NES:Famicom Disk System Glitching Sprites Fix: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 1: Line 1:
Certain combinations of Famicom and Famicom Disk System (FDS) RAM adapter units have an issue which causes sprites to appear glitchy due to interference on the FDS RAM cart pins. The issue seems to affect mostly Famicoms made in 1989 and RAM adapters with boards marked "HVC-FMR-03" and some early "HVC-FMR-02" boards. Information for this guide was compiled from multiple sources.<ref>https://retro.supermegabyte.com/2018/07/23/fix-glitchy-famicom-disk-system-sprites/</ref><ref>https://www.famicomworld.com/forum/index.php?topic=10607.0</ref><ref>https://synt4x.org/blog/index.php/2018/01/19/glitchy-graphics-on-famicom-disk-system/</ref><ref>https://twitter.com/SuperZvesda/status/1639694888944951297</ref>
Certain combinations of Famicom and Famicom Disk System (FDS) RAM adapter units have an issue which causes sprites to appear glitchy due to interference on the FDS RAM cart pins. The issue seems to affect mostly Famicoms made in 1989 and RAM adapters with boards marked "HVC-FMR-03" and some early "HVC-FMR-02" boards. Information for this guide was compiled from multiple sources.<ref>https://retro.supermegabyte.com/2018/07/23/fix-glitchy-famicom-disk-system-sprites/</ref><ref>https://www.famicomworld.com/forum/index.php?topic=10607.0</ref><ref>https://synt4x.org/blog/index.php/2018/01/19/glitchy-graphics-on-famicom-disk-system/</ref><ref>https://twitter.com/SuperZvesda/status/1639694888944951297</ref>


<div class="inline-thumb">
<div class="inline-thumb">[[File:FDS Glitching Sprites Before.png|thumb|Sprite issue affecting Mario.]] [[File:FDS Glitching Sprites After.png|thumb|After sprite issue fix.]]</div>
[[File:FDS Glitching Sprites Before.png|thumb|Sprite issue affecting Mario.]] [[File:FDS Glitching Sprites After.png|thumb|After sprite issue fix.]]
</div>
{{br}}
{{br}}


Line 9: Line 7:


The solution is to add resistors on the data pins of the FDS RAM cart unit, which fixes the interference.
The solution is to add resistors on the data pins of the FDS RAM cart unit, which fixes the interference.
[[File:FDS Glitching Sprites Fix.png|thumb|Fully installed fix.]]


# Obtain a [https://www.arcadepartsandrepair.com/store/components/resistors/4-7k-ohm-resistor-network-9-pin-bussed-r1105/ 9-pin 4.7kohm resistor array].
# Obtain a [https://www.arcadepartsandrepair.com/store/components/resistors/4-7k-ohm-resistor-network-9-pin-bussed-r1105/ 9-pin 4.7kohm resistor array].
#* Alternatively, you can use eight 4.7kohm resistors.
#* Alternatively, you can use eight 4.7kohm resistors and solder one end together.
# Use electrical tape to line up the resistor array as shown and hold it in place.
# Use electrical tape to line up the resistor array as shown below and hold it in place.
#: [[File:FDS Glitching Sprites Fix.png|400px]]
# Bend the first pin of the resistor array upwards so that it doesn't make contact with anything on the board.  
# Bend the first pin of the resistor array upwards so that it doesn't make contact with anything on the board.  
# Solder a wire between the first pin and ground. Example ground point shown in image to the right.
# Solder a wire between the first pin and ground. Example ground point shown in image above.
# Solder pin 2 of the resistor array to pin 6 of the FDS RAM adapter.
# Solder pin 2 of the resistor array to pin 6 of the FDS RAM adapter.
# Solder the remaining pins of the resistor array to the FDS RAM adapter pins. Pins 6-13 should all be soldered to.
# Solder the remaining pins of the resistor array to the FDS RAM adapter pins. Pins 6-13 should all be connected to the resistor array.


{{br}}
{{br}}


== References ==
== References ==

Revision as of 15:50, 26 March 2023

Certain combinations of Famicom and Famicom Disk System (FDS) RAM adapter units have an issue which causes sprites to appear glitchy due to interference on the FDS RAM cart pins. The issue seems to affect mostly Famicoms made in 1989 and RAM adapters with boards marked "HVC-FMR-03" and some early "HVC-FMR-02" boards. Information for this guide was compiled from multiple sources.[1][2][3][4]

Sprite issue affecting Mario.
After sprite issue fix.


Solution

The solution is to add resistors on the data pins of the FDS RAM cart unit, which fixes the interference.

  1. Obtain a 9-pin 4.7kohm resistor array.
    • Alternatively, you can use eight 4.7kohm resistors and solder one end together.
  2. Use electrical tape to line up the resistor array as shown below and hold it in place.
    FDS Glitching Sprites Fix.png
  3. Bend the first pin of the resistor array upwards so that it doesn't make contact with anything on the board.
  4. Solder a wire between the first pin and ground. Example ground point shown in image above.
  5. Solder pin 2 of the resistor array to pin 6 of the FDS RAM adapter.
  6. Solder the remaining pins of the resistor array to the FDS RAM adapter pins. Pins 6-13 should all be connected to the resistor array.


References