Xbox 360:RGH/RGH1.2: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
(update info for rgh1.2v2)
Line 1: Line 1:
[[Category:Xbox360]]
[[Category:Xbox360]]
RGH1.2 combines RGH1-like PLL slowdown with RGH2 software to allow reliable glitching of Phat consoles after 14699 dashboard.
RGH1.2 combines RGH1-like PLL slowdown with Glitch2 images to allow reliable glitching of Falcon/Jasper consoles with split CB (post 14699 kernel). RGH1.2 v2 ports this hack to Trinity/Corona consoles as well as fixing a few issues on Jaspers.


==Equipment Needed==
==Equipment Needed==
Line 7: Line 7:
** Coolrunner Rev A/B/C/D or CR3 Lite  
** Coolrunner Rev A/B/C/D or CR3 Lite  
** Matrix Glitcher  
** Matrix Glitcher  
** Squirt 360
** Squirt BGA/Reloaded
** X360ACE (All versions supported)
** X360ACE V1/V2/V3
** X360ACE V4/V5/V3+ (Trinity/Corona only)
** DGX
* A PC running Windows Vista or later  
* A PC running Windows Vista or later  
* A soldering iron, solder, and flux (MG 835 recommended)  
* A soldering iron, solder, and flux (MG 835 recommended)  
Line 20: Line 22:
===Falcon / Jasper===
===Falcon / Jasper===


====[https://web.archive.org/web/20160118143255im_/http://s15.postimg.org/avcw9muuj/coolrunnerrevcrgh12.jpg CoolRunner rev C/D]====
====[https://web.archive.org/web/20160118143255im_/http://s15.postimg.org/avcw9muuj/coolrunnerrevcrgh12.jpg Coolrunner Rev A/B/C/D]====
* A - PLL
* A - PLL
* B - STBY_CLK (only if not using oscillator)
* B - STBY_CLK (only if not using oscillator)
Line 26: Line 28:
* D - RST
* D - RST


====[https://web.archive.org/web/20161015093429im_/https://s1.postimg.org/p2lvareov/cr3litergh12.jpg CoolRunner 3 Lite]====
====[https://web.archive.org/web/20161015093429im_/https://s1.postimg.org/p2lvareov/cr3litergh12.jpg CR3 Lite]====
* A - PLL
* A - PLL
* B - STBY_CLK (only if not using oscillator)
* B - STBY_CLK (only if not using oscillator)
Line 38: Line 40:
* F - PLL
* F - PLL


====[https://web.archive.org/web/20160118143256im_/http://s12.postimg.org/77xf0z52l/squirtrgh12installdiagram.jpg Squirt 360]====
====[https://web.archive.org/web/20160118143256im_/http://s12.postimg.org/77xf0z52l/squirtrgh12installdiagram.jpg Squirt]====
* Squirt BGA 1.2: Disable the onboard 670pf and/or 480pf caps by removing R7 and R8
* Squirt Reloaded 2.X: remove R2 and connect STBY_CLK
* Pinout follows written labels
* Pinout follows written labels
* Don't use POST or RST tuners
* Don't use POST or RST tuners


====[https://web.archive.org/web/20161015093417im_/https://s4.postimg.org/gtnd5nknx/x360acergh12phatinstalldiagram.png X360ACE]====
====[https://web.archive.org/web/20161015093417im_/https://s4.postimg.org/gtnd5nknx/x360acergh12phatinstalldiagram.png X360ACE (V1/V2/V3), DGX]====
* C - POST
* C - POST
* D - RST
* D - RST
* F - PLL (22K ohm resistor required)
* F - PLL (22K ohm resistor required)
* Needs removal of a diode on the chip itself.
* Needs removal of a diode on the chip in order to set the voltage for the Phat CPU.


===Trinity / Corona===
===Trinity / Corona===
Line 52: Line 56:
====[[:File:RGH1.2_Slim_PLL.jpg|Close-up of PLL]]====
====[[:File:RGH1.2_Slim_PLL.jpg|Close-up of PLL]]====


====CoolRunner rev C/D====
====Coolrunner Rev A/B/C/D====
* B - STBY_CLK (only if not using oscillator)
* B - STBY_CLK (only if not using oscillator)
* C - POST
* C - POST
Line 58: Line 62:
* E - PLL (10K ohm resistor recommended)
* E - PLL (10K ohm resistor recommended)


====CoolRunner 3 Lite====
====CR3 Lite====
* B - STBY_CLK (only if not using oscillator)
* B - STBY_CLK (only if not using oscillator)
* C - POST
* C - POST
Line 75: Line 79:
* E - PLL (10K ohm resistor recommended)
* E - PLL (10K ohm resistor recommended)


====X360ACE====
====X360ACE (V1/V2/V3/V3+), DGX====
* C - POST
* C - POST
* D - RST
* D - RST
* F - PLL (10K ohm resistor recommended)
* F - PLL (10K ohm resistor recommended)


====DGX====
====X360ACE V4/V5====
* C - POST
* A - RST
* D - RST
* B - POST
* F - PLL (10K ohm resistor recommended)
* C1 - CPU_CLK_DP
* C2 - CPU_CLK_DN
* D - PLL (10K ohm resistor required)


