CRT:ADDS 4000

From ConsoleMods Wiki
Revision as of 01:44, 19 June 2022 by Derf (talk | contribs)
Jump to navigation Jump to search
ADDS 4000
ADDS 4000.png
Information
Manufacturer Boundless
Type Text Terminal
Size 14"
240p/480i No
480p No
720p No
1080i No
Vsync 60hz/71hz/82hz/100hz
Widescreen No
Dimensions Width: 318mm

Depth: 330mm

Height: 340mm
Weight 29 lbs
Links
Operation Manual ADDS 4000 User's Guide

ADDS 4000/110 User's Guide ADDS 4000/160 User's Guide ADDS 4000/260 User's Guide ADDS 4000/260 LF LFC User's Guide

Ethernet Adapter User's Guide

Text only terminal with a monochrome screen that comes in page-white, amber, or green colors. Compatible with PC101/102/106/107 or ANSI VT-220 keyboards via RJ11 connector on the left side.

Supported Terminal Emulators

The ADDS 4000 series is capable of emulating various terminals depending on model listed below[1].

Model Emulators Available
ADDS 4000/110 ADDS Viewpoint A1, A2, 3A, 3A+; Lear Siegler ADM 3A
ADDS 4000/150 ADDS Viewpoint and Regent 40; Wyse WY-50, WY-75, TeleVideo TVI-910, TVI-920,TVI-925; Hazeltine HZ-1500; DEC VT52, VT100; PCTerm
ADDS 60 ADDS Viewpoint, AT 386 (Unix console), DEC VT100, VT220, VT320, Wyse WY-50/50+ WY-60, TeleVideo TVI 925, PC Term, SCO Console, BBS ANSI, Wordperfect Graphics
ADDS 4000 ADDS Viewpoint and Regent 40; Wyse WY-50, WY-75, TeleVideo TVI-910, TVI-920,TVI-925; Hazeltine HZ-1500; DEC VT52, VT100; PCTerm, SCO Console
ADDS 4000/160 ADDS Viewpoint, ADDS Viewpoint 60, DEC VT100, VT220, VT320, VT420 PC TERM, Wyse WY-50/50+, WY-60 TeleVideo TVI 925, PC Term (925 PC)
ADDS 4000/260 ADDS Viewpoint, DEC VT100, VT220, VT320, Wyse WY-50/50+, WY-60 TeleVideo TVI 925, PC Term (925 PC), SCO console, AT 386 (UNIX console), WordPerfect graphics
ADDS 4000/260LF ADDS Viewpoint, AT 386 (Unix console) DEC VT100, VT220, VT320, Wyse WY-50/50+, WY-60, TeleVideo TVI 925, PC Term, SCO Console, WordPerfect graphics
ADDS 4000/260LFC Same as 4000/260LF plus WY-325, WY-350
ADDS C1099A HP 700/96 (factory default); Wyse WY-60, WY-50/50+, DEC VT320, VT220, VT100; ADDS Viewpoint, PCTerm (925 PC); TeleVideo TVI-925; SCO console, AT 386 (UNIX console)
ADDS 3153 IBM 3151, Wyse WY-60, WY-50/50+, DEC VT320, VT220, VT100; ADDS Viewpoint, PCTerm (925 PC); TeleVideo TVI-925; SCO console, AT 386 (UNIX console)
ADDS 3153 LF Same as ADDS 3153
VT510, VT520, VT525, Dorio 10 ADDS Viewpoint; DEC VT-100, VT220, VT320, Dorio 10; Wyse WY-50/50+ , WY-55, WY-60/160, WY-120/150; TeleVideo TVI 910+ , TVI 925/950; SCO Console

Connecting to Linux Machine

The easiest way to connect the terminal to a Linux machine — such as a Raspberry Pi — is to obtain a DB-25 male to DB-9 female null modem cable and a DB-9 male to USB adapter cable. You must get one labelled "null modem", as it is cross wired to be used without a modem.

Connect the cables to each other, one end to the terminal's EIA port (fastest), and the other to a USB port on your Linux host device.

Terminal Setup

  1. Press Ctrl + Scroll Lock (may be "PrLne" or "PrMsg" on your keyboard) to access Setup menu.
  2. Press F1 to enter Quick menu (if not already selected). Set the following:
    Host/Printer=EIA/None (enables EIA port to be connected to Linux host)
  3. Press F2 to enter General menu. Set the following:
    Emulation=VT100
    (and optional settings to turn down the bell noise and set a screen saver to protect the CRT)
  4. Press F3 to enter Display menu. Set the following:
    Display Cursor=On
    Page Length=24
    Screen Length=26
    Columns=80
  5. Press F4 to enter Keyboard menu. Set the following:
    Key Mode=ASCII
  6. Press F6 to enter Ports menu. Set the following:
    EIA Baud Rate=115200 (if not available, note the value you choose)
    EIA Xmt=Xon-Xoff
    EIA Data Format=8/1/N
    EIA Recv=Xany-Xoff(XPC)
    EIA Parity Check=Off
    EIA Xmt Pace=Baud
  7. Press F7 to enter Host menu. Set the following:
    Comm Mode=Full Duplex
  8. Press F9 to enter Emulation menu. Set the following:
    ANSI-ID=VT100 (this will identify the terminal as a VT100 terminal to Linux)
    Status Line=Off (recommended to prevent burn-in with line/text at top of screen)
  9. Press F13 (may be "Print" or "Print Screen" on your keyboard) to enter Exec menu.
    • Press Enter on "Save Terminal" and wait for "DONE" message.
    • Press Enter on "Save Session" and wait for "DONE" message.
  10. Press F14 (may be "Hold", "Break", or "Pause" on your keyboard) and Y to save and exit.

Linux Setup

  1. Enable the terminal console to be accessible by serial.
    • On a Raspberry Pi, this can be set by running sudo raspi-config and enabling the "Serial Port" option under Interface Options; or by running sudo vi /boot/config.txt and adding an [all] section at the bottom followed by enable_uart=1.
  2. Enable the USB serial port and set the baud rate to match the one you had set in the previous section.
  3. If a login prompt isn't shown on the physical terminal, reboot the physical terminal followed by the Linux machine and it should prompt you for a login on the physical terminal.

References