Neo Geo:Battery Replacement: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
The original battery in a Neo Geo MVS is a rechargeable coin-cell battery that is soldered in. Over time, these degrade and leak onto the board. You have the option to replace the battery stand and holder with one that can be swapped by hand. Note that you can either replace the battery with a modern rechargeable one, such as an LIR2032 or ML2032, or (with some extra desoldering work) replace it with a non-rechargeable one.
The original battery in a Neo Geo MVS is a rechargeable coin-cell battery that is soldered in. Over time, these degrade and leak onto the board. You have the option to replace the battery stand and holder with one that can be swapped by hand. Note that you can either replace the battery with a modern rechargeable one, such as an LIR2032 or ML2032, or (with some extra desoldering work) replace it with a non-rechargeable one.


{{Note|Replacing the battery likely will wipe your backup RAM and all stored hiscores. You may wish to back these up to a memory card or supply 3V to BATVCC to retain this memory.}}
It's worth noting that the MVS can run without a battery, but you will lose all backup RAM and clock settings every time it is powered off.
 
{{Note|Replacing the battery likely will wipe your backup RAM, all soft-DIP settings, and all stored hiscores. You may wish to back these up to a memory card or supply 3V to BATVCC to retain this memory.}}


== Replacing the Battery Holder ==
== Replacing the Battery Holder ==
This guide assumes your battery holder replacement kit is a small PCB, a metal battery holder, and L-shaped metal pins.
This guide assumes your battery holder replacement kit is a small PCB, a metal battery holder, and L-shaped metal pins. This includes the "Neo Jamma Batt v1.0".


# Check underneath the board in the battery area to see if there is a foam pad there. If so, remove enough of the pad that the bottom-side of the three battery pads are visible.
# Check underneath the board in the battery area to see if there is a foam pad there. If so, remove enough of the pad that the bottom-side of the three battery pads are visible.
Line 14: Line 16:
# Solder the three pins and clip off the excess.
# Solder the three pins and clip off the excess.
# If using a rechargeable battery, insert it into the new battery holder, positive side toward the "+" sign on the metal battery holder. If using non-rechargeable batteries, follow the steps in the next section.
# If using a rechargeable battery, insert it into the new battery holder, positive side toward the "+" sign on the metal battery holder. If using non-rechargeable batteries, follow the steps in the next section.
<gallery>
Neo JAMMA Batt v1.0 1.jpg
Neo JAMMA Batt v1.0 2.jpg
Neo JAMMA Batt v1.0 3.jpg
</gallery>


== Disabling the Recharging Circuit ==
== Disabling the Recharging Circuit ==

Latest revision as of 15:00, 26 February 2024

The original battery in a Neo Geo MVS is a rechargeable coin-cell battery that is soldered in. Over time, these degrade and leak onto the board. You have the option to replace the battery stand and holder with one that can be swapped by hand. Note that you can either replace the battery with a modern rechargeable one, such as an LIR2032 or ML2032, or (with some extra desoldering work) replace it with a non-rechargeable one.

It's worth noting that the MVS can run without a battery, but you will lose all backup RAM and clock settings every time it is powered off.

Exclamation-circle-fill.svgReplacing the battery likely will wipe your backup RAM, all soft-DIP settings, and all stored hiscores. You may wish to back these up to a memory card or supply 3V to BATVCC to retain this memory.


Replacing the Battery Holder

This guide assumes your battery holder replacement kit is a small PCB, a metal battery holder, and L-shaped metal pins. This includes the "Neo Jamma Batt v1.0".

  1. Check underneath the board in the battery area to see if there is a foam pad there. If so, remove enough of the pad that the bottom-side of the three battery pads are visible.
  2. Desolder the existing battery. It is easiest to first heat the middle pin and bend the battery so the middle pin is freed, then heat both of the other legs. Fully remove the solder from the three holes.
  3. Clean up the area and the same area underneath the board with isopropyl alcohol in case the battery leaked.
  4. Add just enough solder to cover the middle pad of the PCB. This will ensure a good connection with the battery.
  5. Solder the battery holder onto the PCB. The "+" sign should be closest to the square part of the PCB.
  6. Insert the L-shaped pins into the PCB and carefully lower the PCB onto the board so that the pins insert into the holes.
  7. Solder the three pins and clip off the excess.
  8. If using a rechargeable battery, insert it into the new battery holder, positive side toward the "+" sign on the metal battery holder. If using non-rechargeable batteries, follow the steps in the next section.

Disabling the Recharging Circuit

This process is only applicable if you are using non-rechargeable batteries.

Instructions for each model provided on the Jamma Nation X website.