Comparison of Game Consoles by Sound Capabilities: Difference between revisions

From ConsoleMods Wiki
Jump to navigation Jump to search
Line 151: Line 151:
|align="left"| Internal/Chassis-mounted
|align="left"| Internal/Chassis-mounted
|align="left"| Internal/Chassis-mounted
|align="left"| Internal/Chassis-mounted
|align="left"| The Odyssey 4305 is a 19” television (based on the chassis of the Magnavox T991 television) but with a built-in Odyssey. The device uses a chassis-mounted isolation transformer with no external brick (standard plug coming out the back).  
|align="left"| The Odyssey 4305 is a 19” television (based on the chassis of the Magnavox T991 television) but with a built-in Odyssey. As with most CRTs of this era, the sound was an analog signal produced from small speakers installed inside the chassis. It produced sound in mono and action sounds were similar to other Odyssey series consoles.  
|-
|-
| [[Odyssey:Odyssey_Series_Wiki|Magnavox Odyssey 2000]]
| [[Odyssey:Odyssey_Series_Wiki|Magnavox Odyssey 2000]]

Revision as of 18:13, 30 October 2022

The purpose of this article is to categorize video game consoles according to their supported audio formats, and to consolidate advice on optimizing sound reproduction for each of those consoles.

Exclamation-triangle-fill.svgDRAFT (WORK IN PROGRESS ARTICLE - PLEASE DO NOT RELY ON THE INFORMATION BELOW UNTIL MARKED AS COMPLETED)


[1][2][3][4][5][6][7].

Explanation of Terms

Console:

An asterisk symbol (*) beside a console's name means that a Triad brand replacement power supply is available for that console. See the Triad Power Supplies page for more information.

Voltage:

Generally speaking, the "Voltage" figure on the power supply should match the official specs (below) as closely as possible. There will be exceptions to this rule, and they will be highlighted in the "Notes" column.

Amps:

As amperage refers to potential current (and the device will only draw as much as required) - the A (or the mA) figure may be higher than what the console requires to operate, but should not be lower.

The figures below do not account for additional power draw caused by various modifications, flashcart devices, wireless controllers or similar after-market additions.

Polarity:

The power supply's connector can be center-positive (C+) or center-negative (C-). They can be distinguished by the symbols which can be found, usually either on the power brick, or on the plug.


Polarity symbol.png

Centre-positive symbol


Centre negative.png

Centre-negative symbol


To avoid damage to the console, the user should inspect the symbol on their power supply and ensure that its polarity matches the polarity of the corresponding console (see table below).


Original PN:

The part number for the original stock power supply for a given console.


Replacement PN:

The part number for the recommended replacement power supply for that console.


Connection:


Power Supply:

Note that if the "Power Supply" column says "Internal", then that particular console has an internal power supply module that will perform a similar function to the external "power bricks" used by most retro consoles. If your console's power supply is "internal", the user just needs to find a cable that has the correct electrical plug for your region and also has the matching console-facing connector. This will often be a Figure-8 cable, but a guide to common connectors can be found here and on the IEC 60320 Wikipedia page. The user should also ensure that the console's internal power supply is rated for the AC coming out of their wall. If your console's internal power supply does not match your country's AC voltage (for example, a North American gamer using a European Dreamcast), then step-up/step-down transformers to go up/down in voltage for the target device may be a good option.


Notes:

Any exceptions to the above guidelines, or idiosyncrasies related to an individual console, should be laid out in the "Notes" column. For example, there are exceptions to the rule that voltage on a replacement should be as close as possible to the voltage on the original power supply. The Sega Genesis for instance, uses a 7805 voltage regulator to step the input down from 9V to 5V. The 7805 expects a minimum voltage of 6.5V - the significance of this is that a Genesis 2 (whose original power supply outputs 10V) will work fine with a 9V power supply.

First generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Magnavox Odyssey Magnavox Odyssey.png Output: 9V DC 400 mA Tip positive ? ? 2.5 mm TS jack ? The console cannot generate audio.
Magnavox Odyssey 100 Magnavox odyssey 100.jpg Output: 9V DC 200 mA ? PIDB-15 ? 3.5 mm TS jack ? The console didn't send audio to the tv, instead using an internal piezzo beeper which emitted primitive action sounds through a built-in speaker - for example, a "blip" when the tennis ball is hit by a player's paddle, or when the hockey puck hits the borders of the playing area.
Magnavox Odyssey 200 Magnavox-Odyssey-200-power-supply.jpeg OUTPUT 9V AC 100ma ? ? ? ? ? The console's piezzo beeper operated in the same manner as the Odyssey 100. The Odyssey 200 added an extra game called SMASH (i.e. squash); the buzzer would bleep whenever the ball hit the front "wall".
Magnavox Odyssey 300 Odyssey-300.jpg OUTPUT 9V DC 100ma ? ? ? ? ? As before, the game audio (little more than a few bleeps and bloops) emanates from a speaker in the Odyssey itself, rendering it uncapturable via conventional means.
Magnavox Odyssey 400 Odyssey 400 power supply.jpeg OUTPUT 9V DC 100ma ? ? ? ? ? Console is powered by either six "C" batteries or a 9 volt AC adapter.
Magnavox Odyssey 500 Magnavox-Odyssey-500-power-supply.jpeg Output 9 volts ? ? ? ? ? ? Console is powered by either six "C" batteries or a 9 volt AC adapter.
Magnavox Odyssey 4305 Odyssey 4305 (1 of 8).JPG ? ? ? 701479-4 (AC/DC Power Assembly) Unknown Internal/Chassis-mounted Internal/Chassis-mounted The Odyssey 4305 is a 19” television (based on the chassis of the Magnavox T991 television) but with a built-in Odyssey. As with most CRTs of this era, the sound was an analog signal produced from small speakers installed inside the chassis. It produced sound in mono and action sounds were similar to other Odyssey series consoles.
Magnavox Odyssey 2000 Magnavox-Odyssey-2000-FL.jpg ? ? ? ? ? ? ? Console is powered by either six "C" batteries or a 9 volt AC adapter.
Magnavox Odyssey 3000 Magnavox-Odyssey-3000-power-supply.jpeg OUTPUT 9 volts 78mA ? ? ? ? ? Console is powered by either six "C" batteries or a 9 volt AC adapter.
Magnavox Odyssey 4000 Magnavox Odyssey 4000.jpg OUTPUT 9V DC 100 mA ? ? ? ? ? Unlike most Odyssey models, the AC adapter is necessary as the console does not use batteries.
Philips Odyssey 200 Philips ODYSSEY200 Konsole.jpg ? ? ? ? ? ? ? European release of Magnavox Odyssey 200. Unclear if batteries can be used (TBC)
Philips Odyssey 2001 Philips Odyssey 2001.png 18,6V- 120mA ? FW3009 ? ? ? Unlike most Odyssey models, the AC adapter is necessary as the console does not use batteries.
Philips Odyssey 2100 Philips Odyssey 2100.jpg ? ? ? ? ? ? ? Unlike most Odyssey models, the AC adapter is necessary as the console does not use batteries.
TV Tennis Electrotennis (Epoch) Epoch-electrotennis-battery-compartment.png ? ? ? ? ? ? ? Console is completely wireless; powered by four D size batteries.
Atari Home Pong (Model C-100) Atari-Home-Pong-power-options.jpeg 5.5V DC 100 mA ? 004720 ? ? External PSU Console can be powered by four "D"-size batteries, or an AC adapter (“battery eliminator”)
Atari Super Pong (Model C-140) Ataripong.jpg OUTPUT 6V DC ? ? ? ? ? External Power Supply Unit (6V) The console had a speaker built into the main unit, that could output a simple "bloop" noise every time the ball was hit.
Coleco Telstar Original-Coleco-Telstar-power-supply.jpeg OUTPUT 9V DC 100mA ? Model 6041 ? ? ? Console is powered by either six "C" batteries or a 9V adapter.
Coleco Telstar Classic Original-Coleco-Telstar-power-supply.jpeg OUTPUT 9V DC 100mA Polarity unknown but the Atari 2600 adapter tends to be compatible. Model 6041 ? Typically the tip is positive but in some units, the polarity can be reversed and the unit may need repairs following a blown transistor. ? Unusually for this series, the console doesn’t use batteries. The adapter is 100mA and outputs 3 watts at 60hz.
Coleco Telstar Deluxe Output 9 volts ? ? ? ? ? ? Console verified to operate off either a 9V adapter or six C-Cell batteries. Other details TBD
Coleco Telstar Ranger Original-Coleco-Telstar-power-supply.jpeg OUTPUT 9V DC 100 mA ? Model 6041 ? ? ? Console is powered by either six "C" batteries or a 9V adapter.
Coleco Telstar Alpha Coleco-Telstar-Alpha-power-supply.jpeg OUTPUT 9V DC 100 mA ? Model 6041 ? ? ? Console is powered by either six "C" batteries or a 9V adapter.
Coleco Telstar Colormatic Colormatic-power-supply.jpeg OUTPUT 9V DC 200 mA ? ? ? ? ? ?
Coleco Telstar Regent Coleco-Telstar-Regent-power-options.jpeg OUTPUT 9V DC 200mA ? ? ? ? ? ?
Coleco Telstar Sportsman Output 9 volts ? ? ? ? ? ? Confirmed that console operates off batteries (size undetermined) and a 9V adapter. A standard Atari 2600 adapter will work. More details TBD
Coleco Telstar Combat! Coleco-Telstar-Combat-power-supply.jpeg OUTPUT 9V DC 200mA ? ? ? ? ? Console verified to run via six c-cell batteries or 9V adapter.
Coleco Telstar Colortron Colortron-power-supply.jpeg ? ? ? ? ? ? ? ?
Coleco Telstar Marksman Coleco-Telstar-Marksman-power-supply.jpeg OUTPUT 9V DC 200mA ? ? ? ? ? ?
Coleco Telstar Galaxy Coleco-Telstar-Gemini-power.jpeg OUTPUT 9V DC 200mA ? Model 6041 ? ? ? Confirmed that working AC adapter outputs 3W; unsure whether console has a battery compartment (TBD)
Coleco Telstar Gemini Coleco-Telstar-Gemini-power.jpeg OUTPUT 9V DC 200mA ? ? ? ? ? Console does not have a battery compartment. Verified to work with slightly different “3W” version of the 6041-200ma Telstar AC adapter.
Coleco Telstar Arcade Coleco-Telstar-arcade-power-supply.jpeg OUTPUT 9V DC 200 mA ? Model 6041-200ma ? ? ? Possibly could also be powered by D-size batteries (unconfirmed)
Nintendo Color TV - Game 6 Nintendo-Color-TV-Game-6.jpeg OUTPUT 9V DC ? ? ? ? ? ? ?

