Master System:Video Output Notes: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
== French | == Mark III == | ||
The Sega Mark III is the original version of the Master System hardware and was the first Sega console to have a video output better than RF, featuring both composite and RGB output sent through an 8-pin DIN connector (specifically the 262 degree or "U-shape" variant). While the composite output is suitable for practically any display without external components, the RGB output is not, as it comes directly from the VDP and hence requires amplification. A cable with a built-in amplifier such as the French SCART cable (detailed in the section below) can be used, or the console itself can be modified with an internal amplifier, making it compatible with standard Master System and model 1 Genesis/Mega Drive RGB cables. | |||
== French Master System II == | |||
Unlike all other versions of the Sega Master System II, the French Master System II offers RGB output and was shipped with a special SCART cable. Unlike other French consoles that offered RGB converted from composite, RGB on the French SMS II is native RGB output directly from the VDP. However, because the RGB output comes straight from the VDP (much like the Mark III), it is not amplified and requires the SCART cable that came bundled with the console. This is because the SCART cable contains an amplifier circuit which makes this RGB output suitable for most displays. | |||
The French SMS II also does not output composite video as it does not contain a video encoder chip, and the DIN pin which normally carries this signal is unused. | |||
== Japanese Version (MK-2000) == | == Japanese Version (MK-2000) == | ||
The Japanese Master System (often referred to as the MK-2000) does not require any components on the CSYNC line. When connected to a display or processor, it will output around | The Japanese Master System (often referred to as the MK-2000) does not require any components on the CSYNC line. When connected to a display or processor, it will output around 350 mV without anything else needed. In fact, all four lines (red, green, blue and sync) all have the necessary components on the motherboard, so the RGB cable will just be a full pass-through cable. This is the opposite of all other SMS revisions, and using RGB cables meant for these consoles on the MK-2000 will result in a dimmer picture. | ||
== RGB Cable Components == | == RGB Cable Components == | ||
For | For all other SMS consoles with RGB output, all RGB cables that use CSYNC should have a 470 ohm resistor and a 10 uF–220 uF 10 V minimum capacitor with the positive leg facing the console on the sync line (pin 7). A 10 uF capacitor is all that's needed, but it is also very common for people to use 220 uF. Either way, the voltage rating shouldn't be below 10 V. Composite video can also be used for sync. The red, green and blue signals must have 75 ohm in-line resistors as the picture will be too bright and washed out without them. | ||
[[Category:Master System]] | |||
Revision as of 17:55, 20 October 2023
Mark III
The Sega Mark III is the original version of the Master System hardware and was the first Sega console to have a video output better than RF, featuring both composite and RGB output sent through an 8-pin DIN connector (specifically the 262 degree or "U-shape" variant). While the composite output is suitable for practically any display without external components, the RGB output is not, as it comes directly from the VDP and hence requires amplification. A cable with a built-in amplifier such as the French SCART cable (detailed in the section below) can be used, or the console itself can be modified with an internal amplifier, making it compatible with standard Master System and model 1 Genesis/Mega Drive RGB cables.
French Master System II
Unlike all other versions of the Sega Master System II, the French Master System II offers RGB output and was shipped with a special SCART cable. Unlike other French consoles that offered RGB converted from composite, RGB on the French SMS II is native RGB output directly from the VDP. However, because the RGB output comes straight from the VDP (much like the Mark III), it is not amplified and requires the SCART cable that came bundled with the console. This is because the SCART cable contains an amplifier circuit which makes this RGB output suitable for most displays.
The French SMS II also does not output composite video as it does not contain a video encoder chip, and the DIN pin which normally carries this signal is unused.
Japanese Version (MK-2000)
The Japanese Master System (often referred to as the MK-2000) does not require any components on the CSYNC line. When connected to a display or processor, it will output around 350 mV without anything else needed. In fact, all four lines (red, green, blue and sync) all have the necessary components on the motherboard, so the RGB cable will just be a full pass-through cable. This is the opposite of all other SMS revisions, and using RGB cables meant for these consoles on the MK-2000 will result in a dimmer picture.
RGB Cable Components
For all other SMS consoles with RGB output, all RGB cables that use CSYNC should have a 470 ohm resistor and a 10 uF–220 uF 10 V minimum capacitor with the positive leg facing the console on the sync line (pin 7). A 10 uF capacitor is all that's needed, but it is also very common for people to use 220 uF. Either way, the voltage rating shouldn't be below 10 V. Composite video can also be used for sync. The red, green and blue signals must have 75 ohm in-line resistors as the picture will be too bright and washed out without them.