LaserActive:CLD-A100 Board Photos: Difference between revisions
(Created page with "== SYPS - Power Supply == <gallery> CLDA100_SYPS_Front.jpeg|Power Supply - Component Side CLDA100_SYPS_Rear.jpeg|Power Supply - Solder Side CLDA100_SYPS_SupplementalFuse.jpeg|Power Supply - Supplemental 2A ICP-N50 Fuse for INTF +5V </gallery> == INTF - PAC Interface Board == <gallery> CLDA100_INTF_Front.jpeg|Interface - Component Side CLDA100_INTF_Rear.jpeg|Interface - Solder Side </gallery> == CONT - Mechanism Controller Board == <gallery> CLDA100_CONT_Front.jpeg|...") |
No edit summary |
||
| Line 1: | Line 1: | ||
== SYPS - Power Supply == | == SYPS - Power Supply == | ||
The power supply contains the circuitry for the spindle motor drive in addition to the 5 separate voltage rails (+5v Standby, +5V, -5V, +14V and -14V). There are 3 revisions of the power supply, but the changes are centered around the fuse selection and whether or not there is a supplemental fuse. USA and Japanese players have the same power supply, with the exception of the AC cable. If the SYPS does not have the supplemental fuse, it is highly recommended to add it (https://consolemods.org/wiki/LaserActive:PSU_ICP_Mod). | |||
<gallery> | <gallery> | ||
| Line 8: | Line 10: | ||
== INTF - PAC Interface Board == | == INTF - PAC Interface Board == | ||
INTF contains the mode controller ASIC, EFM decoding, digital audio processing and interface to the PAC port. The large 1200uF capacitor on this board is often leaking and may have corroded the +5V power trace to the PAC port. | |||
<gallery> | <gallery> | ||
| Line 15: | Line 19: | ||
== CONT - Mechanism Controller Board == | == CONT - Mechanism Controller Board == | ||
CONT contains the Mechanism controller and audio amplifiers. Additionally, signals from FTSB to VIDEO are passed through this board via the myriad ribbon cables. It is advised to reflow the solder on the 3 right angle connectors that connect CONT to INTF, as they often develop cracked solder joints and can interrupt communication between INTF and the mechanism controller. | |||
<gallery> | <gallery> | ||
| Line 22: | Line 28: | ||
== FTSB - Focus/Tracking Servo Board == | == FTSB - Focus/Tracking Servo Board == | ||
FTSB performs the RF amplification of the RF waveform from the optical pickup. Additionally, it has the driving circuitry for the focus and tracking coils. This board should have its capacitors replaced, as C835 and C836, near the Focus/Tracking push-pull transistors, often have begun leaking. It is also advised to reflow IC802 and Q815-818, in addition to the power ribbon solder connections to ensure longevity. | |||
<gallery> | <gallery> | ||
| Line 29: | Line 37: | ||
== RGBB - RGB Encoder Board == | == RGBB - RGB Encoder Board == | ||
RGBB contains the circuitry that encodes RGB from the PAC's into composite video and superpositions it with LD video sources, if present (i.e. Mega LD/LDROM2). It also has the character generator DSP for the on-screen display text. | |||
<gallery> | <gallery> | ||
| Line 36: | Line 46: | ||
== VIDEO - Video Processing Board == | == VIDEO - Video Processing Board == | ||
VIDEO has all of the processing circuitry for LD composite video, analog audio demodulation and pre-drive circuitry for the spindle motor, with the remaining drive circuitry located on SYPS. | |||
<gallery> | <gallery> | ||
Revision as of 23:06, 29 September 2024
SYPS - Power Supply
The power supply contains the circuitry for the spindle motor drive in addition to the 5 separate voltage rails (+5v Standby, +5V, -5V, +14V and -14V). There are 3 revisions of the power supply, but the changes are centered around the fuse selection and whether or not there is a supplemental fuse. USA and Japanese players have the same power supply, with the exception of the AC cable. If the SYPS does not have the supplemental fuse, it is highly recommended to add it (https://consolemods.org/wiki/LaserActive:PSU_ICP_Mod).
Power Supply - Component Side
Power Supply - Solder Side
Power Supply - Supplemental 2A ICP-N50 Fuse for INTF +5V
INTF - PAC Interface Board
INTF contains the mode controller ASIC, EFM decoding, digital audio processing and interface to the PAC port. The large 1200uF capacitor on this board is often leaking and may have corroded the +5V power trace to the PAC port.
Interface - Component Side
Interface - Solder Side
CONT - Mechanism Controller Board
CONT contains the Mechanism controller and audio amplifiers. Additionally, signals from FTSB to VIDEO are passed through this board via the myriad ribbon cables. It is advised to reflow the solder on the 3 right angle connectors that connect CONT to INTF, as they often develop cracked solder joints and can interrupt communication between INTF and the mechanism controller.
CONT - Component Side
CONT - Solder Side
FTSB - Focus/Tracking Servo Board
FTSB performs the RF amplification of the RF waveform from the optical pickup. Additionally, it has the driving circuitry for the focus and tracking coils. This board should have its capacitors replaced, as C835 and C836, near the Focus/Tracking push-pull transistors, often have begun leaking. It is also advised to reflow IC802 and Q815-818, in addition to the power ribbon solder connections to ensure longevity.
FTSB - Component Side
FTSB - Solder Side
RGBB - RGB Encoder Board
RGBB contains the circuitry that encodes RGB from the PAC's into composite video and superpositions it with LD video sources, if present (i.e. Mega LD/LDROM2). It also has the character generator DSP for the on-screen display text.
RGBB - Component Side
RGBB - Solder Side
VIDEO - Video Processing Board
VIDEO has all of the processing circuitry for LD composite video, analog audio demodulation and pre-drive circuitry for the spindle motor, with the remaining drive circuitry located on SYPS.
VIDEO - Component Side
VIDEO - Solder Side