Second generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Atari 2600 Atari-2600.png 9V DC 500 mA Tip positive CO10472 ? 3.5 mm TS jack External Different styles of this AC adapter exist, but all have the same specs and part number
Magnavox Odyssey 2 9V AC-12V AC, depending on PSU 400 mA-830 mA, depending on PSU N/A ? ? 3.5 mm TS jack (early models) or 5.5 x 2.1 mm barrel jack (later models) External Multiple revisions of the Odyssey 2 AC adapter exist, each with slightly different voltage and current ratings
Philips Videopac G7000 (European release of Odyssey 2) Philips Videopac G7000 power supply.jpeg OUTPUT 9V DC 1.3 A ? FW3300 ? ? ? External
Mattel Intellivision Input: 120V AC; Output: 5V DC, 12V DC, 16V DC (unregulated), -2.1V DC ? N/A, power cord to electrical outlet is hardwired ? ? N/A Internal The ribbon cable that connects the power supply to the motherboard is extremely fragile, be very careful!
Mattel Intellivision II 16.7V AC 1 A N/A 5872-9629 ? 5.5 x 2.5 mm barrel jack External A variation exists with slightly lower output voltage and current ratings (16.2V AC and 955 mA)
Coleco ColecoVision Colecovisionpsu.png 5V DC, -5V DC, 12V DC 0.9 A (5V), 0.1 A (-5V), 0.3 A (12V) N/A, connector is keyed 55416 N/A Rectangular four-pin connector, same as used by the TI-99/4A computer (though not the same pinout!) External
Atari 5200 (Four controller port model) * Atari-5200.png 11.5V DC 1.95 A Tip positive C018187 WSU090-2000-13 5.5 x 2.5 mm barrel jack External The four-port Atari 5200 had an interesting "one cable" design where both the RF signal and the power ran through one coaxial cable which was permanently attached to the system. A power mod is available that allows the console to use a conventional switch box or direct RF adapter.
Atari 5200 (Two controller port model) * Atari-5200.png 9.3V DC 1.95 A Tip positive C018187 WSU090-2000-13 5.5 x 2.5 mm barrel jack External
GCE/MB Vectrex Vectrex rear view.jpeg ? ? N/A, power cord to electrical outlet is hardwired ? ? N/A Internal


