Xbox 360:JTAG

From ConsoleMods Wiki
Revision as of 13:40, 6 September 2023 by Nadaman (talk | contribs) (The formatting of the page is now more consistant with the RGH pages)
Jump to navigation Jump to search
Exclamation-triangle-fill.svgThe steps on this page are considered risky for your console, as there is a chance you can brick it. Please have someone else mod your console if you are not experienced in soldering!


The JTAG (aka SMC) hack was the first permanent modification that allows you to run unsigned code, mods, game backups, and homebrew on your phat console. The hack relies on vulnerabilities in the CB bootloader, which are only present on dashboards 7371 and lower. If you are on a higher dashboard, take a look at the recommended exploit chart and see what hack is right for you.

Note that this guide is a condensation of multiple JTAG guides, most notably the oblivioncth's Xbox 360 Ultimate Exploit Guide[1], Xecuter's JTAG guide[2], M AzeeM K's Alternate JTAG guide[3], X-Splinter's Matrix USB Flasher guide[4], as well as personal experience.

While it's recommended to read through this guide in its entirety, a video guide for JTAG can be found on MrMario2011's channel[5].

Note that JTAG does not support Slim/E motherboards.

Requirements

Xbox 360 Motherboard Identifcation Chart

Below are the requirements to JTAG your Xbox 360. It's recommended to read ahead and choose the NAND dumping method and JTAG-specific wiring method that's right for you, as you will need more equipment or a NAND programmer depending on the method you choose.

To check if your console is exploitable, you must have:

  1. A fat console (Xenon, Zephyr, Falcon, Opus, or Jasper model). You can look at the back of your console and check the motherboard identification chart to find out what model you have.
    • If you have a Jasper, determine whether if there is Memory Unit built in. If it has 214MB of storage, it's a 256MB NAND. If it has 451MB of storage, it is a 512MB NAND.
  2. Your console on dashboard 7371 or lower. If you are on the original blades dashboard, that is sufficient. Otherwise, you can check this by navigating to Settings > Console Settings > Hover over System Info. Your dashboard version will be shown in the top right in the form 2.0.xxxxx.0, where xxxxx is your dashboard version.
    • If it is on dashboard 7371, the system may not be JTAGable. You can only find out by dumping your NAND.
  3. Soldering experience. The Xbox 360 is not a good place to learn to solder. Regardless of which dumping method you choose, you will need a soldering iron, solder, and flux.

Equipment Needed

  • A soldering iron, solder, flux, and Isopropyl alcohol with cotton swabs**Specific recommendatons can be found on this page
  • 28-30 AWG Wire (Solid core recommended)
  • Two 1N914/4148 switching diodes
  • Wire Insulation (kapton tape, electrical tape, heatshrink, etc.) for the diodes
  • A PC running Windows Vista or later
  • J-Runner with Extras
  • Any compatible NAND Programmer (Listed below)
  • NAND Backup with XeLL written to the console (Listed below)

Reading your NAND

There are six different methods to making a dump of your NAND chip: xFlasher 360, Nand-X, JR Programmer, PicoFlasher, Matrix USB NAND Flasher, or a LPT cable. Consider the pros and cons below and choose the method that’s right for you. Once you have decided on a method, select the guide below and follow it to get a NAND dump, patch the dump, and write the dump to your motherboard. Once you’ve successfully backed up your NAND and wrote XeLL to it, continue to the next section.

Tutorial for backing up and writing XeLL to the NAND

Device Pros Cons
xFlasher 360
  • Reads NAND fast in 40 seconds to 4 minutes
  • Can also program glitch chips
  • Actively supported
  • Doesn't require unsigned drivers
  • USB-C
  • Most expensive flasher
  • Can't be used for flashing Sonus Sounds
Nand-X
  • Reads NAND in 2-8 minutes
  • More expensive than most NAND flashers
  • Not much cheaper than the xFlasher
  • Requires unsigned drivers
JR Programmer
  • Reads NAND in 3-10 minutes
  • Cheap
  • One of the two options for Sonus sound programming
  • Easy to find
  • More expensive than LPT cable or PicoFlasher
  • Requires unsigned drivers
PicoFlasher
  • Reads NAND fast in 1-8 minutes
  • One of the two options for Sonus sound programming
  • Super cheap
  • Easy to find
  • Uses signed drivers
Matrix USB NAND Flasher
  • Reads NAND in 7-26 minutes
  • Super cheap
  • Requires unsigned drivers
LPT Cable
  • Cheap
  • Doesn't require unsigned drivers
  • Requires PC with parallel port and more equipment
  • More difficult
  • Takes 30-150 minutes to read NANDs

JTAG-Specific Wiring

Choose the guide that pertains to you:

Xenon Method

  • This is the only method for Xenon motherboards. Do not use it if you have a non-Xenon motherboard.

