CRT:ADDS 4000: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
(Created page with "{{Infobox/CRT |model = ADDS 4000 |image = ADDS_4000.png |manufacturer = ADDS |type = Terminal |size = 14" |dimensions = Width: 318mm Depth: 330mm Height: 340mm |weight = 29 lbs |tvl = |dot_pitch = |firmware = |earliest = |latest = |regions = |240p/480i = No |480p = No |720p = No |1080i = No |vsync = 60hz/71hz/82hz/100hz |widescreen = No |composite = |s-video = |component = |sdi = |hd-sdi = |chassis = |remote = |controller = |standard_boards = |optional_boards =...")
 
m (Text replacement - "\|service_bulletins \= \n" to "")
 
(11 intermediate revisions by the same user not shown)
Line 2: Line 2:
|model = ADDS 4000
|model = ADDS 4000
|image = ADDS_4000.png
|image = ADDS_4000.png
|manufacturer = ADDS
|manufacturer = Boundless Technologies
|type = Terminal
|type = Text Terminal
|size = 14"
|size = 14"
|dimensions =
|dimensions =
Line 13: Line 13:
|dot_pitch =  
|dot_pitch =  
|firmware =  
|firmware =  
|earliest =  
|earliest = 1997
|latest =  
|latest =  
|regions =
|regions =
Line 32: Line 32:
|standard_boards =
|standard_boards =
|optional_boards =
|optional_boards =
|operation_manual = [[:Media:Sony FV310 Operation Manual.pdf|FV310 Manual]]
|operation_manual =
|service_manual = [[:Media:Sony_BA-5D_Chassis_Service_Manual.pdf|BA-5D Chassis Manual]]
[[:Media:ADDS 4000 Users Guide.pdf|ADDS 4000]]
|service_bulletins =  
[[:Media:ADDS-4000-110-Users Guide.pdf|ADDS 4000/110]]
|brochure = [[:Media:Sony FV310 Brochure.pdf|FV310 Brochure]]
[[:Media:ADDS 4000-160 Users Guide.pdf|ADDS 4000/160]]
[[:Media:ADDS 4000-260 Users Guide.pdf|ADDS 4000/260]]
[[:Media:ADDS 4000 260 LF LFC Users Guide.pdf|ADDS 4000/260 LF/LFC]]
[[:Media:ADDS Ethernet Interface Adapter Users Guide.pdf|Ethernet Adapter]]
|service_manual =  
|brochure =  
[[:Media:ADDS 4000 Spec Sheet.pdf|ADDS 4000]]
[[:Media:ADDS 4000-110 Spec Sheet.pdf|ADDS 4000/110]]
[[:Media:ADDS 4000-150 Spec Sheet.pdf|ADDS 4000/150]]
[[:Media:ADDS 4000-160 4000-260 Spec Sheet.pdf|ADDS 4000-160]]
[[:Media:ADDS 4000-260 Spec Sheet.pdf|ADDS 4000-260]]
[[:Media:ADDS 4000-160 4000-260 Spec Sheet.pdf|ADDS 4000-260 (alt)]]
[[:Media:ADDS 4000-260 LFC Spec Sheet.pdf|ADDS 4000 LFC]]
}}
}}
Text only terminal with a monochrome screen that comes in page-white, amber, or green colors. Compatible with PC101/102/106/107 or ANSI VT-220 keyboards via RJ11 connector on the left side.
The ADDS 4000 series is a series of text-only terminals with a monochrome screen that came in page-white, amber, or green colors. Named after the manufacturer "Applied Digital Data Systems" (later renamed to Boundless Technologies), they are compatible with PC101/102/106/107 or ANSI VT-220 keyboards via RJ11 connector on the left side.


