capture card, as it allows for full RGB 4:4:4 capture at 4K60.

What's the best Best HDMI Splitter to use with the RT4K? For input, any HDMI 1.4 10Gbps splitter is suitable. For Output, any HDMI 2.1 18Gbps splitter is also suitable. As long as it doesn’t process the image there should be no additional latency.

What's the best best HDMI Switch to use with the RT4K? Any HDMI 1.4 switch rated at up to 10Gbps is suitable for the input. any HDMI 2.0 switch rated at up to 18Gbps is suitable for the output. As long as it doesn’t process the image there should be no additional latency.

What's the best HDMI Cable to use with the RT4K? Please use any certified HDMI 2.0 cable rated at 18Gbps.

Miscellaneous Questions

I want to use a scaler into the HDMI input port of the RT4K While this may seem like a good idea, doubling up on scalers is not recommended (including the RetroTINK-5X!). Doubling up on scalers may result in undesirable scaling or suboptimal sampling.

The RT4K supports inputs up to 1080p60 so it may work, but the ADC on the RT4K may be better than your current scaler.

I want to use the mClassic on the RT4K input! While it is not recommended, the RT4K will accept HDMI input up to 1080p60, which is the typical output of the mClassic.

I want to mClassic the output! While it is not recommended, please note the RT4K outputs 4K by default, while the mClassic only accepts up to 1080p as an input. You may need to change the RT4K’s output resolution to make it compatible.

I want to use 4K Gamer Pro on the RT4K output. This is unnecessary, as the RT4K already outputs 4K and allows for sharp scaling.

I lost the remote! Please purchase a new remote at the RetroTINK store.

Can I enable HDR on my input? This is possible, but your color mapping will not have any of the intended effects. The unit will work but you will see undesired colors. You should consider turning off HDR at your source and turning on HDR in the output menu.

If HDR from your console is important to you, consider using it directly to your display.

I lost my USB Cable! The included USB-C is actually not special in any way. You don’t even need data. As long as the cable can charge, you can use any USB-C cable with the RT4K.

Something is wrong with my unit! Please visit the RetroTINK Discord and ask for help in the RetroTINK-4K Help & Support Channel. You should be able to get help from somebody who may have had a similar problem previously.

I've checked the Discord channel and they were unable to help me / There is definitely something wrong with my unit after extensive testing! If you purchased your RetroTINK-4K at the RetroTINK store, please reply to your order confirmation email.

If you bought the unit from a partner store, please contact their support channels to see how they may help you.

RetroTINK-4K GUI Map

The GUI Map lists every single menu and menu item on the RetroTINK-4K, along with a brief description of what it does. For more information on them, click on a header to be taken to the appropriate section on this page.

GUI - Basic Setup

GUI - Input Selection

More information concerning inputs can be found in the Inputs section.

Digital Video
thing a	information
thing b	information

Front
Composite	Selects the front composite input.
S-Video	Selects the front s-video input.

Rear RCA
YPbPr	Selects the rear RCA YPbPr input.
RGsB	Selects the rear RCA RGsB input.
CVBS on Green	Selects the rear RCA CVBS input.

SCART
RGBS (75 ohm)	Selects the SCART input and sets it to RGBS
RGsB	Selects the SCART input and sets it to RGsB
YPbPr	Selects the SCART input and sets it to YPbPr
CVBS on Pin 20	information
CBVS on Green	information
Y/C on Pin 20/Red	information

HD-15
RGBHV	information
RGBS	information
RGsB	information
YPbPr	information
CBVS on Hsync	information
CBVS on Green	information
Y/C on Green/Red	information

GUI - HDMI™ Output

More information concerning outputs can be found in the Outputs section.

Transmitter
HDR	Enables "HDR10 [8-bit]"
Colorimetry	Lets you choose between "Auto", "Rec. 709", "Rec. 2020", "Adobe RGB" and "Display-P3". With HDR enabled, Rec. 2100 is also available via the "Auto" setting.
Sync Lock	Lets you choose between "Triple Buffer", "Gen 50.0 Hz (x1)" and "Frame 50.0 Hz (x1)".
VRR	Lets you choose between "Off" and "FreeSync".
Deep Color	Lets you choose between "Off" and "On". Exceeds the HDMI 2.1 bandwidth spec if used with 4K60 output.