Third generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Nintendo Entertainment System (US) * NES.png 9V AC 1.2 A N/A NES-002 WSU090-1300 or WSU090-1300-R 5.5 x 2.1 mm barrel jack External The NES will accept a DC power supply so long as the voltage and current are within spec
Nintendo Entertainment System (PAL) * 9V AC 1.2 A N/A NES-002 WSU090-1300-13 or WSU090-1300-R13 5.5 x 2.5 mm barrel jack External The NES will accept a DC power supply so long as the voltage and current are within spec
Famicom * Famicom.png 10V DC 850 mA Tip negative HVC-002 WSU090-1300-R 5.5 x 2.1 mm barrel jack External Applies to both original and AV Famicom models
Famicom Disk System * DiskSystem.png 9V DC 400 mA Tip negative HVC-025 WSU090-1300-R 5.5 x 2.1 mm barrel jack External or six internal C-cell batteries With a splitter it should be possible to run both a Famicom and Disk System from a single AC adapter without batteries; the WSU-090-2000-R is recommended for this
Twin Famicom * TurboTwinFamicom.png 7.6V DC 1.25 A Tip positive UADP-0041CEZZ WSU075-1500-13 5.5 x 2.5 mm barrel jack External Please note that the Twin Famicom's power circuitry is very sensitive to input voltage, anything higher than 7.6V causes the power transistor to run very hot
Sega SG-1000 * SG-1000.png 9V DC 850 mA Tip negative SA-150 WSU090-1300-R 5.5 x 2.1 mm barrel jack External
Sega Mark III * MarkIII.png 9V DC 850 mA Tip negative SA-150 WSU090-1300-R 5.5 x 2.1 mm barrel jack External
Sega Master System * SMS.png 9V DC 1 A Tip negative 3025 WSU090-1300-R 5.5 x 2.1 mm barrel jack External Different styles of this AC adapter exist, but all have the same specs and part number
Atari 7800 Atari-7800.png 9V DC 1 A N/A, connector is keyed CO24471-001 ? Two-pin keyed connector External Different styles of this AC adapter exist, but all have the same specs and part number
Casio PV-1000 * Pv1000psu.png 15V DC 500 mA Tip negative AD-4815 WSU150-0560-R 5.5 x 2.1 mm barrel jack External
Epoch Super Cassette Vision * 8.5V DC 800 mA Tip negative N/A WSU090-1300-R 5.5 x 2.1 mm barrel jack External
Amstrad GX4000 * 11V DC 500 mA Tip positive GX4000PSU/UK (UK), GX4000PSU/E (EU) WSU090-1300 5.5 x 2.1 mm barrel jack External