== Terminal Emulators ==  
== Supported Terminal Emulators ==  


The ADDS 4000 series is capable of emulating various terminals depending on model listed below<ref>http://www.boundlessterminals.com/terminals.html</ref>.
The ADDS 4000 series is capable of emulating various terminals depending on model listed below<ref>http://www.boundlessterminals.com/terminals.html</ref>.
Line 70: Line 82:
| VT510, VT520, VT525, Dorio 10 || ADDS Viewpoint; DEC VT-100, VT220, VT320, Dorio 10; Wyse WY-50/50+ , WY-55, WY-60/160, WY-120/150; TeleVideo TVI 910+ , TVI 925/950; SCO Console
| VT510, VT520, VT525, Dorio 10 || ADDS Viewpoint; DEC VT-100, VT220, VT320, Dorio 10; Wyse WY-50/50+ , WY-55, WY-60/160, WY-120/150; TeleVideo TVI 910+ , TVI 925/950; SCO Console
|}
|}
== Connecting to Linux Machine ==
The easiest way to connect the terminal to a Linux machine — such as a Raspberry Pi — is to obtain a [https://www.amazon.com/dp/B00066HL50 DB-25 male to DB-9 female null modem cable] and a [https://www.amazon.com/gp/product/B07XKTQPS3/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 DB-9 male to USB adapter cable]. You must get one labelled "null modem", as it is cross wired to be used without a modem.
Connect the cables to each other, one end to the terminal's EIA port (fastest), and the other to a USB port on your Linux host device.
=== Terminal Setup ===
# Press `Ctrl + Scroll Lock` (may be "PrLne" or "PrMsg" on your keyboard) to access Setup menu.
# Press F1 to enter Quick menu (if not already selected). Set the following:
#: `Host/Printer=EIA/None (enables EIA port to be connected to Linux host)`
# Press F2 to enter General menu. Set the following:
#: `Emulation=VT100`
#: `(and optional settings to turn down the bell noise and set a screen saver to protect the CRT)`
# Press F3 to enter Display menu. Set the following:
#: `Display Cursor=On`
#: `Page Length=24`
#: `Screen Length=26`
#: `Columns=80`
# Press F4 to enter Keyboard menu. Set the following:
#: `Key Mode=ASCII`
# Press F6 to enter Ports menu. Set the following:
#: `EIA Baud Rate=115200 (if not available, note the value you choose)`
#: `EIA Xmt=Xon-Xoff`
#: `EIA Data Format=8/1/N`
#: `EIA Recv=Xany-Xoff(XPC)`
#: `EIA Parity Check=Off`
#: `EIA Xmt Pace=Baud`
# Press F7 to enter Host menu. Set the following:
#: `Comm Mode=Full Duplex`
# Press F9 to enter Emulation menu. Set the following:
#: `ANSI-ID=VT100 (this will identify the terminal as a VT100 terminal to Linux)`
#: `Status Line=Off (recommended to prevent burn-in with line/text at top of screen)`
# Press F13 (may be "Print" or "Print Screen" on your keyboard) to enter Exec menu.
#* Press Enter on "Save Terminal" and wait for "DONE" message.
#* Press Enter on "Save Session" and wait for "DONE" message.
# Press F14 (may be "Hold", "Break", or "Pause" on your keyboard) and Y to save and exit.
=== Linux Setup ===
# Enable the terminal console to be accessible by serial.
#* On a Raspberry Pi, this can be set by running `sudo raspi-config` and enabling the "Serial Port" option under Interface Options; or by running `sudo vi /boot/config.txt` and adding an `[all]` section at the bottom followed by `enable_uart=1`.
# Enable the USB serial port and set the baud rate to match the one you had set in the previous section.
#* On a Raspberry Pi, you can do this by entering the commands:
#*: `sudo stty -F /dev/ttyUSB0 115200`
#*: `sudo systemctl enable [email protected]`
#*: `sudo systemctl start [email protected]`
# If a login prompt isn't shown on the physical terminal, reboot the physical terminal followed by the Linux machine and it should prompt you for a login on the physical terminal.
== References ==

Latest revision as of 04:21, 1 November 2023

ADDS 4000
ADDS 4000.png
Information
Manufacturer Boundless Technologies
Type Text Terminal
Size 14"
240p/480i No
480p No
720p No
1080i No
Vsync 60hz/71hz/82hz/100hz
Widescreen No
Dimensions Width: 318mm

Depth: 330mm

Height: 340mm
Weight 29 lbs
Earliest Date 1997
Links
Operation Manual ADDS 4000

ADDS 4000/110 ADDS 4000/160 ADDS 4000/260 ADDS 4000/260 LF/LFC

Ethernet Adapter
Brochure ADDS 4000

ADDS 4000/110 ADDS 4000/150 ADDS 4000-160 ADDS 4000-260 ADDS 4000-260 (alt)

ADDS 4000 LFC

The ADDS 4000 series is a series of text-only terminals with a monochrome screen that came in page-white, amber, or green colors. Named after the manufacturer "Applied Digital Data Systems" (later renamed to Boundless Technologies), they are compatible with PC101/102/106/107 or ANSI VT-220 keyboards via RJ11 connector on the left side.

Supported Terminal Emulators

The ADDS 4000 series is capable of emulating various terminals depending on model listed below[1].