Output Resolution
4K60	Sets the output to 3840x2160p at 60 frames per second
4K50	Sets the output to 3840x2160p at 50 frames per second
1080p60	Sets the output to 1920x1080p at 60 frames per second
1080p50	Sets the output to 1920x1080p at 50 frames per second
1080p100	Sets the output to 1920x1080p at 100 frames per second
1440p100	Sets the output to 2560x1440p at 100 frames per second
1080p120	Sets the output to 1920x1080p at 120 frames per second
1440p120	Sets the output to 2560x1440p at 120 frames per second
480p60	Sets the output to 640x480p at 60 frames per second

BFI Control
Strobe	information
Blur	information
LCD Saver	information

GUI - Profiles

Load Profile
Load From File	Loads a chosen profile from the "profile" folder on the SD card.
Load Default	Loads the Default Profile.

Save Profile
Save Current	Saves the current profile by overwriting the original file on the SD card.
Save As New	Saves the current profile as "New Profile #".

Assign Profile
Button 1	Sets a specified profile on the SD card to Button 1 on the remote.
Button 2	Sets a specified profile on the SD card to Button 2 on the remote.
Button 3	Sets a specified profile on the SD card to Button 3 on the remote.
Button 4	Sets a specified profile on the SD card to Button 4 on the remote.
Button 5	Sets a specified profile on the SD card to Button 5 on the remote.
Button 6	Sets a specified profile on the SD card to Button 6 on the remote.
Button 7	Sets a specified profile on the SD card to Button 7 on the remote.
Button 8	Sets a specified profile on the SD card to Button 8 on the remote.
Button 9	Sets a specified profile on the SD card to Button 9 on the remote.
Button 10	Sets a specified profile on the SD card to Button 10 on the remote.
Button 11	Sets a specified profile on the SD card to Button 11 on the remote.
Button 12	Sets a specified profile on the SD card to Button 12 on the remote.
Power Up	Sets a specified profile on the SD card to load when the RT4K is powered up.

GUI - Advanced Settings

GUI - Scaling/Cropping

Input Crop
Top Trim	Adjusts trim on the top edge of the picture.
Bottom Trim	Adjusts trim on the bottom edge of the picture.
Left Trim	Adjusts trim on the left edge of the picture.
Right Trim	Adjusts trim on the right sedge of the picture.
Vert. Pre-Scale	Reduces the effective vertical resolution of an HDMI image. Can be set between "1/2" and "1/31".
RoTATE (Beta)	information

CP Auto Crop
Vertical Only	Crops only the top and bottom edges of the image, sets Aspect Correction to "4:3 (PAR)" and Scaling Mode to "Proportional".
Full Crop to 4:3	Crops all edges of the image, sets Aspect Correction to "4:3 (PAR)" and Scaling Mode to "Proportional".
Full Crop to 16:9	Crops all edges of the image, sets Aspect Correction to "16:9 (PAR)" and Scaling Mode to "Proportional".

Scaler
Aspect Correction	Lets you choose between "4:3 (PAR)", "16:9 (PAR)" and "1:1 (Sq. Pixel)" options.
Scaling Mode	Lets you choose between "Auto Fill", "Proportional", "Free-Form" and "Auto Fill Integer" options.
Vert. Factor	Adjusts the vertical height of the image. Only available when Scaling Mode is set to "Proportional" or "Free-Form".
Hori. Factor	Adjusts the Horizontal width of the image. Only available when Scaling Mode is set to "Free-Form".

Buffer
Length	Displays the current lag in milliseconds. Can be set to "Min. Lag", "1/2 Frame" or "1 Frame".

Masking Color
Red	Adds red to the cropping mask, between 0 and 31.
Green	Adds green to the cropping mask, between 0 and 31.
Blue	Adds blue to the cropping mask, between 0 and 31.
Show	Lets you choose between "Cropping Only" and "Always".

Processing / Effects

Interpolation
Vert. Kernel	Lets you choose between "Bilinear Sharp", "Bilinear Med.", "Bilinear Std.", "Bilinear Soft", "Cubic", "Lanczos2", "Lanczos3", "Sinc", and "None".
Hori. Kernel	Lets you choose between "Bilinear Sharp", "Bilinear Med.", "Bilinear Std.", "Bilinear Soft", "Cubic", "Lanczos2", "Lanczos3", "Sinc", and "None".
Anti-Ringing	Can be set to "On" or "Off". Only visible on "Lanczos2" and "Lanczos 3".

Scanline
Function	Lets you choose between "Off", "Exponential", "Gaussian", "Super Gaussian", "Linear", "Box", "LCD Mono" and "LCD RGB". Anything except for "Off" will enable the settings below.
Strength	Increases scanline strength from 0 to 99.
Modulation	Increases modulation strength from 0 to 99.
Red Bleed	Enables red bleed.
Red Convergence	Adjusts red convergence from -10 to 10.
Blue Convergence	Adjusts blue convergence from -10 to 10.

Mask
Enable	Enables the Mask feature, as well as the Strength option. Will not appear to do anything until "Load from File" is used.
Strength	Adjusts the mask strength from -10 to 10.
Load from File	Select a Mask File from the "mask" folder on the SD card.