====X360 Squirt====
====Squirt====
* Squirt Reloaded 2.X: remove R2 and connect STBY_CLK or remove 100 MHz and add 48 MHz oscillator
* Use SCL pad for PLL
* Use SCL pad for PLL
* Pinout follows written labels
* Pinout follows written labels
Line 98: Line 105:
# Click "Program". When complete, unplug the cable from the glitch chip.  
# Click "Program". When complete, unplug the cable from the glitch chip.  
#* Coolrunner: Set the switch back to "NOR".
#* Coolrunner: Set the switch back to "NOR".
====X360ACE V4/V5/V3+====
* xFlasher or other Gowin compatible programmer required in order to program these chips
* [[Xbox_360:Programming_Gowin-based_X360ACE_Chips|Programming Instructions]]


==Decrypting the NAND==
==Decrypting the NAND==

Revision as of 20:15, 15 May 2022

RGH1.2 combines RGH1-like PLL slowdown with Glitch2 images to allow reliable glitching of Falcon/Jasper consoles with split CB (post 14699 kernel). RGH1.2 v2 ports this hack to Trinity/Corona consoles as well as fixing a few issues on Jaspers.

Equipment Needed

  • A glitch chip:
    • Coolrunner Rev A/B/C/D or CR3 Lite
    • Matrix Glitcher
    • Squirt BGA/Reloaded
    • X360ACE V1/V2/V3
    • X360ACE V4/V5/V3+ (Trinity/Corona only)
    • DGX
  • A PC running Windows Vista or later
  • A soldering iron, solder, and flux (MG 835 recommended)
  • Isopropyl alcohol (91% or higher recommended) and cotton swabs
  • xFlasher 360, NAND-X, JR-Programmer, or Matrix Flasher
  • J-Runner with Extras (Includes RGH1.2 v2 Matrix/Coolrunner Timings)
  • RGH1.2 v2 Timing Files (X360ACE/Squirt chips only)

Glitch Chip Installation

Falcon / Jasper

Coolrunner Rev A/B/C/D

  • A - PLL
  • B - STBY_CLK (only if not using oscillator)
  • C - POST
  • D - RST

CR3 Lite

  • A - PLL
  • B - STBY_CLK (only if not using oscillator)
  • C - POST
  • D - RST

Matrix Glitcher

  • A - RST
  • B - POST
  • C - STBY_CLK (only if not using oscillator)
  • F - PLL

Squirt

  • Squirt BGA 1.2: Disable the onboard 670pf and/or 480pf caps by removing R7 and R8
  • Squirt Reloaded 2.X: remove R2 and connect STBY_CLK
  • Pinout follows written labels
  • Don't use POST or RST tuners

X360ACE (V1/V2/V3), DGX

  • C - POST
  • D - RST
  • F - PLL (22K ohm resistor required)
  • Needs removal of a diode on the chip in order to set the voltage for the Phat CPU.

Trinity / Corona

Close-up of PLL

Coolrunner Rev A/B/C/D

  • B - STBY_CLK (only if not using oscillator)
  • C - POST
  • D - RST
  • E - PLL (10K ohm resistor recommended)

CR3 Lite

  • B - STBY_CLK (only if not using oscillator)
  • C - POST
  • D - RST
  • E - PLL (10K ohm resistor recommended)

Matrix Glitcher (Corona)

  • A - RST
  • B - POST
  • E - PLL (10K ohm resistor recommended)

Matrix Glitcher (Trinity)

  • A - RST
  • B - POST
  • C - STBY_CLK
  • E - PLL (10K ohm resistor recommended)

X360ACE (V1/V2/V3/V3+), DGX

  • C - POST
  • D - RST
  • F - PLL (10K ohm resistor recommended)

X360ACE V4/V5

  • A - RST
  • B - POST
  • C1 - CPU_CLK_DP
  • C2 - CPU_CLK_DN
  • D - PLL (10K ohm resistor required)

Squirt

  • Squirt Reloaded 2.X: remove R2 and connect STBY_CLK or remove 100 MHz and add 48 MHz oscillator
  • Use SCL pad for PLL
  • Pinout follows written labels
  • Don't use POST or RST tuners

Programming the Glitch Chip

  1. Plug the cable from your programmer into the chip programmer.
    • If you are using an xFlasher, ensure the switch is set to SPI.
    • CoolRunner: Slide switch to "PRG".
  2. Open J-Runner with Extras. Click "Program Timing File" in the upper left and select your console’s tab and the relevant radio button for RGH 1.2.
  3. Click "Program". When complete, unplug the cable from the glitch chip.
    • Coolrunner: Set the switch back to "NOR".

X360ACE V4/V5/V3+

Decrypting the NAND

  1. Connect Ethernet and power on the console. The Coolrunner should blink once or more times, and then the console should start into XeLL RELOADED.
  2. Once XeLL finishes, it will display your CPU key and some other info. There is also an IP address.
  3. Enter the IP address into the box on the lower right of J-Runner and click "Get CPU Key". J-Runner will pull the info from the box, and decrypt the NANDs automatically.

Writing New NAND Image

  1. Power down the console, and connect your programmer to the motherboard.
    • If you are using an xFlasher, ensure the switch is set to SPI.
  2. In the upper right of J-Runner, ensure the Glitch2 radio button is selected.
  3. Click "Create XeBuild Image". This will take a few moments.
  4. Click "Write NAND".
  5. Disconnect your programmer when the process completes.
  6. Boot the console several times and ensure it boots consistently. If not, make sure your wiring is clean and neat and avoids noisy area. Run the wires near the X-Clamps for best results.
  7. Return to the RGH main page and continue in the Cleaning Up section.
Retrieved from "https://consolemods.org/wiki/index.php?title=Xbox_360:RGH/RGH1.2&oldid=10910"