Search results
Jump to navigation
Jump to search
- [[File:Phat360PLLFix.jpg|thumb|400x400px|PLL Repair on a Phat motherboard (required if bottom pad is damaged). Image cre === PLL ===4 KB (608 words) - 22:34, 3 April 2024
- ...ome boards and can take minutes to boot if at all - some randomly crash on PLL de-assertion. R-JTAG requires dashboard 14719, and R-JTOP requires dashboar <sup>7</sup> Requires scraping solder mask off of PLL point (more difficult).6 KB (670 words) - 23:31, 3 May 2024
- ...s (but also works for Non-Xenon Phats), which uses I2C slowdown instead of PLL slowdown, and works on any dashboard. However, it is considered more diffic * RGH1.2 combines RGH1-like PLL slowdown with Glitch2 images to allow reliable glitching of Falcon/Jasper c4 KB (742 words) - 23:31, 3 May 2024
- [[File:Phat360PLLFix.jpg|thumb|PLL Repair on a Phat motherboard (required if bottom pad is damaged)|327x327px] ...s legs, causing less strain to the joint if it moves around. Make sure the PLL wire is not nearby any high noise areas, like capacitors or coils.13 KB (2,296 words) - 08:32, 1 May 2024
- *A - PLL *A - PLL7 KB (1,231 words) - 19:58, 11 March 2024
- RGH1.2 combines RGH1-like PLL slowdown with Glitch2 images to allow reliable glitching of Falcon/Jasper c *A - PLL (5-10K ohm resistor recommended on Slim)14 KB (2,310 words) - 19:14, 16 April 2024
- * RGH 1.2 uses PLL instead of IC2 to slow clock; RGH 2 glitches before eFuse check3 KB (492 words) - 02:55, 30 January 2023
- *A - PLL *A - PLL10 KB (1,748 words) - 23:04, 18 March 2024
- |The Mod Shop||Slim PLL QSB|| [[File:360-PLL-QSB.jpg|300px]]||RGH 1.2/3 QSB13 KB (1,872 words) - 20:16, 13 April 2024
- ...ing GPU or a badly soldered PLL connection (if it is an RGH). Resolder the PLL point if it is an RGH.10 KB (1,763 words) - 06:09, 28 March 2024
- ...send GetPowerUpCause to SMC || Check POST code, Check CPU clock, RST, and PLL circuits, Replace CPU9 KB (1,376 words) - 06:51, 5 April 2024
- ...R-JTAG, the normal version which uses I2C slowdown, and R-JTAG+ which uses PLL slowdown. This should only be used if your console doesn’t work well with9 KB (1,522 words) - 06:34, 13 March 2024
- ...d to solder to are similar to RGH 1.2, aside from using EXT_CLK instead of PLL.9 KB (1,487 words) - 20:01, 11 March 2024
- ...ms, but it also works for non-Xenon Phats. It uses I2C slowdown instead of PLL slowdown, and works on any dashboard. However, it is considered more diffic12 KB (2,049 words) - 20:24, 13 April 2024
- ...performs RGH1.2 V2 on a Trinity after being the first to locate a suitable PLL point under the solder mask. ...performs RGH1.2 V2 on a Corona after being the first to locate a suitable PLL point under the solder mask.40 KB (6,086 words) - 19:54, 20 February 2024
- ...r, creating SMC+, optimizing boots for all motherboards, locating the Slim PLL point, porting RGH1.2 to Trinity/Corona motherboards, and developing EXT_CL13 KB (1,932 words) - 06:08, 17 April 2024
- ...new CGPU while disabling the pins used to slow down the clock speed, like PLL and EXT_CLK. Thus, '''all Winchester motherboards are unmoddable''' '''at t27 KB (4,518 words) - 07:42, 1 May 2024
- |'''PLL VCO'''172 KB (27,570 words) - 19:01, 14 May 2024