Fourth generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
NEC TurboGrafx 16 * TurboGrafx16.png 10.5V DC 730 mA Tip negative HES-ACA-01 WSU090-1300-R 5.5 x 2.1 mm barrel jack External
PC Engine * PC-Engine.png 9V DC 650 mA Tip negative PAD-105/PAD-106 WSU090-1300-R 5.5 x 2.1 mm barrel jack External Same information also applies to both Core Grafx models and the PC Engine Shuttle
NEC PC Engine CD * 9V DC 1.45 A Tip negative AD-IF30/AD-IF30A WSU090-2000-R13 5.5 x 2.5 mm barrel jack External Note that this is for the IFU-30 interface; the CD player portion (CDR-30) uses the same AC adapter as the PC Engine console when used as a standalone CD player
NEC TurboGrafx-CD * TurboGrafxCD.png 11V DC 1.53 A Tip negative HES-ACA-02 WSU120-2000-R13 5.5 x 2.5 mm barrel jack External Note that this is for the dock; the CD player portion (HES-CDR-01) uses the same AC adapter as the TG-16 console when used as a standalone CD player. Also note that the TG-CD dock will not power up properly with anything less than 10V, and the CD player will not read discs when docked
NEC SuperGrafx SuperGrafx.png 9V DC 800 mA Tip positive PAD-113 ? 6.3 x 3.0 mm barrel jack External
NEC TurboExpress/PC Engine GT TurboExpress.png 7V DC 700 mA Tip positive HES-ACA-04 (US), PAD-121 (JP) ? 3.5 x 1.35 mm barrel jack External or six internal AA-cell batteries
NEC TurboDuo/PC Engine Duo TurboDuo.png 10V DC 1 A Tip positive HES-ACA-05 (US), PAD-124 (JP) ? 6.3 x 3.0 mm barrel jack External NEC also released an external battery pack for the Duo in Japan only
NEC Super CD-ROM2 12V DC 1 A Tip positive PAD-125 ? 6.3 x 3.0 mm barrel jack External The Super CD-ROM2 also has a jumper cable which passes through power to the connected PC Engine console. This cable plugs into a 3.5 mm x 1.35 mm barrel jack on the Super CD and then into the power jack on the PC Engine.
NEC PC Engine LT 9V DC 700 mA Tip positive PAD-127 ? ? External ?
NEC PC Engine Duo-R/Duo-RX DuoR.png 9V DC 1 A Tip positive PAD-129/PAD-130 ? EIAJ-03 barrel jack External
Sega Genesis (model 1) * 9V DC 1.2 A Tip negative MK-1602 WSU090-1300-R 5.5 x 2.1 mm barrel jack External
Sega Mega Drive (model 1) * Genesis Model 1.png 9V DC 1.2 A Tip negative SA-160 (JP) WSU090-1300-R 5.5 x 2.1 mm barrel jack External
Sega Genesis (model 2) Genesis Model 2.png 10V DC 850 mA Tip positive MK-2103 (US), SA-190 (JP) ? EIAJ-03 barrel jack External
Sega Genesis 3 Genesis Model 3.png 10V DC 300 mA Tip positive MK-1479 ? EIAJ-03 barrel jack External
Sega Mega Jet 10V DC 850 mA Tip positive SA-190 ? EIAJ-03 barrel jack External ?
Sega Genesis Nomad Sega Nomad.png 10V DC 850 mA Tip positive MK-2103 ? EIAJ-03 barrel jack External or six AA-cell batteries via clip-on pack or rechargeable battery via clip-on pack ?
Sega 32X Sega 32X.png 10V DC 850 mA Tip positive MK-2103 (US), SA-190 (JP) ? EIAJ-03 barrel jack External Exactly the same as the model 2 Genesis/Mega Drive
Sega/Victor Wondermega RG-M1 9.5V DC 1.5 A Tip positive AA-S95 ? EIAJ-03 barrel jack External
Sega CDX Sega CDX.png 9.5V DC 1.5 A Tip positive MK-4122 ? EIAJ-03 barrel jack External Do not use the MK-2103 AC adapter as it does not supply enough current
JVC X'Eye/Victor Wondermega RG-M2 9.5V DC 1.5 A Tip positive AA-S95 (JP), AA-S95J (US) ? EIAJ-03 barrel jack External Same specs as the CDX AC adapter; as with the CDX do not use the MK-2103 AC adapter as it does not supply enough current
Sega Game Gear * Game Gear.png 9V DC (JP/EU), 10V DC (US) 850 mA or 1.2 A (JP), 850 mA (US), 1.2 A (EU) Tip negative (EU/JP), tip positive (US) SA-150 or SA-160 (JP), 2103/MK-2103 (US), 1605 (EU) WSU090-1300-R (EU/JP) 5.5 x 2.1 mm barrel jack (EU/JP), EIAJ-03 barrel jack (US) External or six internal AA-cell batteries European and Japanese Game Gears use the same AC adapter as the model 1 Mega Drive, whereas (for some reason) US models use a different AC adapter which was later used for the model 2 Genesis/Mega Drive
Nintendo Game Boy Game Boy.png 4.8V DC 150 mA Tip negative DMG-003 ? ? External or four internal AA-cell batteries Also doubles as a rechargeable battery pack
Nintendo Game Boy Pocket Game Boy Pocket.png 3V DC 300 mA Tip positive MGB-005 ? ? External or two internal AAA-cell batteries ?
Super Nintendo (US) SNES.png 10V DC 850 mA Tip negative SNS-002 ? 6.9 mm x 4.1 mm barrel jack with 0.7 mm inner pin External
Super Famicom * Super Famicom.png 10V DC 850 mA Tip negative HVC-002 WSU090-1300-R 5.5 x 2.1 mm barrel jack External Exactly the same as the original Famicom
Super Nintendo (PAL) * 9V AC 1.2 A Not applicable NES-002 ? 5.5 x 2.5 mm barrel jack External Exactly the same as the PAL NES; the PAL SNES has a charge pump circuit which generates 12V DC for SCART autoswitching, hence the use of an AC power supply
SNK Neo Geo AES * 5V DC (PRO-POW models only), 10V DC (PRO-POW3/E models only) 3 A (5V), 1 A (10V) Tip negative PRO-POW (5V) NEO-POW3 (10V) WSU050-3000-R (5V), WSU090-1300-R (10V) 5.5 x 2.1 mm barrel jack External Older AES consoles used a regulated 5V DC AC adapter while newer models had an unregulated 10V supply. Be *very* careful!
SNK Neo Geo CD Neo-Geo-CD.jpeg 5V DC, 12V DC 2 A (5V), 1 A (12V) N/A, connector is keyed POWCD-J (JP) N/A Three-pin connector, same as found on some Panasonic and Sony MSX2 models (though not the same pinout!) External ?
Pioneer LaserActive LaserActive.png Input: 100V AC (JP), 120V AC (US) ? N/A, power cord is hardwired N/A N/A N/A Internal ?