Horizontal Blur
Function	Lets you choose between "Off" and "IIR LPF", enabling the Cut-Off Freq option below.
Cut-Off Freq	Adjusts the blur strength from 0.50 MHz to 9.00 MHz, in 0.25 increments.

Color Correction

Gamma/PQ
Input Factor	Can be adjusted between 0.99 and 5.00.
Input Lift	Can be adjusted between -1.00 and 1.00.
Input Gain	Can be adjusted between 0.00 and 10.00.
Output Factor	Can be adjusted between 0.10 and 5.00.
SMPTE 2048 PQ	information

Color Space Conversion
Custom Matrix	Enables the Input RGB to XYZ options below.
Load from SD	Lets you load a CSC file from the "csc" folder on the SD card.

Input RGB to XYZ
Xo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Xo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Xo[Bin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Yo[Bin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Rin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Gin]	Can be adjusted between -1.75000 to +1.75000.
Zo[Bin]	Can be adjusted between -1.75000 to +1.75000.

Advanced Controls
Bit Crush	Lowers the color depth of the picture. Can be adjusted between "Off" and "7 bits Removed".
Saturation	Increases or decreases image saturation. can be adjusted between -1.00 and +1.00.
Transfer Function	Can be set to "sRGB 0.055", "Rec.601/709 0.099", "SMPTE 240M 0.1115" or "Gamma".

GUI - Black Frame Insertion

BFI Control
Strobe	information
Blur	information
LCD Saver	information

BFI Color
Blending Mode	Lets you choose between "Solid" and "Alpha".
Red	Adjusts Red, Green and Blue from 0 to 31.
Green	Adjusts Red, Green and Blue from 0 to 31.
Blue	Adjusts Red, Green and Blue from 0 to 31.

GUI - Deinterlacer / Film

Mode
Algorithm	Lets you choose between "Motion Adaptive", "Weave", "Bob", "Linear", "Blend", "CRT Simulation" and "LCD Blending".
Field Inversion	Reverses the fields of 480i signals. Can be set to "Off" or "On".

Motion Adaptive Settings
Sensitivity	Adjusts the sensitivity of the Motion Adaptive Deinterlacer. Can be set to "Low", "Medium", "High" and "Max". Higher settings result in a more solid image but with more weaving artifacts.
Noise Threshold	Adjusts the noise threshold, at the cost of weaving. Can be adjusted between 0 and 63.
Interpolator	Choose which field to prioritize. Can be set to "Average", "Bottom Field" and "Upper Field"
Detector	Can be set to "Zero-lag" or "Symmetric".

Bob Settings
Offset	Adjusts how far each field is shifted when using the "Bob" Algorithm. Can be set between -3 and +3.

Film Mode
Inverse Telecine	Enables a detector for "3:2" telecine (24fps content) and "2:2" telecline (30fps content).
Dejudder 24 Hz	Can be set to "Off" or "On".

Cadence Detection
Motion Digital	Can be set from 0 to 500.
Motion CP	Can be set from 0 to 500.
Motion SDP	Can be set from 0 to 500.
Threshold	Can be set from 0 to 500.

GUI - Acquisition

GUI - HDMI™ In Receiver

Input Decimation
Input Pixels	Can be set between "1 (Output: 1)" and "15 (Output: 1)".
Output Pixels	Can be set between 1 and 15.
Initial Phase	Can be set between "1 of X" and "X of X", where "X" what Input Pixels is set to.

Colorspace
4:2:2 Upsampler	Can be set to "Linear" or "Nearest".
Input Range	Can be set to "Auto", "RGB Lim.", "RGB Full", "YCbCr 601", "YCbCr 709", "XUYCC 601", "XUYCC 709", "YCbCR 601 (Full)" or "YCbCR 709 (Full)".

Misc.
A/DAC Mode	Can be set to "Off", "NTSC" or "PAL".

GUI - RGB / Component ADC

Sampling
Samples per Line	Manually set the sampling.
Decimation Factor	Can be set to between 2 and 16.
Decimation Phase	Value range matches the Decimation Factor.
Sub-Phase	Adjusts the Sub-Phase in 11.25 increments. Can be set as high as "348.75 deg"
Anti-Alias LPF	Can be set to "Auto (16MHz)", "9MHz (Strong)", "16 MHz (Med)", "35 MHz (Light)", "95 MHz (Min.)" and "Off".

Sync
SoG Threshold	Adjusts the Sync on Green Threshold in 11.29 increments. Can be set between "0.00 mV" and "327.42 mV".
Pre-coast	Can be set between 1 and 31.
Post-coast	Can be set between 1 and 31.
Slow-lock	Gives more time to lock onto Sync on Green. Can be set to "Off" or "On".

