Xbox 360:JR Programmer: Difference between revisions
Jump to navigation
Jump to search
mNo edit summary |
m (Text replacement - "Category:Xbox360" to "Category:Xbox 360") |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
The Xecuter JR Programmer is a device used to read/write to Xbox 360 NANDs and program glitch chips. It works in conjunction with the Windows program | [[Category:Xbox 360]] | ||
The Xecuter JR Programmer is a device used to read/write to Xbox 360 NANDs and program glitch chips. It works in conjunction with the Windows program J-Runner and can be used for JTAG and RGH installs. It also can be used with the Xecuter X360USB PRO device to flash DVD drives. | |||
Drivers and updates for the device can be found within the program | Drivers and updates for the device can be found within the program J-Runner. | ||
| Line 15: | Line 16: | ||
# Set the switch to JTAG-XSVF if not set to that already. | # Set the switch to JTAG-XSVF if not set to that already. | ||
# Plug in the JR Programmer to your computer via the mini USB cable and plug in the glitch chip using the glitch chip programming cables. | # Plug in the JR Programmer to your computer via the mini USB cable and plug in the glitch chip using the glitch chip programming cables. | ||
# Launch | # Launch J-Runner, select Advanced > Custom NAND/CR Functions, then choose your XSVF file, and start. | ||
==Updating the JR Programmer Firmware== | ==Updating the JR Programmer Firmware== | ||
| Line 27: | Line 28: | ||
===General Tips=== | ===General Tips=== | ||
* Verify all solder points are well done and not bridged. If unsure or think it is badly done, reflow the solder. | * Verify all solder points are well done and not bridged. If unsure or think it is badly done, reflow the solder. | ||
* Make sure you are running | * Make sure you are running J-Runner as Administrator (Right click J-Runner > Run as Administrator). | ||
* | * J-Runner may have issues with Windows 10, either find an older operating system to flash from or try [https://github.com/Octal450/J-Runner-with-Extras/releases/latest J-Runner with Extras] (you must [[Xbox 360:Unsigned Drivers|disable driver signing]]). If you are planning on using an older operating system, you can use Windows 7 or XP in a VM with USB access (make sure to install .NET Framework or J-Runner won't work). | ||
* Reinstall the drivers by opening Device Manager and right clicking the entry for JR Programmer and choosing Update Drivers > Browse > My Computer > | * Reinstall the drivers by opening Device Manager and right clicking the entry for JR Programmer and choosing Update Drivers > Browse > My Computer > J-Runner > common > drivers, and choosing the correct driver for your case. | ||
* Some devices have defects: play with the switches and make sure the USB port is soldered on well. | * Some devices have defects: play with the switches and make sure the USB port is soldered on well. | ||
If issues persist, try one of the below fixes. | If issues persist, try one of the below fixes. | ||
===Red Light on JR Programmer/JR Programmer not Detected by | ===Red Light on JR Programmer/JR Programmer not Detected by J-Runner=== | ||
# Put the bottom left switch on the programmer towards JP-BL. | # Put the bottom left switch on the programmer towards JP-BL. | ||
# Plug into PC and open | # Plug into PC and open J-Runner, verify that it says Bootloader Attached. | ||
# In | # In J-Runner: go to Tools > Update jr-p.fw, and browse to the J-Runner folder (in My Computer). Select the commons > PICFLASH* version relevant to your case (v2 if you have a v2, the other for a v1; ignore the ISO version). | ||
# Let it finish reflashing the programmer, then proceed to flip the switch back away from JP-BL and hold the reset button for 5 seconds. Your JR Programmer should work after this. | # Let it finish reflashing the programmer, then proceed to flip the switch back away from JP-BL and hold the reset button for 5 seconds. Your JR Programmer should work after this. | ||
===Unable to start | ===Unable to start J-Runner/.NET Framework errors=== | ||
Make sure you have the correct version of the .NET Framework installed, which is listed in the README file. | Make sure you have the correct version of the .NET Framework installed, which is listed in the README file. | ||
Latest revision as of 20:20, 4 September 2024
The Xecuter JR Programmer is a device used to read/write to Xbox 360 NANDs and program glitch chips. It works in conjunction with the Windows program J-Runner and can be used for JTAG and RGH installs. It also can be used with the Xecuter X360USB PRO device to flash DVD drives.
Drivers and updates for the device can be found within the program J-Runner.
Switches Usage
There are two possible switches on the JR Programmer:
- The
JP-BLswitch is JR Programmer bootloader mode switch. When the switch is set toJP-BL, you can flash new programmer firmware. When the switch is set to the opposite (blank) side, you can read/write to console NANDs. - The
JP-3switch is the glitch chip power switch. When the switch is set toJP-3, the glitch chip will be powered on and ready to be flashed. When the switch is set to the opposite (blank) side, the glitch chip will be powered off. This switch is not present on the original JR Programmer.
Updating Glitch Chip Timing File
- Unplug console power and unplug the mini USB cable from your JR Programmer.
- Set the switch to JTAG-XSVF if not set to that already.
- Plug in the JR Programmer to your computer via the mini USB cable and plug in the glitch chip using the glitch chip programming cables.
- Launch J-Runner, select Advanced > Custom NAND/CR Functions, then choose your XSVF file, and start.
Updating the JR Programmer Firmware
- Unplug the JR Programmer completely and set the switch on the bottom (if the USB slot is on your left) to JP-BL.
- Plug in the JR Programmer to your computer via the USB slot. Ensure J-Runner says "bootloader attached".
- Select Tools > Update JRP FW.
- Navigate to your J-Runner folder > Common, and select the v2 JRP firmware. It will take some time to flash. Once it is done, unplug the JR Programmer and flip the switch at the bottom away from JP-BL and plug it back in. If the LED lights up green, you are done. If not, try unplugging it a few times.
Troubleshooting
General Tips
- Verify all solder points are well done and not bridged. If unsure or think it is badly done, reflow the solder.
- Make sure you are running J-Runner as Administrator (Right click J-Runner > Run as Administrator).
- J-Runner may have issues with Windows 10, either find an older operating system to flash from or try J-Runner with Extras (you must disable driver signing). If you are planning on using an older operating system, you can use Windows 7 or XP in a VM with USB access (make sure to install .NET Framework or J-Runner won't work).
- Reinstall the drivers by opening Device Manager and right clicking the entry for JR Programmer and choosing Update Drivers > Browse > My Computer > J-Runner > common > drivers, and choosing the correct driver for your case.
- Some devices have defects: play with the switches and make sure the USB port is soldered on well.
If issues persist, try one of the below fixes.
Red Light on JR Programmer/JR Programmer not Detected by J-Runner
- Put the bottom left switch on the programmer towards JP-BL.
- Plug into PC and open J-Runner, verify that it says Bootloader Attached.
- In J-Runner: go to Tools > Update jr-p.fw, and browse to the J-Runner folder (in My Computer). Select the commons > PICFLASH* version relevant to your case (v2 if you have a v2, the other for a v1; ignore the ISO version).
- Let it finish reflashing the programmer, then proceed to flip the switch back away from JP-BL and hold the reset button for 5 seconds. Your JR Programmer should work after this.
Unable to start J-Runner/.NET Framework errors
Make sure you have the correct version of the .NET Framework installed, which is listed in the README file.