Fifth generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Commodore Amiga CD32 5V DC, 12V DC ? N/A ? ? 4-pin DIN External ?
Panasonic 3DO Panasonic 3DO FZ-1.png ? ? ? ? ? ? ? ?
Atari Jaguar * Atari-Jaguar.png 9V DC 1.2 A Tip negative 500273/PP-912 WSU090-1300-R 5.5 x 2.1 mm barrel jack External
Atari Jaguar CD * 9V DC 1.2 A Tip negative 500273/PP-912 WSU090-1300-R 5.5 x 2.1 mm barrel jack External Exactly the same as the Jaguar itself
Bandai Playdia * 9V DC 850 mA Tip positive BA-002 WSU090-1300 5.5 x 2.1 mm barrel jack External
Sega Saturn Saturn Model 1.png ? ? N/A ? ? C7 Internal North American consoles have a polarized connector
Sony PlayStation PS1.png ? ? N/A ? ? C7 Internal North American consoles have a polarized connector
Sony PSone PSOne.png 7.5V DC 2 A Tip positive SCPH-112 (JP), SCPH-113 (US), SCPH-114 (EU), SCPH-115 (UK) ? EIAJ-03 barrel jack External Do not use a PS2 slim AC adapter!
NEC PC-FX Input: 100V AC ? N/A, power cord is hardwired ? N/A N/A Internal
Casio Loopy 24V DC 1 A Tip positive AD-2410J ? 5.5 x 2.5 mm barrel jack External ?
Apple Pippin Input: 100-240V AC ? N/A ? N/A C14 Internal
Nintendo 64 N64.png 3.3V DC, 12V DC 2.7 A (3.3V), 0.8 A (12V) N/A, entire power supply is designed to only fit one way into the console itself NUS-002 ? Proprietary connector External

