Neo Geo:RGB Bypass Mod (AES): Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
No edit summary

Revision as of 23:29, 24 April 2023

This page will show you a "basic" bypass for the Neo Geo AES console that eliminates the Sony CXA amp and sends video (at the proper voltage) directly from the NG's digital-to-analog-converter, to the multi-out. This was tested on the worst video output revision of the Neo Geo (3-6), however, it should work on other revisions. It's been long discussed that some Neo Geo units output better RGB video than others. While that's true, all AES' can have a fairly simple RGB bypass performed that gets the best out of the built-in DAC. That means you can make every revision AES look identical, regardless of serial number, including and especially the notorious 3-6 revision motherboard.

Exclamation-triangle-fill.svgThis mod will disable composite video!


Tools Needed

  • Basic soldering skills
  • Soldering iron, wire, heatshrink tubing
  • 150 Ohm resistors
  • Desoldering gun not necessary, but might make it easier

Disassembly

  1. Remove the screws on the bottom of the AES. There are three under the marked footpads in the image below. Please note that the screws are different sizes, so make sure to mark where each goes!
    NeoGeoAES3-6 Bottom.jpg
    • Unfortunately, due to the age of these footpads, they'll most likely break. If you get lucky, you can peel them back just enough to get your screwdriver in, but expect to accidentally break at least one:
    NeoGeoAES3-6 Footpads.jpg
  2. After removing the top plastic cover, remove the following screws from the motherboard.
    NeoGeoAES3-6 MotherboardScrews-1024x767.jpg
  3. Remove the reset button and power switch, then carefully lift the motherboard out of the bottom case.

RGB Bypass

  1. Now you'll need to remove six components located in the top-left of the motherboard, next to the A/V out port: three resistors and three capacitors. The ideal way to remove them is with a desoldering gun, however if you're careful, you can use a soldering iron and some tweezers, or even gently snip them out with flush cutters. The area should look like the picture on the right when finished.
    NeoGeoAES3-6 TopMotherboard-1024x787.jpg NeoGeoAES3-6 RemoveRGBcomponents-1024x817.jpg NeoGeoAES3-6 RemovedRGBcomponents-1024x737.jpg
  2. Flip the motherboard over and locate the area near the A/V Multi-out in the upper right of this picture:
    NeoGeoAES3-6 MotherboardBottom-1024x748.jpg
  3. You'll need to connect each of the following points with a 150Ohm resistor, no wire required with the following technique:
    1. Starting with the #1 resistor in the above picture (as that's the only one that needs a bend in the routing), solder one end of the resistor to one of the lower points.
    2. Measure and position the resistor with the connection points on the multi-out (top pins) and trim to size.
    3. Add heatshrink tubing.
    4. Solder the top connection in place.
    5. Add some heat to shrink the tubing down for a nice connection.
      NeoGeoAES3-6 RGBpointsBefore-1024x801.jpg NeoGeoAES3-6 RGBpointsAfter-1024x740.jpg

Sync Isolation

Exclamation-circle-fill.svgThis mod may not be needed at all on other revision AES consoles. Technically, this isn't "needed" on the 3-6 units either, but it's strongly recommended to do it. You'll get a cleaner signal at a better voltage.


  1. Connect a wire to the bottom of pin 11 (CSYNC-out) of the Sony CXA. Run that wire through one of the existing holes of a capacitor you previously removed. DO NOT SOLDER TO THE HOLE, simply push the wire through to the other side!
    NeoGeoAES3-6 CXAsync-1024x596.jpg
  2. Carefully snip the positive input leg of the following capacitor and carefully rotate it. If you have a desoldering iron, it would be much better to desolder the whole cap, rotate it and solder the negative side back in place:
    NeoGeoAES3-6 CompositeVideoCap-1024x599.jpg
  3. Lastly, solder the wire that you ran through the hole, to the positive input side of the capacitor you just rotated. Then snip any excess.
    NeoGeoAES3-6 CompositeVideoCapCsync-1024x635.jpg