Xbox 360:RGH & JTAG Identification: Difference between revisions
mNo edit summary |
m (Text replacement - "Category:Xbox360" to "Category:Xbox 360") |
||
(15 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
[[Category:Xbox 360]] | |||
This is a basic guide on how to properly identify what method was used to modify your Xbox 360. Proper identification is necessary when updating/building a new image with XeBuild for your console. | This is a basic guide on how to properly identify what method was used to modify your Xbox 360. Proper identification is necessary when updating/building a new image with XeBuild for your console. | ||
Line 5: | Line 6: | ||
{{Warning|Relying solely on Dashlaunch to verify your RGH/JTAG type is not recommended. Disassembly of the console and examining the installation is the only certain way to completely verify your installation type.}} | {{Warning|Relying solely on Dashlaunch to verify your RGH/JTAG type is not recommended. Disassembly of the console and examining the installation is the only certain way to completely verify your installation type.}} | ||
== Winbond 2K RAM == | |||
Before covering RGH and JTAG types, a quick warning for Stringray motherboards. If you have a Stingray and you have Winbond 2K RAM on your motherboard (RAM will display model number W641GG2KB-14) you '''MUST''' check the box for it in JRunner no matter what RGH method your console is using. | |||
[[File:Winbond-W641GG2KB-14.jpg|left|thumb|Exampel of Winbond 2K RAM. Credit: XenonLibrary]] | |||
Line 21: | Line 21: | ||
[[File:Winbond2k JRunner.jpg|left|thumb|Checkbox in JRunner that is required if you have Winbond 2K RAM.]] | |||
Line 33: | Line 31: | ||
{{br}} | |||
==RGH3== | |||
===Dashlaunch=== | |||
A RGH3 installation will display '''Trinity''' next to Flash, no matter your motherboard revision, and will display '''Glitch''' next to Type. | |||
[[File: | [[File:CoronaRGH3FlashExample.jpg|left|thumb|Example of Corona motherboard with RGH3. Credit: MrMario2011]] | ||
Line 43: | Line 45: | ||
{{br}} | |||
===Install === | |||
A RGH3 install can be identified by the lack of a glitch chip, as RGH3 does not require one. A typical RGH3 install will have 2 wires on the bottom of the motherboard. In most cases you can verify an RGH3 install without disassembly of the console. Glitch chips have a debug LED that will flash while the console is booting; if your console matches the description listed above in Dashlaunch, look into the top vent of your console immediately after powering it on. If you see a quickly flashing LED (typically green, red, or blue) that stops flashing once the console is booted then you have a glitch chip and do not have RGH3. If no flashing LED is present then it is a good assumption you have an RGH3 install. | |||
[[File:RGH3 Corona w-o POSTfix .jpg|left|thumb|Example of Corona (Slim Motherboard) with RGH3.|300x300px]] | |||
Line 50: | Line 56: | ||
[[File:RGH3 Phat Example.jpg|left|thumb|Example of Jasper (Phat Motherboard) with RGH3.]] | |||
Line 62: | Line 67: | ||
Line 73: | Line 74: | ||
{{br}} | |||
===JRunner Settings=== | |||
To build/update a NAND image with RGH3, use these settings in JRunner:[[File:RGH3 Jrunner Settings.jpg|left|thumb]] | |||
{{br}} | |||
== RGH1.2 / RGH1== | |||
[[File: | ===Dashlaunch === | ||
A console with RGH1.2 will have matching names under Board and Flash (Ex: Board: Falcon, Flash: Falcon) and will be listed as '''Glitch2''', however a RGH1 console will be listed as '''Glitch''' while still having a matching Board and Flash. | |||
[[File:TrinityRGH2Example.jpg|left|thumb|Example of RGH 1.2 Trinity console in Dashlaunch. Credit: MrMario2011]] | |||
Line 99: | Line 101: | ||