Sixth generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Game Boy Advance Game Boy Advance.png 3.3V DC 350 mA N/A, connector is molded to only fit one way into the system AGB-009 ? N/A, fits into battery bay External or two internal AA-cell batteries The original GBA does not have a dedicated AC adapter input like other Game Boy systems, all external AC adapters use the battery terminals
Game Boy Advance SP Game Boy Advance SP.png 5.2V DC 320 mA N/A, connector is keyed AGS-002 Unofficial 5 V USB cables Proprietary connector External
Game Boy Micro Game Boy Micro.png 5.2V DC 320 mA N/A, connector is keyed OXY-002 Unofficial 5 V USB cables Proprietary connector External
Sega Dreamcast Dreamcast.png Input: 100V AC (JP), 120V AC (US), 220/240V AC (EU/UK); Output: 3.3V DC, 5V DC, 12V DC ? ? ? N/A C7 Internal North American consoles have a polarized connector
Sony PlayStation 2 (original) PS2.png ? ? ? ? ? C7 Internal North American consoles have a polarized connector
Sony PlayStation 2 (slim, SCPH-7xxxx) PS2 Slim.png Input: 100V-240V AC; Output: 8.5V DC Input: 1.5 A, Output: 5.65 A Tip positive SCPH-70100 ? EIAJ-03 barrel jack External
Sony PlayStation 2 (slim, SCPH-9000x) PS2 Slim 2.png Input: 100-240V AC; Output: 7.5V DC Output: 4.5 A N/A ? ? C7 non-polarized Internal Power supply is multivoltage despite what is indicated on the outside of the console
VM Labs Nuon File:Nuon-N2000-wController-L.jpg Input: 120V AC ? N/A, power cord is hardwired ? ? N/A Internal ?
Microsoft Xbox Xbox.png ? ? ? ? ? C7 non-polarized Internal
Nintendo GameCube GameCube.png 12V DC 3.25 A N/A, connector is keyed DOL-002 ? Proprietary connector External

Seventh generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Nintendo DS DS.png 5.2 V DC 320 mA N/A, connector is keyed AGS-002 Unofficial 5 V USB cables Proprietary connector External Same as GBA SP except for console name removed from sticker
Nintendo DS Lite DS-Lite.png 5.2 V DC 450 mA N/A, connector is keyed USG-002 Unofficial 5 V USB cables Proprietary connector External Resembles Mini-USB B to the point a mangled connector can be directly and "correctly" connected
Nintendo DSi series DSi XL.png 4.6 V DC 900 mA N/A, connector is keyed WAP-002 Still unofficially USB compatible Proprietary connector External Originally invented for Nintendo/Buffalo WAP-001 Wi-Fi access point
Sony PSP (except N1000/Go) PSP.png 5 V DC EP: 1500 mA, LP: 2000 mA Negative ground PSP-100 (two piece), PSP-103 (fixed cable) Third party USB-based cables; official USB charging (if console can boot, not on 1000 series) EIAJ-02 (4.0/1.7 mm barrel) External
Sony PSP-N1000 series (Go) 5 V DC 1500 mA USB-A PSP-N100 (laptop style three piece), PSP-N104 (wall wart two piece) PC/generic USB power supply? Electrically USB-A, but in recessed position requiring a long and specially notched plug External
Nintendo Wii Wii.png 12V DC 3.7 A N/A, connector is keyed RVL-002 ? Proprietary connector External
Microsoft Xbox 360 (Xenon/Zephyr) Xbox 360.png Output: 12V DC, 5V DC 16.5 A (12V), 1 A (5V) N/A, connector is keyed DPSN-186CB-1A ? Proprietary connector with central and overline tabs External Forwards compatible
Microsoft Xbox 360 (Falcon/Opus) Output: 12V DC, 5V DC 14.2 A (12V), 1 A (5V) N/A, connector is keyed ? ? Proprietary connector with overline tab External Forwards compatible
Microsoft Xbox 360 (Jasper/Kronos) Output: 12V DC, 5V DC 16.5 A (12V), 1 A (5V) N/A, connector is keyed ? ? Proprietary connector with split overline tabs External
Microsoft Xbox 360 S Xbox 360 S.png Output: 12V DC, 5V DC 9.6 A (12V), 1 A (5V) N/A, connector is keyed PB-2121-03MX ? Proprietary double barrel jack connector External ?
Microsoft Xbox 360 E Xbox 360 E.png Output: 12V DC, 5V DC 9.6 A (12V), 1 A (5V) N/A DCGP FJ-1 ? Proprietary barrel jack connector External ?
Sony PlayStation 3 PS3-Fat.png Input: 100V-240V AC (most models), 220V-240V AC (early PAL models) ? ? ? ? C14 (original models), C7 non-polarized (Slim and Super Slim models) Internal Detailed information can be found here.
Sony PlayStation 3 standard controller/keyboard/headset 5 V 2x 500 mA USB-A CECHZA1 PS3 console, compatible (handshaking) USB hosts C7 to two USB-A External
Sony PlayStation 3 Move controller 5 V ? ? CECH-ZCC1 ? Barrel jack, unspecified External