Model Emulators Available
ADDS 4000/110 ADDS Viewpoint A1, A2, 3A, 3A+; Lear Siegler ADM 3A
ADDS 4000/150 ADDS Viewpoint and Regent 40; Wyse WY-50, WY-75, TeleVideo TVI-910, TVI-920,TVI-925; Hazeltine HZ-1500; DEC VT52, VT100; PCTerm
ADDS 60 ADDS Viewpoint, AT 386 (Unix console), DEC VT100, VT220, VT320, Wyse WY-50/50+ WY-60, TeleVideo TVI 925, PC Term, SCO Console, BBS ANSI, Wordperfect Graphics
ADDS 4000 ADDS Viewpoint and Regent 40; Wyse WY-50, WY-75, TeleVideo TVI-910, TVI-920,TVI-925; Hazeltine HZ-1500; DEC VT52, VT100; PCTerm, SCO Console
ADDS 4000/160 ADDS Viewpoint, ADDS Viewpoint 60, DEC VT100, VT220, VT320, VT420 PC TERM, Wyse WY-50/50+, WY-60 TeleVideo TVI 925, PC Term (925 PC)
ADDS 4000/260 ADDS Viewpoint, DEC VT100, VT220, VT320, Wyse WY-50/50+, WY-60 TeleVideo TVI 925, PC Term (925 PC), SCO console, AT 386 (UNIX console), WordPerfect graphics
ADDS 4000/260LF ADDS Viewpoint, AT 386 (Unix console) DEC VT100, VT220, VT320, Wyse WY-50/50+, WY-60, TeleVideo TVI 925, PC Term, SCO Console, WordPerfect graphics
ADDS 4000/260LFC Same as 4000/260LF plus WY-325, WY-350
ADDS C1099A HP 700/96 (factory default); Wyse WY-60, WY-50/50+, DEC VT320, VT220, VT100; ADDS Viewpoint, PCTerm (925 PC); TeleVideo TVI-925; SCO console, AT 386 (UNIX console)
ADDS 3153 IBM 3151, Wyse WY-60, WY-50/50+, DEC VT320, VT220, VT100; ADDS Viewpoint, PCTerm (925 PC); TeleVideo TVI-925; SCO console, AT 386 (UNIX console)
ADDS 3153 LF Same as ADDS 3153
VT510, VT520, VT525, Dorio 10 ADDS Viewpoint; DEC VT-100, VT220, VT320, Dorio 10; Wyse WY-50/50+ , WY-55, WY-60/160, WY-120/150; TeleVideo TVI 910+ , TVI 925/950; SCO Console

Connecting to Linux Machine

The easiest way to connect the terminal to a Linux machine — such as a Raspberry Pi — is to obtain a DB-25 male to DB-9 female null modem cable and a DB-9 male to USB adapter cable. You must get one labelled "null modem", as it is cross wired to be used without a modem.

Connect the cables to each other, one end to the terminal's EIA port (fastest), and the other to a USB port on your Linux host device.

Terminal Setup

  1. Press Ctrl + Scroll Lock (may be "PrLne" or "PrMsg" on your keyboard) to access Setup menu.
  2. Press F1 to enter Quick menu (if not already selected). Set the following:
    Host/Printer=EIA/None (enables EIA port to be connected to Linux host)
  3. Press F2 to enter General menu. Set the following:
    Emulation=VT100
    (and optional settings to turn down the bell noise and set a screen saver to protect the CRT)
  4. Press F3 to enter Display menu. Set the following:
    Display Cursor=On
    Page Length=24
    Screen Length=26
    Columns=80
  5. Press F4 to enter Keyboard menu. Set the following:
    Key Mode=ASCII
  6. Press F6 to enter Ports menu. Set the following:
    EIA Baud Rate=115200 (if not available, note the value you choose)
    EIA Xmt=Xon-Xoff
    EIA Data Format=8/1/N
    EIA Recv=Xany-Xoff(XPC)
    EIA Parity Check=Off
    EIA Xmt Pace=Baud
  7. Press F7 to enter Host menu. Set the following:
    Comm Mode=Full Duplex
  8. Press F9 to enter Emulation menu. Set the following:
    ANSI-ID=VT100 (this will identify the terminal as a VT100 terminal to Linux)
    Status Line=Off (recommended to prevent burn-in with line/text at top of screen)
  9. Press F13 (may be "Print" or "Print Screen" on your keyboard) to enter Exec menu.
    • Press Enter on "Save Terminal" and wait for "DONE" message.
    • Press Enter on "Save Session" and wait for "DONE" message.
  10. Press F14 (may be "Hold", "Break", or "Pause" on your keyboard) and Y to save and exit.

Linux Setup

  1. Enable the terminal console to be accessible by serial.
    • On a Raspberry Pi, this can be set by running sudo raspi-config and enabling the "Serial Port" option under Interface Options; or by running sudo vi /boot/config.txt and adding an [all] section at the bottom followed by enable_uart=1.
  2. Enable the USB serial port and set the baud rate to match the one you had set in the previous section.
  3. If a login prompt isn't shown on the physical terminal, reboot the physical terminal followed by the Linux machine and it should prompt you for a login on the physical terminal.

References

  1. ↑ http://www.boundlessterminals.com/terminals.html
Retrieved from "https://consolemods.org/wiki/index.php?title=CRT:ADDS_4000&oldid=29681"