{{br}} | |||
===Install=== | |||
RGH1.2 and RGH1 utilize a glitch chip, use PLL slow-down, and will have a nearly identical install on Phats, but will use different connections for POST. The install may have varying points for RST and STBY_CLK, but the two constants will be PLL and POST. RGH1 is not possible on Slim consoles, so if your Slim has a glitch chip and uses PLL you have a RGH1.2 install. | |||
Summary: | |||
Phat + Glitch2 + PLL = RGH1.2 | |||
Phat + Glitch + PLL = RGH1 | |||
Slim + Glitch2 + PLL = RGH1.2 | |||
[[File:RGH1.2 BottomView.jpg|thumb|Example of RGH1.2 on a phat, bottom view of motherboard. Credit: Cheez|none]] | |||
[[File:RGH1.2 TopView.jpg|thumb|Example of RGH1.2 on a phat, top view of motherboard. Credit: Cheez|none]] | |||
[[File:RGH1 vs RGH1.2 POST.jpg|thumb|RGH1 and RGH1.2 POST locations. Credit: Cheez|none]] | |||
[[File:RGH1.2 Slim PLL.jpg|thumb|A slim console with a glitch chip using this connection (PLL) will be RGH1.2 Credit: Octal450|none]] | |||
{{br}} | |||
===JRunner Settings | ===JRunner Settings=== | ||
To build/update a NAND image with RGH1, use these settings in JRunner: | To build/update a NAND image with RGH1, use these settings in JRunner: | ||
[[File:RGH1 Jrunner Settings.jpg|left|thumb]] | [[File:RGH1 Jrunner Settings.jpg|left|thumb]] | ||
Line 152: | Line 142: | ||
{{br}} | |||
To build/update a NAND image with RGH1.2, use these settings in JRunner:[[File:RGH1.2 JRunner Settings.jpg|left|thumb]] | To build/update a NAND image with RGH1.2, use these settings in JRunner:[[File:RGH1.2 JRunner Settings.jpg|left|thumb]] | ||
Line 162: | Line 153: | ||
{{br}} | |||
==S-RGH / RGH2== | ==S-RGH / RGH2== | ||
===Dashlaunch | ===Dashlaunch=== | ||
S-RGH and RGH2 will appear the same as RGH1.2 in Dashlaunch, with a matching Board/Flash and '''Glitch2'''. Please reference the example image in the RGH1.2 guide. | S-RGH and RGH2 will appear the same as RGH1.2 in Dashlaunch, with a matching Board/Flash and '''Glitch2'''. Please reference the example image in the RGH1.2 guide. | ||
===Install | ===Install=== | ||
While S-RGH and RGH2 will match the details of RGH1.2 in Dashlaunch, the installs are vastly different. RGH2 and S-RGH use i2C slowdown and can be quickly identified by the glitch chip connections going to SDA and SCL on the J2B1 header on Phats, and the J2C3 header on Slims. S-RGH and RGH2 are technically the same install, but S-RGH utilizes SMC Speed-Up (SMC+). | While S-RGH and RGH2 will match the details of RGH1.2 in Dashlaunch, the installs are vastly different. RGH2 and S-RGH use i2C slowdown and can be quickly identified by the glitch chip connections going to SDA and SCL on the J2B1 header on Phats, and the J2C3 header on Slims. S-RGH and RGH2 are technically the same install, but S-RGH utilizes SMC Speed-Up (SMC+). | ||
[[File:SRGH Install.jpg|left|thumb|S-RGH install on a Trinity. Credit:TheModShop]] | [[File:SRGH Install.jpg|left|thumb|S-RGH install on a Trinity. Credit:TheModShop]] | ||
Line 193: | Line 182: | ||
{{br}} | |||
===JRunner Settings=== | |||
===JRunner Settings | |||
To build/update a NAND image with RGH2 or S-RGH, use these settings in JRunner: | To build/update a NAND image with RGH2 or S-RGH, use these settings in JRunner: | ||
[[File:RGH1.2 JRunner Settings.jpg|left|thumb]] | [[File:RGH1.2 JRunner Settings.jpg|left|thumb]] | ||
Line 206: | Line 194: | ||
{{br}} | |||
==EXT_CLK== | ==EXT_CLK== | ||
===Dashlaunch | ===Dashlaunch=== | ||
EXT_CLK can only be preformed in Xenon and Zephyr motherboards. The information for EXT_CLK will appear the same as RGH1.2/S-RGH/RGH2 in Dashlaunch with Board/Flash matching and Flash as '''Glitch2'''. | EXT_CLK can only be preformed in Xenon and Zephyr motherboards. The information for EXT_CLK will appear the same as RGH1.2/S-RGH/RGH2 in Dashlaunch with Board/Flash matching and Flash as '''Glitch2'''. | ||