Eighth generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Nintendo 3DS/2DS Series incl. New 4.6 V DC 900 mA N/A, connector is keyed WAP-002 Still unofficially USB compatible Proprietary connector External Eventually replaced with cost-cutting revision (thinner cable)
Sony PS Vita Vita.png 5 V DC 1 A (?) USB-A PCH-ZAC1 Official USB charging Electrically USB-A, but in recessed position requiring a long and specially notched plug External Connects to model specific data cable (1000 series: proprietary, 2000 series: micro-USB B)
Sony PS Vita TV PSTV.png 5 V DC 2000 mA Negative ground PDEL-100 PSP power bricks and their equivalents EIAJ-02 (4.0/1.7 mm barrel) External Recycled from developer Vita
Nintendo Wii U Wii U.png 15V DC 5 A N/A, connector is keyed WUP-002 ? Proprietary connector External Connector is very similar to the original Wii but is not compatible (colored yellow for identification). Unofficially[8] multivoltage.
Nintendo Wii U GamePad 4.75 V DC 1.6 A N/A, connector is keyed WUP-011 Still unofficially USB compatible Proprietary connector External Just barely enlarged 2/3DS/i/XL connector. Unofficially multivoltage.
Sony PlayStation 4 (original) PS4.png Input: 100-240V AC ? ? ? ? C7 non-polarized Internal
Sony PlayStation 4 (slim) PS4 Slim.png Input: 100-240V AC ? ? ? ? C7 non-polarized Internal
Sony PlayStation 4 Pro PS4 Pro.png Input: 100-240V AC ? ? ? ? C17 (CUH-7000 and -7100 models), C7 non-polarized (CUH-7200 models) Internal
Microsoft Xbox One Xbox One.png Input: 100-127V AC (JP/US), Output: 12V DC, 5V DC 16.5 A (12V), 1 A (5V) PB-2201-02MX ? ? Proprietary connector, same as the 360 S External
Microsoft Xbox One S Xbox One S.png Input: 100-240V AC ? ? ? ? C7 non-polarized Internal
Microsoft Xbox One X Xbox One X.png Input: 100-240V AC ? ? ? ? C7 non-polarized Internal
Nintendo Switch Input: 100-240V AC, Output: 5V DC, 15V DC 1.5A (5V), 2.6A (15V) N/A, connector is reversible HAC-002 ? USB-C External Not fully USB-PD compliant. Compatible 15V power supply required for dock.

Ninth generation of consoles

Console Pictures Voltage Amps Polarity Original PN Replacement PN Connection Power Supply Notes
Sony PlayStation 5 ? ? ? ? ? C7 non-polarized Internal
Microsoft Xbox Series S ? ? ? ? ? C7 non-polarized Internal
Microsoft Xbox Series X ? ? ? ? ? C7 non-polarized Internal

References

  1. ↑ https://shmup.fandom.com/wiki/Tate_Mode
  2. ↑ https://www.doesitflip.com/
  3. ↑ https://shmups.system11.org/viewtopic.php?f=1&t=60868
  4. ↑ https://store.steampowered.com/curator/14416124/
  5. ↑ https://retronauts.com/article/946/the-comprehensive-list-of-flip-grip-friendly-vertical-games-for-switch
  6. ↑ http://www.gamepilgrimage.com/content/games-tate-mode-standard-definition
  7. ↑ https://www.reddit.com/r/NintendoSwitch/comments/85fqso/list_of_switch_games_that_support_nonstandard/
  8. ↑ [1]
Retrieved from "https://consolemods.org/wiki/index.php?title=Comparison_of_Game_Consoles_by_Sound_Capabilities&oldid=18143"