SNES:SNES Jr Pre-Assembled S-RGB Mod: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 1: Line 1:
[[Category:RetroRGB Migration]]
[[Category:RetroRGB Migration WIP]] Mitch1256
[[File:VoultarSRGBboardV2.jpg]]
[[File:VoultarSRGBboardV2.jpg]]



Revision as of 22:43, 12 June 2022

Mitch1256

VoultarSRGBboardV2.jpg

This guide shows you how to enable RGB and S-Video output on a SNES Mini / Jr using its built-in RGB amp (the 'S-RGB' chip). This method requires a custom board that connects all the components.  If you plan on using the S-RGB Encoder, this is definitely the method recommended.

Parts required: Voultar's Custom S-RGB Board

You'll need a few tools for this mod (more info on the tools can be found in [tools.html the tools section]):
The S-RGB connection board linked above
Soldering skills!
SNES RGB cable
The 4.5mm tool that opens the SNES
Philips head screwdriver
Soldering iron / solder
Thin gauge wire
Flux (or a flux pen) will make installation easier, but is not necessary.

RGB Mod:

The mod is pretty easy, however soldering to the S-RGB chip can be extremely challenging. It's recommended beginners use an amp bypass mod for ease of installation, however if you're willing to solder to the small points this will work perfectly:

Remove the 4 screws holding the plastic cover on using the 4.5mm tool. Then remove the 7 screws holding the motherboard in place (so, basically, just unbolt everything). Finally, unbolt the three screws holding the heatsink and find the S-RGB chip:
SNESMiniRGBModPage02.jpg
Solder six wires to the pins on the “S-RGB A” chip as shown below. A few tips: These are extremely small pins and very difficult for people who aren't experienced at soldering to work on. Use a soldering tip that's extremely thin, as well as very thin solder. Make sure to "tin" each pin and each wire before trying to solder them together.  it's also recommended to add flux to each of the pins before tinning, as it makes soldering to them much easier:
S-RGB RGBsYC.jpg
It's recommended to use heatshrink tubing to keep the wires together and also protect them from touching any other components. Then, replace the heaksink and run the cables through the hole pictured below on the left:
S-RGB WireRun.jpg
It's suggested to add non-conductive tape to the bottom of the circuit board:
SNES Mod Tape.jpg
Next, prepare to mount the circuit board over the multi-out pins.  You may notice that there's a few larger components sticking up.  If so, it's okay to snip them.  Also, some SNES Mini's come from the factory with the two ground pins soldered together. If your system has this, you could either cut the solder in the middle (be really careful not to damage the pins), or use a solder-removing method (de-soldering iron, solder wick, etc):
SNESMiniMultiOutInterference.jpg
SNES Multi-out Component Interference.jpg
Then, place the board over the multi-out connections and solder the multi-out pins to the board.  Then solder wires from the bottom RGB pads to the via's (holes) marked below - Flux will make soldering to those holes MUCH easier (click for full-sized):
SNES S-RGBboard InstallPoints.jpg
Finally, cut the RGBs / YC cables to size and solder them to the corresponding pins on the board.  Its' preferred to use heat shrink tubing to keep them all in place:
SNES S-RGBboard Installed.jpg
Then just bolt everything back together and give it a try!

Results:

A pretty easy mod and the picture quality is amazing!!! Check out the difference from an average SNES 1 to a SNES Mini:
SNS-CPU-GPM-02vsSNESMini.png