===Install | ===Install=== | ||
An EXT_CLK install will appear nearly identical to a RGH1.2 install, but instead of using PLL it will use EXT_CLK. If your console has a glitch chip, is a Xenon or Zephyr, and is using the EXT_CLK point then you have a EXT_CLK install. | An EXT_CLK install will appear nearly identical to a RGH1.2 install, but instead of using PLL it will use EXT_CLK. If your console has a glitch chip, is a Xenon or Zephyr, and is using the EXT_CLK point then you have a EXT_CLK install. | ||
[[File:EXTCLK BottomView.jpg|left|thumb|Bottom view of Zephyr motherboard with EXT_CLK. Credit: Cheez]] | [[File:EXTCLK BottomView.jpg|left|thumb|Bottom view of Zephyr motherboard with EXT_CLK. Credit: Cheez]] | ||
Line 230: | Line 216: | ||
[[File:EXTCLK TopView.jpg|left|thumb|Top view of Zephyr motherboard with EXT_CLK. Credit: Cheez]] | [[File:EXTCLK TopView.jpg|left|thumb|Top view of Zephyr motherboard with EXT_CLK. Credit: Cheez]] | ||
Line 257: | Line 242: | ||
{{br}} | |||
===JRunner Settings=== | |||
To build/update a NAND image with RGH2 or S-RGH, use these settings in JRunner: | |||
'''WARNING:''' Leave SMC+ unchecked if you have a Xenon motherboard. | |||
[[File:RGH1.2 JRunner Settings.jpg|left|thumb]] | [[File:RGH1.2 JRunner Settings.jpg|left|thumb]] | ||
Line 271: | Line 257: | ||
{{br}} | |||
== JTAG / R-JTAG / R-JTOP== | |||
===Dashlaunch === | |||
===Dashlaunch | |||
A console with a JTAG install will be the most uncommon install we cover in this guide. A JTAG install requires a phat console on dashboard 7371 or lower and an unpatched CB, and does not use a glitch chip. A R-JTAG or R-JTOP install uses a glitch chip and RGH to re-enable the JTAG exploit on phat consoles with a dashboard higher than 7371. You can identify if you have a JTAG/R-JTAG/R-JTOP console if Dashlaunch has '''JTAG''' listed as the Type. | A console with a JTAG install will be the most uncommon install we cover in this guide. A JTAG install requires a phat console on dashboard 7371 or lower and an unpatched CB, and does not use a glitch chip. A R-JTAG or R-JTOP install uses a glitch chip and RGH to re-enable the JTAG exploit on phat consoles with a dashboard higher than 7371. You can identify if you have a JTAG/R-JTAG/R-JTOP console if Dashlaunch has '''JTAG''' listed as the Type. | ||
Line 287: | Line 273: | ||
{{br}} | |||
===Install=== | |||
===Install | |||
There are 2 different types of JTAG installs, ARGON_DATA and AUD_CLAMP. If you have a Xenon motherboard, it will be ARGON_DATA. Falcon, Zephyr, and Jasper motherboards can use both ARGON_DATA and AUD_CLAMP. On these motherboards your install type can be identified by where your J2D2.2 connection is going. AUD_CLAMP also has 3 different variations; AUD_CLAMP, Boxxdr, and Open Tray. | There are 2 different types of JTAG installs, ARGON_DATA and AUD_CLAMP. If you have a Xenon motherboard, it will be ARGON_DATA. Falcon, Zephyr, and Jasper motherboards can use both ARGON_DATA and AUD_CLAMP. On these motherboards your install type can be identified by where your J2D2.2 connection is going. AUD_CLAMP also has 3 different variations; AUD_CLAMP, Boxxdr, and Open Tray. | ||
Line 295: | Line 280: | ||
A R-JTAG or R-JTOP install will have a JTAG install on the motherboard, and will show as JTAG in Dashlaunch, but will also have a glitch chip in place. | A R-JTAG or R-JTOP install will have a JTAG install on the motherboard, and will show as JTAG in Dashlaunch, but will also have a glitch chip in place. | ||