Boxxdr Method

  • This method is for Zephyr, Opus, Falcon, or Jasper motherboards. This method may disable 5.1 audio output.

Boxxdr Method + Open_Tray

  • Use this method if the Boxxdr method doesn't boot, you receive E79 errors, or you have issues with HDMI. This method may cause your DVD drive to eject on bootup. Also, your console will reboot instead of shutting down if you turn off the console while a controller is charging via USB.

Decrypting the NAND

  1. If you can, connect an ethernet cable from the Xbox 360 to your local network or a PC's shared ethernet connection. This will allow you to easily copy the CPU key from a computer, either with J-Runner or with the web page hosted by XeLL. With this CPU key, we can build an XeBuild image, which is a modified NAND dump built specifically for your console.
  2. After writing XeLL to the NAND and completing the JTAG wiring, you should now be able to turn on your Xbox 360 and boot into XeLL to see your CPU key. You can manually type this into J-Runner if you don't have access to an ethernet cable.
    • If you use J-Runner with the console connected to LAN to get the CPU key, enter the IP address XeLL gives you into the lower right of the app. You can then click Get CPU Key and XeLL will automatically decrypt the retail NAND dump you backed up earlier.
    • If you use XeLL over the network to get the CPU key, enter the Xbox's IP address in your preferred web browser. You will see information about the console, and the CPU key can easily be copy and pasted from this web page.

Writing a New NAND Image (NAND Flasher)

  1. Power down the console, and connect your programmer to the motherboard and computer.  
    • If you are using an xFlasher, ensure the switch is set to SPI.
  2. Open J-Runner and select ... next to the Load Source field and either select your nanddump1.bin or nanddump2.bin if not already selected. In the upper right corner of the window, select the dashboard version you chose for the patched dump that you wrote to the motherboard and make sure that the Jtag radio button is selected.
    • If you have a non-Xenon console, the Aud_clamp checkbox should be enabled.
  3. Click "Create XeBuild Image". This will take a few moments.
  4. Click "Write NAND".
  5. Disconnect your programmer when the process completes, and check if the console boots to the Microsoft dashboard. If it successfully boots to the dashboard, it is an indication that you've successfully hacked your console.
    • You may want to leave your Xbox 360 disassembled so that you can:
      • ...disable the eFuse-blowing circuit so you can't accidentally install official updates on your console.
      • ...check what temperatures it's running at so you can judge if you need to replace the thermal paste to avoid overly loud fans and/or overheating issues.
  6. Remove your NAND programmer wires and clean the points. Clean all flux off the board, allow it to dry, and test it once more before re-assembling. You're now free to install XEXMenu (instructions in section below).

Writing a New NAND Image (XeLL)

  1. Open J-Runner and select ... next to the Load Source field and either select your nanddump1.bin or nanddump2.bin if not already selected. In the upper right corner of the window, select the dashboard version you chose for the patched dump that you wrote to the motherboard and make sure that the Jtag radio button is selected.
    • If you have a non-Xenon console, the Aud_clamp checkbox should be enabled.
  2. Click "Create XeBuild Image". This will take a few moments.
  3. Copy updflash.bin to a FAT32 formatted USB storage device and plug it into your powered-off console. Turn on your console and it will boot into XeLL and begin flashing your NAND. Once it has finished, it will power off your console. Turn it back on, and it should boot to the Microsoft dashboard, which is an indication that you've successfully hacked your console.
    • You may want to leave your Xbox 360 disassembled so that you can:
      • ...disable the eFuse-blowing circuit so you can't accidentally install official updates on your console.
      • ...check what temperatures it's running at so you can judge if you need to replace the thermal paste to avoid overly loud fans and/or overheating issues.
  4. Remove your NAND programmer wires (if they are still attached) and clean the points. Clean all flux off the board, allow it to dry, and test it once more before re-assembling. You're now free to install XEXMenu (instructions in section below).

Installing XeXMenu

  1. Plug a flash drive into your Xbox 360 and navigate to Console Settings > Storage. Select the flash drive and allow it to format the flash drive as a system drive.
  2. Extract the CODE9999 folder from the XeXMenu 1.2 rar[6] to your Desktop.
  3. Plug the flash drive into your PC. Open Xplorer360[7] and select Drive > Open > Harddrive or Memcard. On the left-hand side, select Partition 3, then right-click the Content folder, select "New Folder", and name it 0000000000000000 (16 zeroes). Open the new folder, then drag the CODE9999 folder into it.
  4. Select Drive > Close, then close Xplorer360. Safely eject your flash drive and plug it into your Xbox 360. Navigate to the Demos section of your dashboard, and it should list XeXMenu there. Select it to launch it.
    • You can install XeXMenu to your hard drive by going to Console Settings > Storage, and copying it from your flash drive to the hard drive.

From here, you can install any homebrew or mods that you want. See this page for a list of recommended modifications and applications to install.

References