Genesis:Triple Bypass Mod Model 3 VA1: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
m (fixed typo)
 
(11 intermediate revisions by 3 users not shown)
Line 1: Line 1:
== Sega Genesis Model 3 - VA1 Triple Bypass Install Tutorial ==
This document will serve as clear step-by-step instructions for installing the 3BP on the Genesis Model 3, revision VA1.
This guide is in progress and will be updated as frequently as possible until complete.  


=== Introduction ===
== Warnings ==
The following is a guide for installing the Triple Bypass Version 2 (3PB) modification on your Sega Genesis Model 3, VA1 revision. The eventual goal of this document, like the rest of the 3BP entries in the wiki, is to serve as the definitive step-by-step instruction for this installation.
Please read the below warnings before proceeding!
* This guide expects you to have a basic understanding of how to open up your Genesis Model 3 and to have basic soldering skills.
* This mod permanently alters your device.
* This mod should not be done by a beginner and is considered intermediate/advanced.
* Make sure power is disconnected before proceeding.
* After performing this mod you will no longer be able to use composite. You’ll be required to use RGB (or HD Retrovision) cables from this point forward.
* '''Proceed at your own risk!'''


=== WARNINGS ===
== Tools Required ==
* Flush cutters
* Snips
* Soldering iron
* Solder
* Flux
* Solder wick
* 28 or 30 AWG wire


=== Tools required: ===
== Installation ==
[[File:Genesis_3_VA1_3BP_Top_Modded.jpg|200px|thumb|The top of the motherboard post-modification (green wires are the [[Genesis:Restoring_CD_Audio_(Model_3)|Sega CD audio fix]]).]] [[File:Genesis_3_VA1_3BP_Bottom_Modded.jpg|200px|thumb|The bottom of the motherboard post-modification.]]


==Installation Pictures==
# Start by removing the shell from your console. Remove the 4 screws at the bottom then turn it back upright and lift off the top shell. Remove the screws on the metal shielding and lift the shield off. Next, remove the 2 screws on the sides of the cartridge slot. Now you can lift the motherboard out of the bottom half of the shell.
In the near future, full step-by-step instruction will be provided. Until then presented here are three pictures of the recommended installation method to aid in the process.  
# Cut this trace and verify with a multimeter that there is no continuity between the two points. <br> [[File:Genesis_3_VA1_3BP_Bottom_Trace_Cut.png]]
# Mount the bypass board on the top of the motherboard. The recommended spot is on the right-hand side on the large solder joints sticking up.
# Assuming you mounted the triple bypass board in the recommended spot, the bypass board itself now blocks a hole where a plastic standoff on the shell is supposed to go. Completely remove the plastic standoff by trimming it with flush cutters. <br> [[File:Genesis 3 3BP Standoff.png|500px]]
# Lift the RGB pins (pins 21, 22, and 23) from the CXA1645M chip. <br> [[File:Genesis3VA2_3BPv2_Jose3.jpg|400px]]
# Solder wires from the video signals (RGBS) pads on the bypass board to the vias shown here. [[File:Genesis 3 VA1 3BP RGBS.png]]
# Remove these five components from the motherboard. Also remove the electrolytic capacitor CE10 (mono output capacitor) and CE7 (composite video output) near the miniDIN connector. <br> [[File:Genesis_3_VA1_3BP_Component_Removal.png]]
# Solder wires from the audio signals (YL/YR/PSG) pads on the bypass board to these resistors on the bottom side of the motherboard, snaking the wires through the controller ports to the top side of the motherboard. <br> [[File:Genesis 3 VA1 3BP Controller Ports.png]]
# Solder wires from the audio signal output (XL/XR) pads on the bypass board to the cart connectors pins B1 (XL) and B3 (XR). <br> [[File:Genesis_3_VA1_3BP_XL_XR.png]]


The bottom of the motherboard pre-modification.
== Post-Installation Fixes ==


[[File:Genesis_3_VA1_3BP_Bottom_Pre-Mod.jpg|200px]]
If you are planning on using a Mega SD or Mega EverDrive PRO, you can easily restore Sega CD audio with the instructions found on [[Genesis:Restoring_CD_Audio_(Model_3)|this page]].


The bottom of the motherboard post-modification.
If you followed this guide and lifted the RGB pins, you may want to apply [[Genesis:RGB_Bypass_Color_Fix|this simple fix for the color]].
 
[[File:Genesis_3_VA1_3BP_Bottom_Modded.jpg|200px]]
 
The top of the motherboard post-modification.
 
[[File:Genesis_3_VA1_3BP_Top_Modded.jpg|200px]]

Latest revision as of 19:12, 10 September 2024

This document will serve as clear step-by-step instructions for installing the 3BP on the Genesis Model 3, revision VA1.

Warnings

Please read the below warnings before proceeding!

  • This guide expects you to have a basic understanding of how to open up your Genesis Model 3 and to have basic soldering skills.
  • This mod permanently alters your device.
  • This mod should not be done by a beginner and is considered intermediate/advanced.
  • Make sure power is disconnected before proceeding.
  • After performing this mod you will no longer be able to use composite. You’ll be required to use RGB (or HD Retrovision) cables from this point forward.
  • Proceed at your own risk!

Tools Required

  • Flush cutters
  • Snips
  • Soldering iron
  • Solder
  • Flux
  • Solder wick
  • 28 or 30 AWG wire

Installation

The top of the motherboard post-modification (green wires are the Sega CD audio fix).
The bottom of the motherboard post-modification.
  1. Start by removing the shell from your console. Remove the 4 screws at the bottom then turn it back upright and lift off the top shell. Remove the screws on the metal shielding and lift the shield off. Next, remove the 2 screws on the sides of the cartridge slot. Now you can lift the motherboard out of the bottom half of the shell.
  2. Cut this trace and verify with a multimeter that there is no continuity between the two points.
    Genesis 3 VA1 3BP Bottom Trace Cut.png
  3. Mount the bypass board on the top of the motherboard. The recommended spot is on the right-hand side on the large solder joints sticking up.
  4. Assuming you mounted the triple bypass board in the recommended spot, the bypass board itself now blocks a hole where a plastic standoff on the shell is supposed to go. Completely remove the plastic standoff by trimming it with flush cutters.
    Genesis 3 3BP Standoff.png
  5. Lift the RGB pins (pins 21, 22, and 23) from the CXA1645M chip.
    Genesis3VA2 3BPv2 Jose3.jpg
  6. Solder wires from the video signals (RGBS) pads on the bypass board to the vias shown here. Genesis 3 VA1 3BP RGBS.png
  7. Remove these five components from the motherboard. Also remove the electrolytic capacitor CE10 (mono output capacitor) and CE7 (composite video output) near the miniDIN connector.
    Genesis 3 VA1 3BP Component Removal.png
  8. Solder wires from the audio signals (YL/YR/PSG) pads on the bypass board to these resistors on the bottom side of the motherboard, snaking the wires through the controller ports to the top side of the motherboard.
    Genesis 3 VA1 3BP Controller Ports.png
  9. Solder wires from the audio signal output (XL/XR) pads on the bypass board to the cart connectors pins B1 (XL) and B3 (XR).
    Genesis 3 VA1 3BP XL XR.png

Post-Installation Fixes

If you are planning on using a Mega SD or Mega EverDrive PRO, you can easily restore Sega CD audio with the instructions found on this page.

If you followed this guide and lifted the RGB pins, you may want to apply this simple fix for the color.