Gain
Pre-ADC	Adjusts the picture gain. Can be set between -0.7 and +0.8.
Red	Adds red to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.
Green	Adds green to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.
Blue	Adds blue to the picture, in increments of 0.008. Can be adjusted between 1.000 and 1.996.

Offset
Red	Can be set between -100 and +100.
Green	Can be set between -100 and +100.
Blue	Can be set between -100 and +100.

Auto Calibrate
Phase	Analyzes the picture to determine the Sub-Phase setting. Works best on detailed images with high contrast details.
Gain	Analyzes the picture to determine the Red, Green and Blue Phase settings. Works best on calibration screens like in the 240p Test Suite.

GUI - Sample Rate Detection

Control
Auto Dec. Factor	Can be set to "Off" or "On". Enables all other options in the Sample Rate Detection Menu
Auto Dec. Phase	Can be set to "Off" or "Auto".
ADC Sample Rate	Manually set the sampling.

Progressive Detection
Enable Sample Rate A	information
Enable Sample Rate B	information
Enable Sample Rate C	information
Enable Sample Rate D	information
Enable Sample Rate E	information
Enable Sample Rate F	information

Interlaced Detection
Enable Sample Rate A	information
Enable Sample Rate B	information
Enable Sample Rate C	information
Enable Sample Rate D	information
Enable Sample Rate E	information
Enable Sample Rate F	information

GUI - SDP Decoder

Gain / Balance
Brightness	information
Contrast	information
Chroma	information
Phase	information
Blue Only	information
Setup	information

Processing
Y/C Filter	information
Comb Bandwidth	information
Chroma Badwidth	information
Sharpness	information
CTIE	information

Sync
H-Lock Speed	information
Standard	information

GUI - Audio Input

Sampling
Sample Rate	Can be set to "48 kHz" or '96 kHz".
Pre-amp Gain	Can be set between "-24.0 dB" and "+28.0 dB" in 0.5 increments.

Source
Input Override	Manually changed the audio input to another source. Can be set to "Off", "RCA", "HD-15", "SCART", "Front" or "S/PDIF".
Input Swap	Can be set to "Mono (Left)", "Mono (Right" or "L/R Swap".

GUI - System

GUI - OSD / Firmware

On Screen Display
Position	Can be set to "Left", "Center" and "Right".
Auto-Off	Sets the time the menu will disable after inactivity. Can be set up to "100 sec" in 10 sec increments.
Load Banner	Loads a menu banner from the "image" folder on the SD card.
Enable Debug OSD	Permenantly displays one of the debug OSDs on the screen. Can be set to "Off", "Status Pg 1", "Status Pg 2", "Status Pg 3" or "Console".

Firmware Update
Check SD Card	Checks the SD card for update files stored in the SD card's root directory. If multiple firmware files are present, the most recent one will be chosen.

GUI - Device

GUI - Status

Status
Lets one display one of three System Status pages relating to the RT4K.

GUI - System Status Page 1

Video Source
Video Source	CP Proc. (I assume CP Proc will change based on selection)
Input Timing	information
Pixel Clock	information
Freq	information
Detected Mode	information

Audio Input
Audio Input	I2S (I assume will change based on audio input)
Measured Freq	information
Measured Freq	information
HDMI N / CTS	information

FPGA Core
Scaler Clock	information
PLL VCO	information
Pipeline	information
SDRAM Clock	information
SDRAM Load	information

HDMI Transmitter
Output Timing	information
Active Size	information
Pixel Clock	information
HDMI Standard	information

PIC32MX MCU
System Clock	information
Uptime	information
Loop Time	information
Last IR Code	information
SD Card Free	information

GUI - System Status Page 2

HDMI Input Protocol Analyzer
TMDS	information
Mode	information
Resolution	information
Colorspace	information
H. Timing	information
V. Timing (F0)	information
V. Timing (F1)	information
Audio	information
AVI Infoframe	information
Aud. Infoframe	information
VS Infoframe	information
ACP Infoframe	information

GUI - System Status Page 3

HDMI TX Information
TX Mode	information
Hot Plug	information
Scrambling	information
Clock Factor	information
Ch 0 Error	information
Ch 1 Error	information
Ch 2 Error	information
Sink EDID Dump	information

GUI - Diagnostic Console

to do

Diagnostic Console
Displays a diagnostic console screen regarding Digital In TX channels.

GUI - About

About
About	Displays the name of the device, the firmware version, and the Device ID.
Resorces	Displays the URLs for the RetroTINK website, Discord channel, and the RetroTINK-4K wiki page.
Thanks!	Displays a thank you message from Mike Chi to the user.