[[File:AUDCLAMP vs ARGON.jpg|left|thumb|Bottom side of motherboard showing an example of JTAG AUD_CLAMP. If your connection from J2D2.2 is going to the yellow arrow, you have AUD_CLAMP. If the connection is going to either of the red arrows, you have ARGON_DATA. Credit: Cheez]] | [[File:AUDCLAMP vs ARGON.jpg|left|thumb|Bottom side of motherboard showing an example of JTAG AUD_CLAMP. If your connection from J2D2.2 is going to the yellow arrow, you have AUD_CLAMP. If the connection is going to either of the red arrows, you have ARGON_DATA. Credit: Cheez]] | ||
Line 309: | Line 293: | ||
[[File:Non-Xenon-JTAG5.png|left|thumb|Example of Boxxdr + AUD_CLAMP. Credit: Boxxdr]] | [[File:Non-Xenon-JTAG5.png|left|thumb|Example of Boxxdr + AUD_CLAMP. Credit: Boxxdr]] | ||
Line 367: | Line 350: | ||
===JRunner Settings | |||
{{br}} | |||
===JRunner Settings=== | |||
To build/update a NAND image with JTAG ARGON_DATA, use these settings in JRunner: | To build/update a NAND image with JTAG ARGON_DATA, use these settings in JRunner: | ||
[[File:Jtagjrunnersettings.jpg|left|thumb]] | [[File:Jtagjrunnersettings.jpg|left|thumb]] | ||
Line 382: | Line 371: | ||
{{br}} | |||
To build/update a NAND image with JTAG AUD_CLAMP, use these settings in JRunner: | To build/update a NAND image with JTAG AUD_CLAMP, use these settings in JRunner: | ||
[[File:Audclamp Jrunner Settings.jpg|left|thumb]] | [[File:Audclamp Jrunner Settings.jpg|left|thumb]] | ||
Line 397: | Line 386: | ||
{{br}} | |||
To build/update a NAND image with R-JTAG or R-JTOP, use these settings in JRunner: | |||
'''WARNING:''' Confirm if you have an AUD_CLAMP or ARGON_DATA install with your R-JTAG/JTOP install. If your install is AUD_CLAMP, ensure you check the box for it along with the box for R-JTAG. | |||
[[File:Rjtag Jrunner Settings.jpg|left|thumb]] | [[File:Rjtag Jrunner Settings.jpg|left|thumb]] |
Latest revision as of 20:20, 4 September 2024
This is a basic guide on how to properly identify what method was used to modify your Xbox 360. Proper identification is necessary when updating/building a new image with XeBuild for your console.
When loading Dashlaunch, in the bottom right corner you will see basic information about your console such as motherboard, flash, glitch type, and kernel. The flash and glitch type can be helpful in identifying what installation method your console has.
Relying solely on Dashlaunch to verify your RGH/JTAG type is not recommended. Disassembly of the console and examining the installation is the only certain way to completely verify your installation type. |
Winbond 2K RAM
Before covering RGH and JTAG types, a quick warning for Stringray motherboards. If you have a Stingray and you have Winbond 2K RAM on your motherboard (RAM will display model number W641GG2KB-14) you MUST check the box for it in JRunner no matter what RGH method your console is using.
RGH3
Dashlaunch
A RGH3 installation will display Trinity next to Flash, no matter your motherboard revision, and will display Glitch next to Type.
Install
A RGH3 install can be identified by the lack of a glitch chip, as RGH3 does not require one. A typical RGH3 install will have 2 wires on the bottom of the motherboard. In most cases you can verify an RGH3 install without disassembly of the console. Glitch chips have a debug LED that will flash while the console is booting; if your console matches the description listed above in Dashlaunch, look into the top vent of your console immediately after powering it on. If you see a quickly flashing LED (typically green, red, or blue) that stops flashing once the console is booted then you have a glitch chip and do not have RGH3. If no flashing LED is present then it is a good assumption you have an RGH3 install.
