Xbox 360:RGH/RGH3: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
Line 9: Line 9:
**[[Recommended Soldering Equipment|Specific recommendatons can be found on this page]]
**[[Recommended Soldering Equipment|Specific recommendatons can be found on this page]]
*28-30AWG Wire (Solid core recommended)
*28-30AWG Wire (Solid core recommended)
*An SMD or through hole resistor '''(Required on Phat)'''
*An SMD or through hole ('''Required on Phat''', optional on Slim)
**Falcon/Jasper: 22K Ohm (Red, Red, Orange, Yellow)
**Falcon/Jasper: 22K Ohm (Red, Red, Orange, Yellow)
**Trinity: 3K-10K Ohm (10K resistor color values are Brown, Black, Red, Gold)
**Trinity: 3K-10K Ohm  
***10K resistor color values are Brown, Black, Red, Gold
***Some Trinity consoles can occassionally have issues with RGH3 when using a high Ohm resistor, so it's best to start with around 3K if using one.
**Corona: 1K Ohm (Optional, Brown, Black, Red, Gold)
**Corona: 1K Ohm (Optional, Brown, Black, Red, Gold)
*1N4148 diode (Only Falcon/Jasper, '''highly recommended''')
*1N4148 diode (Only Falcon/Jasper, '''highly recommended''')
*Wire Insulation (kapton tape, electrical tape, heatshrink, etc.) for through hole resistors/diodes
*Wire Insulation (kapton tape, electrical tape, heatshrink, etc.) if using a through hole resistor/diode
*A PC running Windows Vista or later
*A PC running Windows Vista or later
*[https://github.com/Octal450/J-Runner-with-Extras J-Runner with Extras]
*[https://github.com/Octal450/J-Runner-with-Extras J-Runner with Extras]

Revision as of 00:01, 21 September 2023

RGH 3 is a modern method of the Reset Glitch Hack that uses the SMC in the Xbox 360's southbridge instead of a glitch chip in order to boot unsigned code.

MrMario2011 has video guides for RGH 3 on Falcon/Jasper[1], Trinity[2], and Corona [3] motherboards respectively. The guides from Larvs on Xbox 360 Hub[4] and BeefyDJ on Se7enSins[5] are also great resources for RGH 3 tutorials.

Exclamation-circle-fill.svgPhat consoles tend to be more stubborn with RGH3, and may have inconsistant booting behavior. It is recommended to use RGH 1.2 on a phat system, as it will be more stable.


Equipment Needed

  • A soldering iron, solder, flux, and Isopropyl alcohol with cotton swabs
  • 28-30AWG Wire (Solid core recommended)
  • An SMD or through hole (Required on Phat, optional on Slim)
    • Falcon/Jasper: 22K Ohm (Red, Red, Orange, Yellow)
    • Trinity: 3K-10K Ohm
      • 10K resistor color values are Brown, Black, Red, Gold
      • Some Trinity consoles can occassionally have issues with RGH3 when using a high Ohm resistor, so it's best to start with around 3K if using one.
    • Corona: 1K Ohm (Optional, Brown, Black, Red, Gold)
  • 1N4148 diode (Only Falcon/Jasper, highly recommended)
  • Wire Insulation (kapton tape, electrical tape, heatshrink, etc.) if using a through hole resistor/diode
  • A PC running Windows Vista or later
  • J-Runner with Extras
  • Any compatible NAND Programmer (Listed in the NAND backup page)
  • NAND Backup with RGH3 XeLL written to the console

RGH3 Wiring & Diagrams

PLL Repair on a Phat motherboard (required if bottom pad is damaged)

Phat (Falcon/Jasper)

Alternative Phat Diagram

On Falcon and Jasper motherboards, you can place the a diode on the wire that connects POST and SMC_POST. While it could be skipped, is not recommended to use RGH 3 on a Falcon or Jasper without this diode, as the boot times will be more unstable or inconstant without it. When using a through hole diode, it is recommended to solder it in the middle of the wire instead of soldering it directly to a pad. The wires will be less stiff than the diode's legs, causing less strain to the joint if it moves around. This also applies to the 22K resistor on the wire connecting PLL and SMC_PLL.

It is not recommended to use RGH 3 on Falcon or Jasper without the suggested resistor.

CPU Solder Points

CPU PLL

  • Bottom
    • Bottom
  • Top
    • Top (Requires scraping)

CPU POST

  • Bottom
    • Bottom
  • Top
    • Top (Requires scraping)

SMC Solder Points

  • PhatRGH3SMC.png
    • Alternative SMC_PLL (Top)
      • Topsidepoint.png

Slim (Trinity)

On Trinity, it is recommended to use a 3K to 10K Ohm resistor on the PLL wire. The resistor on Trinity is optional, but recommended for reliability if available. The diode on the POST wire is not used on Trinity or Corona. When using a through hole resistor, it is recommended to solder it in the middle of the wire instead of soldering it directly to a pad. The wires will be less stiff than the diode's legs, causing less strain to the joint if it moves around.

CPU Solder Points

  • CPU PLL (Bottom, no alt point!)
    • RGH1.2 Slim PLL.jpg
  • CPU POST (Bottom, RST can be ignored with RGH3)
    • TrinityPOSTandRST.png

SMC Solder Points

  • SMC_PLL
    • FT2V1
  • SMC_POST
    • R3R22

Slim or E (Corona/Waitsburg/Stingray)

File:5lY3TID.png
Corona POSTFix Installation/Identification

The 1K Ohm resistor on Corona motherboards is optional, but still recommended for reliability if available. It also connects to the wire connecting SMC_PLL and the CPU's PLL. When using a through hole resistor, it is recommended to solder it in the middle of the wire instead of soldering it directly to a pad. The wires will be less stiff than the diode's legs, causing less strain to the joint if it moves around. Make sure to check if the POST point on the bottom is enabled or not using the provided diagram.

CPU Solder Points

  • CPU PLL (Bottom, no alt point!)
    • RGH1.2 Slim PLL.jpg
  • CPU POST (Bottom, RST can be ignored with RGH3)
    • Corona POSTandRST.png

SMC Solder Points

  • Bottom
    • SMC_POST and SMC_PLL

Decrypting the NAND

  1. Connect an Ethernet cable and HDMI cable to the console and power it on. The glitch chip should blink once or more times, and then the console should start into XeLL RELOADED.
  2. Once XeLL finishes, it will display your CPU key and some other info. There is also an IP address.
  3. Enter the IP address into the box on the lower right of J-Runner and click "Get CPU Key". J-Runner will pull the info from the box, and decrypt the NANDs automatically.
    • If you don't want to or aren't able to connect the Xbox 360 to a network or directly to the PC, you can also manually type in the CPU key from XeLL into J-Runner.

Writing New NAND Image

  1. Power down the console, and connect your programmer to the motherboard.
    • If you are using an xFlasher, ensure the switch is set to SPI.
  2. In the upper right of J-Runner, ensure the Glitch2 radio button is selected. Since RGH3 XeLL was written to the NAND earlier, Glitch2 and RGH3 should already be enabled.
  3. Click "Create XeBuild Image". This will take a few moments.
  4. Click "Write NAND".
  5. Disconnect your programmer when the process completes.
  6. Boot the console several times and ensure it boots consistently. If not, make sure your wiring is clean and neat and avoids noisy areas. Run the wires near the X-Clamps for best results.
  7. Return to the RGH main page and continue in the Cleaning Up section.

References