Search results

[[File:Phat360PLLFix.jpg|thumb|400x400px|PLL Repair on a Phat motherboard (required if bottom pad is damaged). Image cre === PLL ===

...not possible on Slim consoles, so if your Slim has a glitch chip and uses PLL you have a RGH1.2 install. Phat + Glitch2 + PLL = RGH1.2

...ome boards and can take minutes to boot if at all - some randomly crash on PLL de-assertion. R-JTAG requires dashboard 14719, and R-JTOP requires dashboar ⁷ Requires scraping solder mask off of PLL point (more difficult).

...ome boards and can take minutes to boot if at all - some randomly crash on PLL de-assertion. R-JTAG requires dashboard 14719, and R-JTOP requires dashboar ⁷ Requires scraping solder mask off of PLL point (more difficult).

...s (but also works for Non-Xenon Phats), which uses I2C slowdown instead of PLL slowdown, and works on any dashboard. However, it is considered more diffic * RGH1.2 combines RGH1-like PLL slowdown with Glitch2 images to allow reliable glitching of Falcon/Jasper c

...r, isso se inicializar - alguns travam aleatoriamente na desasserização do PLL. O R-JTAG requer o dashboard 14719, e o R-JTOP requer o dashboard 15572. ⁷ Requer a raspagem da máscara de solda do ponto PLL (mais difícil).

[[File:Phat360PLLFix.jpg|thumb|PLL Repair on a Phat motherboard (required if bottom pad is damaged)|327x327px] ...s legs, causing less strain to the joint if it moves around. Make sure the PLL wire is not nearby any high noise areas, like capacitors or coils.

[[File:J2B1.png|482x482px]][[File:Phat360PLLFix.jpg|thumb|400x400px|PLL Repair on a Phat motherboard (required if bottom pad is damaged). Image cre *A - PLL

RGH1.2 combines RGH1-like PLL slowdown with Glitch2 images to allow reliable glitching of Falcon/Jasper c [[File:Phat360PLLFix.jpg|thumb|400x400px|PLL Repair on a Phat motherboard (required if bottom pad is damaged). Image cre

* RGH 1.2 uses PLL instead of IC2 to slow clock; RGH 2 glitches before eFuse check

*A - PLL *A - PLL

|The Mod Shop||Slim PLL QSB|| [[File:360-PLL-QSB.jpg|300px]]||RGH 1.2/3 QSB

...ing GPU or a badly soldered PLL connection (if it is an RGH). Resolder the PLL point if it is an RGH.

...send GetPowerUpCause to SMC || Check POST code, Check CPU clock, RST, and PLL circuits, Replace CPU

...R-JTAG, the normal version which uses I2C slowdown, and R-JTAG+ which uses PLL slowdown. This should only be used if your console doesn’t work well with

...d to solder to are similar to RGH 1.2, aside from using EXT_CLK instead of PLL.

...ms, but it also works for non-Xenon Phats. It uses I2C slowdown instead of PLL slowdown, and works on any dashboard. However, it is considered more diffic

...r, creating SMC+, optimizing boots for all motherboards, locating the Slim PLL point, porting RGH1.2 to Trinity/Corona motherboards, and developing EXT_CL

...performs RGH1.2 V2 on a Trinity after being the first to locate a suitable PLL point under the solder mask. ...performs RGH1.2 V2 on a Corona after being the first to locate a suitable PLL point under the solder mask.

...new CGPU while disabling the pins used to slow down the clock speed, like PLL and EXT_CLK. Thus, '''all Winchester motherboards are unmoddable''' '''at t