JRunner Settings
To build/update a NAND image with RGH3, use these settings in JRunner:
RGH1.2 / RGH1
Dashlaunch
A console with RGH1.2 will have matching names under Board and Flash (Ex: Board: Falcon, Flash: Falcon) and will be listed as Glitch2, however a RGH1 console will be listed as Glitch while still having a matching Board and Flash.
Install
RGH1.2 and RGH1 utilize a glitch chip, use PLL slow-down, and will have a nearly identical install on Phats, but will use different connections for POST. The install may have varying points for RST and STBY_CLK, but the two constants will be PLL and POST. RGH1 is not possible on Slim consoles, so if your Slim has a glitch chip and uses PLL you have a RGH1.2 install.
Summary:
Phat + Glitch2 + PLL = RGH1.2
Phat + Glitch + PLL = RGH1
Slim + Glitch2 + PLL = RGH1.2
JRunner Settings
To build/update a NAND image with RGH1, use these settings in JRunner:
To build/update a NAND image with RGH1.2, use these settings in JRunner:
S-RGH / RGH2
Dashlaunch
S-RGH and RGH2 will appear the same as RGH1.2 in Dashlaunch, with a matching Board/Flash and Glitch2. Please reference the example image in the RGH1.2 guide.
Install
While S-RGH and RGH2 will match the details of RGH1.2 in Dashlaunch, the installs are vastly different. RGH2 and S-RGH use i2C slowdown and can be quickly identified by the glitch chip connections going to SDA and SCL on the J2B1 header on Phats, and the J2C3 header on Slims. S-RGH and RGH2 are technically the same install, but S-RGH utilizes SMC Speed-Up (SMC+).
JRunner Settings
To build/update a NAND image with RGH2 or S-RGH, use these settings in JRunner:
EXT_CLK
Dashlaunch
EXT_CLK can only be preformed in Xenon and Zephyr motherboards. The information for EXT_CLK will appear the same as RGH1.2/S-RGH/RGH2 in Dashlaunch with Board/Flash matching and Flash as Glitch2.
Install
An EXT_CLK install will appear nearly identical to a RGH1.2 install, but instead of using PLL it will use EXT_CLK. If your console has a glitch chip, is a Xenon or Zephyr, and is using the EXT_CLK point then you have a EXT_CLK install.
JRunner Settings
To build/update a NAND image with RGH2 or S-RGH, use these settings in JRunner:
WARNING: Leave SMC+ unchecked if you have a Xenon motherboard.
JTAG / R-JTAG / R-JTOP
Dashlaunch
A console with a JTAG install will be the most uncommon install we cover in this guide. A JTAG install requires a phat console on dashboard 7371 or lower and an unpatched CB, and does not use a glitch chip. A R-JTAG or R-JTOP install uses a glitch chip and RGH to re-enable the JTAG exploit on phat consoles with a dashboard higher than 7371. You can identify if you have a JTAG/R-JTAG/R-JTOP console if Dashlaunch has JTAG listed as the Type.
Install
There are 2 different types of JTAG installs, ARGON_DATA and AUD_CLAMP. If you have a Xenon motherboard, it will be ARGON_DATA. Falcon, Zephyr, and Jasper motherboards can use both ARGON_DATA and AUD_CLAMP. On these motherboards your install type can be identified by where your J2D2.2 connection is going. AUD_CLAMP also has 3 different variations; AUD_CLAMP, Boxxdr, and Open Tray.
A R-JTAG or R-JTOP install will have a JTAG install on the motherboard, and will show as JTAG in Dashlaunch, but will also have a glitch chip in place.
JRunner Settings
To build/update a NAND image with JTAG ARGON_DATA, use these settings in JRunner:
To build/update a NAND image with JTAG AUD_CLAMP, use these settings in JRunner:
To build/update a NAND image with R-JTAG or R-JTOP, use these settings in JRunner:
WARNING: Confirm if you have an AUD_CLAMP or ARGON_DATA install with your R-JTAG/JTOP install. If your install is AUD_CLAMP, ensure you check the box for it along with the box for R-JTAG.